| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Merge series from Sen Wang <sen@ti.com>:
Just two minor patches that aim to tidy up the code a little bit,
as well as fix the aux_div selection in davinci_mcasp_calc_clk_div()
for mid-range dividers (33 <= div <= 4096).
Sen Wang (2):
ASoC: ti: davinci-mcasp: extract mcasp_is_auxclk_enabled() helper
ASoC: ti: davinci-mcasp: improve aux_div selection for mid-range dividers
sound/soc/ti/davinci-mcasp.c | 45 +++++++++++++++++++++++++-----------
1 file changed, 31 insertions(+), 14 deletions(-)
--
2.43.0
|
|
When the ideal total divider (sysclk/bclk) is between 33 and 4096 and
AUXCLK is enabled, the driver computes aux_div as ceil(div/32) and then
recomputes bclk_div from the truncated sysclk.
This two-step integer division loses precision due to truncation and can
sometimes produce PPM errors large enough for ALSA's hw_rule_format to
reject otherwise valid sample formats.
For example, on AM62D-EVM (auxclk-fs-ratio=2177, tdm-slots=2, fck=96 MHz),
playing S16_LE at 44100 Hz gives BCLK = 1,411,200 Hz and an ideal total
divider of 68. The old code picks aux_div = ceil(68/32) = 3,
then bclk_div = (96005700/3) / 1411200 = 22, for a total of 3 x 22 =
66 -- two steps from ideal. The resulting error exceeds the PPM threshold
and causes S16_LE, S24_LE to be rejected.
Therefore when the total divider fits in the AHCLKXDIV register alone
(<=4096), use it directly as aux_div with bclk_div=1, and compare floor
and ceil to pick the closer match, to ensure the best ideal total dividers.
Dividers at or below 32 never enter this path, and dividers above 4096
still fall through to the existing DIV_ROUND_UP path, so previously
working configurations remains unaffected.
Signed-off-by: Sen Wang <sen@ti.com>
Link: https://patch.msgid.link/20260305195825.9998-3-sen@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Move the AUXCLK-enabled check out of davinci_mcasp_calc_clk_div() into
a reusable helper. No functional change.
Signed-off-by: Sen Wang <sen@ti.com>
Link: https://patch.msgid.link/20260305195825.9998-2-sen@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The McASP driver supports runtime PM callbacks for register save/restore
during device idle, but doesn't provide system suspend/resume callbacks.
This causes audio to fail to resume after system suspend.
Since the driver already handles runtime suspend & resume, we can reuse
existing runtime PM logics.
Signed-off-by: Sen Wang <sen@ti.com>
Link: https://patch.msgid.link/20260211221001.155843-1-sen@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
McASP has dedicated clock & frame sync registers for both transmit
and receive. Currently McASP driver only supports synchronous behavior and
couples both TX & RX settings.
Add logic that enables asynchronous mode via ti,async-mode property. In
async mode, playback & record can be done simultaneously with different
audio configurations (tdm slots, tdm width, audio bit depth).
Note the ability to have different tx/rx DSP formats (i2s, dsp_a, etc.),
while possible in hardware, remains to be a gap as it require changes
to the corresponding machine driver interface.
Existing IIS (sync mode) and DIT mode logic remains mostly unchanged.
Exceptions are IIS mode logic that previously assumed sync mode, which has
now been made aware of the distinction. And shared logic across all modes
also now checks for McASP tx/rx-specific driver attributes. Those
attributes have been populated according to the original extent, ensuring
no divergence in functionality.
Constraints no longer applicable for async mode are skipped.
Clock selection options have also been added to include rx/tx-only clk_ids,
exposing independent configuration via the machine driver as well.
Note that asynchronous mode is not applicable for McASP in DIT mode,
which is a transmitter-only mode to interface w/ self-clocking formats.
Signed-off-by: Sen Wang <sen@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Tested-by: Paresh Bhagat <p-bhagat@ti.com>
Link: https://patch.msgid.link/20260203003703.2334443-5-sen@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Simplify the mcasp_set_clk_pdir caller convention in start/stop stream
function, to make it so that set_clk_pdir gets called regardless when
stream starts and also disables when stream ends.
Functionality-wise, everything remains the same as the previously skipped
calls are now either correctly configured
(when McASP is SND_SOC_DAIFMT_BP_FC - pdir needs to be enabled)
or called with a bitmask of zero (when McASP is SND_SOC_DAIFMT_BC_FC - pdir
gets disabled).
On brief regarding McASP Clock and Frame sync configurations, refer to [0].
[0]:TRM Section 12.1.1.4.2 https://www.ti.com/lit/ug/sprujd4a/sprujd4a.pdf
Signed-off-by: Sen Wang <sen@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Tested-by: Paresh Bhagat <p-bhagat@ti.com>
Link: https://patch.msgid.link/20260203003703.2334443-4-sen@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The current mcasp_is_synchronous() function does more than what it
proclaims, it also checks if McASP is a frame producer.
Therefore split the original function into two separate ones and
replace all occurrences with the new equivalent logic.
Signed-off-by: Sen Wang <sen@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Tested-by: Paresh Bhagat <p-bhagat@ti.com>
Link: https://patch.msgid.link/20260203003703.2334443-3-sen@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Merge series from Claudiu <claudiu.beznea@tuxon.dev>:
This series adds cleanups for the Renesas RZ SSI driver.
|
|
The davinci_evm_probe() function calls of_parse_phandle() to acquire
device nodes for "ti,audio-codec" and "ti,mcasp-controller". These
functions return device nodes with incremented reference counts.
However, in several error paths (e.g., when the second of_parse_phandle(),
snd_soc_of_parse_card_name(), or devm_snd_soc_register_card() fails),
the function returns directly without releasing the acquired nodes,
leading to reference leaks.
This patch adds an error handling path 'err_put' to properly release
the device nodes using of_node_put() and clean up the pointers when
an error occurs.
Signed-off-by: Kery Qi <qikeyu2017@gmail.com>
Link: https://patch.msgid.link/20260107154836.1521-2-qikeyu2017@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The enablement of the CONFIG_OF_GPIO switch has nothing to do with the
"gpio-controller" property which may as well come from software nodes
and GPIOLIB can still be enabled separately.
This driver does not call any symbols from gpiolib-of.h so has no need
to check this option at all. Just use the generic device property
accessor.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Link: https://patch.msgid.link/20251205090534.27845-1-bartosz.golaszewski@oss.qualcomm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch converts below functions.
dapm->dev -> snd_soc_dapm_to_dev()
dapm->card -> snd_soc_dapm_to_card()
dapm->component -> snd_soc_dapm_to_component()
dapm_kcontrol_get_value() -> snd_soc_dapm_kcontrol_get_value()
snd_soc_component_enable_pin() -> snd_soc_dapm_enable_pin()
snd_soc_component_enable_pin_unlocked() -> snd_soc_dapm_enable_pin_unlocked()
snd_soc_component_disable_pin() -> snd_soc_dapm_disable_pin()
snd_soc_component_disable_pin_unlocked() -> snd_soc_dapm_disable_pin_unlocked()
snd_soc_component_nc_pin() -> snd_soc_dapm_nc_pin()
snd_soc_component_nc_pin_unlocked() -> snd_soc_dapm_nc_pin_unlocked()
snd_soc_component_get_pin_status() -> snd_soc_dapm_get_pin_status()
snd_soc_component_force_enable_pin() -> snd_soc_dapm_force_enable_pin()
snd_soc_component_force_enable_pin_unlocked() -> snd_soc_dapm_force_enable_pin_unlocked()
snd_soc_component_force_bias_level() -> snd_soc_dapm_force_bias_level()
snd_soc_component_get_bias_level() -> snd_soc_dapm_get_bias_level()
snd_soc_component_init_bias_level() -> snd_soc_dapm_init_bias_level()
snd_soc_component_get_dapm() -> snd_soc_component_to_dapm()
snd_soc_dapm_kcontrol_component() -> snd_soc_dapm_kcontrol_to_component()
snd_soc_dapm_kcontrol_widget() -> snd_soc_dapm_kcontrol_to_widget()
snd_soc_dapm_kcontrol_dapm() -> snd_soc_dapm_kcontrol_to_dapm()
snd_soc_dapm_np_pin() -> snd_soc_dapm_disable_pin()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/87o6p9s8u8.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch converts below functions.
dapm->dev -> snd_soc_dapm_to_dev()
dapm->card -> snd_soc_dapm_to_card()
dapm->component -> snd_soc_dapm_to_component()
dapm_kcontrol_get_value() -> snd_soc_dapm_kcontrol_get_value()
snd_soc_component_enable_pin() -> snd_soc_dapm_enable_pin()
snd_soc_component_enable_pin_unlocked() -> snd_soc_dapm_enable_pin_unlocked()
snd_soc_component_disable_pin() -> snd_soc_dapm_disable_pin()
snd_soc_component_disable_pin_unlocked() -> snd_soc_dapm_disable_pin_unlocked()
snd_soc_component_nc_pin() -> snd_soc_dapm_nc_pin()
snd_soc_component_nc_pin_unlocked() -> snd_soc_dapm_nc_pin_unlocked()
snd_soc_component_get_pin_status() -> snd_soc_dapm_get_pin_status()
snd_soc_component_force_enable_pin() -> snd_soc_dapm_force_enable_pin()
snd_soc_component_force_enable_pin_unlocked() -> snd_soc_dapm_force_enable_pin_unlocked()
snd_soc_component_force_bias_level() -> snd_soc_dapm_force_bias_level()
snd_soc_component_get_bias_level() -> snd_soc_dapm_get_bias_level()
snd_soc_component_init_bias_level() -> snd_soc_dapm_init_bias_level()
snd_soc_component_get_dapm() -> snd_soc_component_to_dapm()
snd_soc_dapm_kcontrol_component() -> snd_soc_dapm_kcontrol_to_component()
snd_soc_dapm_kcontrol_widget() -> snd_soc_dapm_kcontrol_to_widget()
snd_soc_dapm_kcontrol_dapm() -> snd_soc_dapm_kcontrol_to_dapm()
snd_soc_dapm_np_pin() -> snd_soc_dapm_disable_pin()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/87pl9ps8ub.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch converts below functions.
dapm->dev -> snd_soc_dapm_to_dev()
dapm->card -> snd_soc_dapm_to_card()
dapm->component -> snd_soc_dapm_to_component()
dapm_kcontrol_get_value() -> snd_soc_dapm_kcontrol_get_value()
snd_soc_component_enable_pin() -> snd_soc_dapm_enable_pin()
snd_soc_component_enable_pin_unlocked() -> snd_soc_dapm_enable_pin_unlocked()
snd_soc_component_disable_pin() -> snd_soc_dapm_disable_pin()
snd_soc_component_disable_pin_unlocked() -> snd_soc_dapm_disable_pin_unlocked()
snd_soc_component_nc_pin() -> snd_soc_dapm_nc_pin()
snd_soc_component_nc_pin_unlocked() -> snd_soc_dapm_nc_pin_unlocked()
snd_soc_component_get_pin_status() -> snd_soc_dapm_get_pin_status()
snd_soc_component_force_enable_pin() -> snd_soc_dapm_force_enable_pin()
snd_soc_component_force_enable_pin_unlocked() -> snd_soc_dapm_force_enable_pin_unlocked()
snd_soc_component_force_bias_level() -> snd_soc_dapm_force_bias_level()
snd_soc_component_get_bias_level() -> snd_soc_dapm_get_bias_level()
snd_soc_component_init_bias_level() -> snd_soc_dapm_init_bias_level()
snd_soc_component_get_dapm() -> snd_soc_component_to_dapm()
snd_soc_dapm_kcontrol_component() -> snd_soc_dapm_kcontrol_to_component()
snd_soc_dapm_kcontrol_widget() -> snd_soc_dapm_kcontrol_to_widget()
snd_soc_dapm_kcontrol_dapm() -> snd_soc_dapm_kcontrol_to_dapm()
snd_soc_dapm_np_pin() -> snd_soc_dapm_disable_pin()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/87qzu5s8uf.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch converts below functions.
dapm->dev -> snd_soc_dapm_to_dev()
dapm->card -> snd_soc_dapm_to_card()
dapm->component -> snd_soc_dapm_to_component()
dapm_kcontrol_get_value() -> snd_soc_dapm_kcontrol_get_value()
snd_soc_component_enable_pin() -> snd_soc_dapm_enable_pin()
snd_soc_component_enable_pin_unlocked() -> snd_soc_dapm_enable_pin_unlocked()
snd_soc_component_disable_pin() -> snd_soc_dapm_disable_pin()
snd_soc_component_disable_pin_unlocked() -> snd_soc_dapm_disable_pin_unlocked()
snd_soc_component_nc_pin() -> snd_soc_dapm_nc_pin()
snd_soc_component_nc_pin_unlocked() -> snd_soc_dapm_nc_pin_unlocked()
snd_soc_component_get_pin_status() -> snd_soc_dapm_get_pin_status()
snd_soc_component_force_enable_pin() -> snd_soc_dapm_force_enable_pin()
snd_soc_component_force_enable_pin_unlocked() -> snd_soc_dapm_force_enable_pin_unlocked()
snd_soc_component_force_bias_level() -> snd_soc_dapm_force_bias_level()
snd_soc_component_get_bias_level() -> snd_soc_dapm_get_bias_level()
snd_soc_component_init_bias_level() -> snd_soc_dapm_init_bias_level()
snd_soc_component_get_dapm() -> snd_soc_component_to_dapm()
snd_soc_dapm_kcontrol_component() -> snd_soc_dapm_kcontrol_to_component()
snd_soc_dapm_kcontrol_widget() -> snd_soc_dapm_kcontrol_to_widget()
snd_soc_dapm_kcontrol_dapm() -> snd_soc_dapm_kcontrol_to_dapm()
snd_soc_dapm_np_pin() -> snd_soc_dapm_disable_pin()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/87seels8ui.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch converts below functions.
dapm->dev -> snd_soc_dapm_to_dev()
dapm->card -> snd_soc_dapm_to_card()
dapm->component -> snd_soc_dapm_to_component()
dapm_kcontrol_get_value() -> snd_soc_dapm_kcontrol_get_value()
snd_soc_component_enable_pin() -> snd_soc_dapm_enable_pin()
snd_soc_component_enable_pin_unlocked() -> snd_soc_dapm_enable_pin_unlocked()
snd_soc_component_disable_pin() -> snd_soc_dapm_disable_pin()
snd_soc_component_disable_pin_unlocked() -> snd_soc_dapm_disable_pin_unlocked()
snd_soc_component_nc_pin() -> snd_soc_dapm_nc_pin()
snd_soc_component_nc_pin_unlocked() -> snd_soc_dapm_nc_pin_unlocked()
snd_soc_component_get_pin_status() -> snd_soc_dapm_get_pin_status()
snd_soc_component_force_enable_pin() -> snd_soc_dapm_force_enable_pin()
snd_soc_component_force_enable_pin_unlocked() -> snd_soc_dapm_force_enable_pin_unlocked()
snd_soc_component_force_bias_level() -> snd_soc_dapm_force_bias_level()
snd_soc_component_get_bias_level() -> snd_soc_dapm_get_bias_level()
snd_soc_component_init_bias_level() -> snd_soc_dapm_init_bias_level()
snd_soc_component_get_dapm() -> snd_soc_component_to_dapm()
snd_soc_dapm_kcontrol_component() -> snd_soc_dapm_kcontrol_to_component()
snd_soc_dapm_kcontrol_widget() -> snd_soc_dapm_kcontrol_to_widget()
snd_soc_dapm_kcontrol_dapm() -> snd_soc_dapm_kcontrol_to_dapm()
snd_soc_dapm_np_pin() -> snd_soc_dapm_disable_pin()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/87tsz1s8ul.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch converts below functions.
dapm->dev -> snd_soc_dapm_to_dev()
dapm->card -> snd_soc_dapm_to_card()
dapm->component -> snd_soc_dapm_to_component()
dapm_kcontrol_get_value() -> snd_soc_dapm_kcontrol_get_value()
snd_soc_component_enable_pin() -> snd_soc_dapm_enable_pin()
snd_soc_component_enable_pin_unlocked() -> snd_soc_dapm_enable_pin_unlocked()
snd_soc_component_disable_pin() -> snd_soc_dapm_disable_pin()
snd_soc_component_disable_pin_unlocked() -> snd_soc_dapm_disable_pin_unlocked()
snd_soc_component_nc_pin() -> snd_soc_dapm_nc_pin()
snd_soc_component_nc_pin_unlocked() -> snd_soc_dapm_nc_pin_unlocked()
snd_soc_component_get_pin_status() -> snd_soc_dapm_get_pin_status()
snd_soc_component_force_enable_pin() -> snd_soc_dapm_force_enable_pin()
snd_soc_component_force_enable_pin_unlocked() -> snd_soc_dapm_force_enable_pin_unlocked()
snd_soc_component_force_bias_level() -> snd_soc_dapm_force_bias_level()
snd_soc_component_get_bias_level() -> snd_soc_dapm_get_bias_level()
snd_soc_component_init_bias_level() -> snd_soc_dapm_init_bias_level()
snd_soc_component_get_dapm() -> snd_soc_component_to_dapm()
snd_soc_dapm_kcontrol_component() -> snd_soc_dapm_kcontrol_to_component()
snd_soc_dapm_kcontrol_widget() -> snd_soc_dapm_kcontrol_to_widget()
snd_soc_dapm_kcontrol_dapm() -> snd_soc_dapm_kcontrol_to_dapm()
snd_soc_dapm_np_pin() -> snd_soc_dapm_disable_pin()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/87v7jhs8uo.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch converts below functions.
dapm->dev -> snd_soc_dapm_to_dev()
dapm->card -> snd_soc_dapm_to_card()
dapm->component -> snd_soc_dapm_to_component()
dapm_kcontrol_get_value() -> snd_soc_dapm_kcontrol_get_value()
snd_soc_component_enable_pin() -> snd_soc_dapm_enable_pin()
snd_soc_component_enable_pin_unlocked() -> snd_soc_dapm_enable_pin_unlocked()
snd_soc_component_disable_pin() -> snd_soc_dapm_disable_pin()
snd_soc_component_disable_pin_unlocked() -> snd_soc_dapm_disable_pin_unlocked()
snd_soc_component_nc_pin() -> snd_soc_dapm_nc_pin()
snd_soc_component_nc_pin_unlocked() -> snd_soc_dapm_nc_pin_unlocked()
snd_soc_component_get_pin_status() -> snd_soc_dapm_get_pin_status()
snd_soc_component_force_enable_pin() -> snd_soc_dapm_force_enable_pin()
snd_soc_component_force_enable_pin_unlocked() -> snd_soc_dapm_force_enable_pin_unlocked()
snd_soc_component_force_bias_level() -> snd_soc_dapm_force_bias_level()
snd_soc_component_get_bias_level() -> snd_soc_dapm_get_bias_level()
snd_soc_component_init_bias_level() -> snd_soc_dapm_init_bias_level()
snd_soc_component_get_dapm() -> snd_soc_component_to_dapm()
snd_soc_dapm_kcontrol_component() -> snd_soc_dapm_kcontrol_to_component()
snd_soc_dapm_kcontrol_widget() -> snd_soc_dapm_kcontrol_to_widget()
snd_soc_dapm_kcontrol_dapm() -> snd_soc_dapm_kcontrol_to_dapm()
snd_soc_dapm_np_pin() -> snd_soc_dapm_disable_pin()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/87wm3xs8ur.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch converts below functions.
dapm->dev -> snd_soc_dapm_to_dev()
dapm->card -> snd_soc_dapm_to_card()
dapm->component -> snd_soc_dapm_to_component()
dapm_kcontrol_get_value() -> snd_soc_dapm_kcontrol_get_value()
snd_soc_component_enable_pin() -> snd_soc_dapm_enable_pin()
snd_soc_component_enable_pin_unlocked() -> snd_soc_dapm_enable_pin_unlocked()
snd_soc_component_disable_pin() -> snd_soc_dapm_disable_pin()
snd_soc_component_disable_pin_unlocked() -> snd_soc_dapm_disable_pin_unlocked()
snd_soc_component_nc_pin() -> snd_soc_dapm_nc_pin()
snd_soc_component_nc_pin_unlocked() -> snd_soc_dapm_nc_pin_unlocked()
snd_soc_component_get_pin_status() -> snd_soc_dapm_get_pin_status()
snd_soc_component_force_enable_pin() -> snd_soc_dapm_force_enable_pin()
snd_soc_component_force_enable_pin_unlocked() -> snd_soc_dapm_force_enable_pin_unlocked()
snd_soc_component_force_bias_level() -> snd_soc_dapm_force_bias_level()
snd_soc_component_get_bias_level() -> snd_soc_dapm_get_bias_level()
snd_soc_component_init_bias_level() -> snd_soc_dapm_init_bias_level()
snd_soc_component_get_dapm() -> snd_soc_component_to_dapm()
snd_soc_dapm_kcontrol_component() -> snd_soc_dapm_kcontrol_to_component()
snd_soc_dapm_kcontrol_widget() -> snd_soc_dapm_kcontrol_to_widget()
snd_soc_dapm_kcontrol_dapm() -> snd_soc_dapm_kcontrol_to_dapm()
snd_soc_dapm_np_pin() -> snd_soc_dapm_disable_pin()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/87y0ods8uu.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The conversion of all GPIO drivers to using the .set_rv() and
.set_multiple_rv() callbacks from struct gpio_chip (which - unlike their
predecessors - return an integer and allow the controller drivers to
indicate failures to users) is now complete and the legacy ones have
been removed. Rename the new callbacks back to their original names in
one sweeping change.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Current Kconfig menu at [ALSA for SoC audio support] has no rules.
So, some venders are using menu style, some venders are listed each drivers
on top page, etc. It is difficult to find target vender and/or drivers
because it is very random.
Let's standardize ASoC menu
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://patch.msgid.link/874iwl20th.wl-kuninori.morimoto.gx@renesas.com
Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The removed dai_link->platform component cause a fail which
is exposed at runtime. (ex: when a sound tool is used)
This patch re-adds the dai_link->platform component to have
a full card registered.
Before this patch:
$ aplay -l
**** List of PLAYBACK Hardware Devices ****
card 1: HDMI [HDMI], device 0: HDMI snd-soc-dummy-dai-0 []
Subdevices: 1/1
Subdevice #0: subdevice #0
$ speaker-test -D plughw:1,0 -t sine
speaker-test 1.2.8
Playback device is plughw:1,0
Stream parameters are 48000Hz, S16_LE, 1 channels
Sine wave rate is 440.0000Hz
Playback open error: -22,Invalid argument
After this patch which restores the platform component:
$ aplay -l
**** List of PLAYBACK Hardware Devices ****
card 0: HDMI [HDMI], device 0: HDMI snd-soc-dummy-dai-0 [HDMI snd-soc-dummy-dai-0]
Subdevices: 0/1
Subdevice #0: subdevice #0
-> Resolve the playback error.
Fixes: 3b0db249cf8f ("ASoC: ti: remove unnecessary dai_link->platform")
Signed-off-by: Yuuki NAGAO <wf.yn386@gmail.com>
Link: https://patch.msgid.link/20250531141341.81164-1-wf.yn386@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
struct gpio_chip now has callbacks for setting line values that return
an integer, allowing to indicate failures. Convert the driver to using
them.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://patch.msgid.link/20250408-gpiochip-set-rv-sound-v1-2-dd54b6ca1ef9@linaro.org
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
timer_delete[_sync]() replaces del_timer[_sync](). Convert the whole tree
over and remove the historical wrapper inlines.
Conversion was done with coccinelle plus manual fixups where necessary.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v6.15
This is a very big release due to a combination of some big new work,
mainly new drivers and generic SoundWire support, and some wide ranging
cleanup work that made small changes to a lot of drivers.
- Morimoto-san has completed the conversion to use modern terminology
for the clocking configuration, and several other cleanups with
narrower impact.
- All the power management operation configuration was updated to use
current idioms by Takashi Iwai.
- Clarification of the control operations from Charles Keepax.
- Prepartory work for more generic SoundWire SCDA controls from Charles
Keepax.
- Support for AMD ACP 7.x, AWINC WM88166, Everest ES8388, Intel AVS
PEAKVOL and GAIN DSP modules Mediatek MT8188 DMIC, NXP i.MX95, nVidia
Tegra interconnects, Rockchip RK3588 S/PDIF, Texas Instruments
SN012776 and TAS5770L, and Wolfson WM8904 DMICs,
Some changes from the tip tree adding APIs needed by the AMD code are
included, these were unfortunately rebased in the tip tree after being
pulled in. There's also some regmap changes supporting the SCDA work
and some devres refactoring that was pulled in to support other changes.
|
|
For 'ti,j7200-cpb-audio' compatible, there is support for only one PLL for
48k. For 11025, 22050, 44100 and 88200 sampling rates, due to absence of
J721E_CLK_PARENT_44100, we get EINVAL while running any audio application.
Add support for these rates by using the 48k parent clock and adjusting
the clock for these rates later in j721e_configure_refclk.
Fixes: 6748d0559059 ("ASoC: ti: Add custom machine driver for j721e EVM (CPB and IVI)")
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Link: https://patch.msgid.link/20250318113524.57100-1-j-choudhary@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Drop the log level for deferral probe to avoid flooding in kernel logs.
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Link: https://patch.msgid.link/20250318104715.43267-1-j-choudhary@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
clk_disable_unprepare()
clk_disable_unprepare() already checks NULL by using IS_ERR_OR_NULL.
Remove unneeded NULL check for dev->ext_clk here.
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Link: https://patch.msgid.link/20250312033509.1235268-1-nichen@iscas.ac.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In SND_SOC_DAIFMT_CBx_CFx, M/S are no longer used. use P/C.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://patch.msgid.link/874j0hh4r5.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In SND_SOC_DAIFMT_CBx_CFx, M/S are no longer used. use P/C.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://patch.msgid.link/875xkxh4ra.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In SND_SOC_DAIFMT_CBx_CFx, M/S are no longer used. use P/C.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://patch.msgid.link/877c5dh4re.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In SND_SOC_DAIFMT_CBx_CFx, M/S are no longer used. use P/C.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://patch.msgid.link/878qpth4ri.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In SND_SOC_DAIFMT_CBx_CFx, M/S are no longer used. use P/C.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://patch.msgid.link/87a5a9h4rr.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In SND_SOC_DAIFMT_CBx_CFx, M/S are no longer used. use P/C.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://patch.msgid.link/87bjuph4rw.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In SND_SOC_DAIFMT_CBx_CFx, M/S are no longer used. use P/C.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://patch.msgid.link/87cyf5h4s0.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In SND_SOC_DAIFMT_CBx_CFx, M/S are no longer used. use P/C.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://patch.msgid.link/87frkaviho.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
dev_err function
Because card->dev = &pdev->dev is already defined in the rx51_soc_probe
function, and then &pdev->dev is still used.
Signed-off-by: Liu Jing <liujing@cmss.chinamobile.com>
Link: https://patch.msgid.link/20241015074938.6247-1-liujing@cmss.chinamobile.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
After commit 0edb555a65d1 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all drivers below sound/soc to use .remove(), with the eventual
goal to drop struct platform_driver::remove_new(). As .remove() and
.remove_new() have the same prototypes, conversion is done by just
changing the structure member name in the driver initializer.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://patch.msgid.link/20240909151230.909818-2-u.kleine-koenig@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Merge series from Jai Luthra <j-luthra@ti.com>:
This series fixes two patches:
1. Fix the dmaengine API usage by calling dmaengine_synchronize() after
dmaengine_terminate_async() when xrun events occur in application
2. Use the McASP AFIFO property from DT to refine the period size,
instead of hardcoding minimum to 64 samples
|
|
Set driver name to "HDMI". This simplifies the code and gets rid of
the following error messages:
ASoC: driver name too long 'HDMI 58040000.encoder' -> 'HDMI_58040000_e'
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Link: https://lore.kernel.org/r/20240610125847.773394-1-primoz.fiser@norik.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The minimum period size was enforced to 64 as older devices integrating
McASP with EDMA used an internal FIFO of 64 samples.
With UDMA based platforms this internal McASP FIFO is optional, as the
DMA engine internally does some buffering which is already accounted for
when registering the platform. So we should read the actual FIFO
configuration (txnumevt/rxnumevt) instead of hardcoding frames.min to
64.
Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20240611-asoc_next-v3-2-fcfd84b12164@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
*-objs suffix is reserved rather for (user-space) host programs while
usually *-y suffix is used for kernel drivers (although *-objs works
for that purpose for now).
Let's correct the old usages of *-objs in Makefiles.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20240507155540.24815-31-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Do not open-code snd_soc_substream_to_rtd().
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240430-asoc-snd-substream-clean-v1-3-6f8a8902b479@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Some new SOF changes depend on the fixes there.
|
|
When using davinci-mcasp as CPU DAI with simple-card, there are some
conditions that cause simple-card to finish registering a sound card before
davinci-mcasp finishes registering all sound components. This creates a
non-working sound card from userspace with no problem indication apart
from not being able to play/record audio on a PCM stream. The issue
arises during simultaneous probe execution of both drivers. Specifically,
the simple-card driver, awaiting a CPU DAI, proceeds as soon as
davinci-mcasp registers its DAI. However, this process can lead to the
client mutex lock (client_mutex in soc-core.c) being held or davinci-mcasp
being preempted before PCM DMA registration on davinci-mcasp finishes.
This situation occurs when the probes of both drivers run concurrently.
Below is the code path for this condition. To solve the issue, defer
davinci-mcasp CPU DAI registration to the last step in the audio part of
it. This way, simple-card CPU DAI parsing will be deferred until all
audio components are registered.
Fail Code Path:
simple-card.c: probe starts
simple-card.c: simple_dai_link_of: simple_parse_node(..,cpu,..) returns EPROBE_DEFER, no CPU DAI yet
davinci-mcasp.c: probe starts
davinci-mcasp.c: devm_snd_soc_register_component() register CPU DAI
simple-card.c: probes again, finish CPU DAI parsing and call devm_snd_soc_register_card()
simple-card.c: finish probe
davinci-mcasp.c: *dma_pcm_platform_register() register PCM DMA
davinci-mcasp.c: probe finish
Cc: stable@vger.kernel.org
Fixes: 9fbd58cf4ab0 ("ASoC: davinci-mcasp: Choose PCM driver based on configured DMA controller")
Signed-off-by: Joao Paulo Goncalves <joao.goncalves@toradex.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Reviewed-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20240417184138.1104774-1-jpaulo.silvagoncalves@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
McBSP's data delay can be configured from 0 to 2 bit clock periods. 0 is
used for DSP_B format, 1 is used for DSP_A format, 2 is unused.
A data delay of 2 bit clock periods can be used to interface to
'T1 framing' devices where data stream is preceded by a 'framing bit'. On
transmission, McBSP inserts a blank period (high-impedance period)
before the first data bit to leave an opportunity for other devices to
set this 'framing bit'. On reception, McBSP discards the 'framing bit'
that precedes the data stream.
Add support for the 'framing bit' according to the
'ti,T1-framing-[tx/rx]' device-tree properties. If a flag is present,
the data delay is set to 2 bit clock periods regardless of the selected
DAI format.
Signed-off-by: Bastien Curutchet <bastien.curutchet@bootlin.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Link: https://msgid.link/r/20240402071213.11671-14-bastien.curutchet@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
S24_LE is supported by McBSP but not by the driver.
Add S24_LE to driver's supported formats. Using it enables the sign
extension in DRR (Data Receive Register). The other formats are kept
with the zero extension in DRR.
Remove data_type table as it is no longer used.
Signed-off-by: Bastien Curutchet <bastien.curutchet@bootlin.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Link: https://msgid.link/r/20240402071213.11671-12-bastien.curutchet@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
McBSP has free-running mode where serial clocks continue to run during
emulation halts. This mode is always enabled by the driver.
Set free-running mode when SND_SOC_DAIFMT_CONT is selected by DAI
format, unset it when SND_SOC_DAIFMT_GATED is selected.
Signed-off-by: Bastien Curutchet <bastien.curutchet@bootlin.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Link: https://msgid.link/r/20240402071213.11671-11-bastien.curutchet@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
McBSP can generate a SYNCERR when unexpected frame pulses are
detected. The driver always disables this feature and ignore the
unexpected frame pulses.
Enable the generation of SYNCERR by the McBSP. Unexpected frame
pulses are not ignored anymore.
Signed-off-by: Bastien Curutchet <bastien.curutchet@bootlin.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Link: https://msgid.link/r/20240402071213.11671-10-bastien.curutchet@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
McBSP is able to drive bit clock and consume frame clock but BP_FC
format is not handled by McBSP driver.
Add BP_FC format support.
When BP_FC is selected:
- CLKX and CLKR are configured as outputs
- The sample rate generator is configured to be able to provide bit
clock.
Signed-off-by: Bastien Curutchet <bastien.curutchet@bootlin.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Link: https://msgid.link/r/20240402071213.11671-9-bastien.curutchet@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
TDM is not supported by the McBSP driver. The McBSP datasheet does not
name explicitly TDM as a supported format but it is possible to configure
the McBSP to do TDM if all slots are used by McBSP.
Add TDM support. It uses single-phase frame. Slot width is used to
compute the McBSP's word length.
Implement the set_tdm_slot() hook of snd_soc_dai_ops struct. It only
supports TDM if all slots are used by McBSP.
The snd_soc_dai_driver's channels_max is updated from 2 to 128.
This was tested with BP_FC format on a platform designed off of
DAVINCI/OMAP_L138. A check is done in davinci_i2s_set_dai_fmt() to
prevent TDM to be used with BC_FC and BC_FP formats.
Signed-off-by: Bastien Curutchet <bastien.curutchet@bootlin.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Link: https://msgid.link/r/20240402071213.11671-8-bastien.curutchet@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
