| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux into soc/drivers-late
standalone cache drivers for v6.19
ccache:
Add a compatible for the pic64gx SoC. No driver change needed, as it
falls back to the PolarFire SoC.
hisi hha/generic cpu cache maintenance:
Add support for a non-architectural mechanism for invalidating memory
regions, needed for some cxl implementations on arm64 (and probably
elsewhere in the future). The HiSilicon Hydra Home Agent is the first
driver to provide this support.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
* tag 'cache-for-v6.19' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux:
MAINTAINERS: refer to intended file in STANDALONE CACHE CONTROLLER DRIVERS
cache: Support cache maintenance for HiSilicon SoC Hydra Home Agent
cache: Make top level Kconfig menu a boolean dependent on RISCV
MAINTAINERS: Add Jonathan Cameron to drivers/cache and add lib/cache_maint.c + header
arm64: Select GENERIC_CPU_CACHE_MAINTENANCE
lib: Support ARCH_HAS_CPU_CACHE_INVALIDATE_MEMREGION
memregion: Support fine grained invalidate by cpu_cache_invalidate_memregion()
memregion: Drop unused IORES_DESC_* parameter from cpu_cache_invalidate_memregion()
dt-bindings: cache: sifive,ccache0: add a pic64gx compatible
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
ARCH_HAS_CPU_CACHE_INVALIDATE_MEMREGION provides the mechanism for
invalidating certain memory regions in a cache-incoherent manner. Currently
this is used by NVDIMM and CXL memory drivers in cases where it is
necessary to flush all data from caches by physical address range.
The operations in question are effectively memory hotplug, where stale
data might otherwise remain in the caches.
This is separate from the invalidates done to enable use of non-coherent
DMA masters, primarily in terms of when it is needed (not related to DMA
mappings) and how deep the flush must push data. The flushes done for
non-coherent DMA only need to reach the Point of Coherence of a single host
(which is often nearer CPUs and DMA masters than the physical storage).
This operation must push the data out of non architectural caches
(memory-side caches, write buffers etc) and typically all the way to the
memory device.
In some architectures these operations are supported by system components
that may become available only later in boot as they are either present
on a discoverable bus, or via a firmware description of an MMIO interface
(e.g. ACPI DSDT). Provide a framework to handle this case.
Architectures can opt in for this support via
CONFIG_GENERIC_CPU_CACHE_MAINTENANCE
Add a registration framework. Each driver provides an ops structure and
the first op is Write Back and Invalidate by PA Range. The driver may
over invalidate.
For systems that can perform this operation asynchronously an optional
completion check operation is also provided. If present that must be called
to ensure that the action has finished. This provides a considerable
performance advantage if multiple agents are involved in the maintenance
operation.
When multiple agents are present in the system each should register with
this framework and the core code will issue the invalidate to all of them
before checking for completion on each. This is done to avoid need for
filtering in the core code which can become complex when interleave,
potentially across different cache coherency hardware is going on, so it
is easier to tell everyone and let those who don't care do nothing.
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Co-developed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
Pull bitmap updates from Yury Norov:
- FIELD_PREP_WM16() consolidation (Nicolas)
- bitmaps for Rust (Burak)
- __fls() fix for arc (Kees)
* tag 'bitmap-for-6.18' of https://github.com/norov/linux: (25 commits)
rust: add dynamic ID pool abstraction for bitmap
rust: add find_bit_benchmark_rust module.
rust: add bitmap API.
rust: add bindings for bitops.h
rust: add bindings for bitmap.h
phy: rockchip-pcie: switch to FIELD_PREP_WM16 macro
clk: sp7021: switch to FIELD_PREP_WM16 macro
PCI: dw-rockchip: Switch to FIELD_PREP_WM16 macro
PCI: rockchip: Switch to FIELD_PREP_WM16* macros
net: stmmac: dwmac-rk: switch to FIELD_PREP_WM16 macro
ASoC: rockchip: i2s-tdm: switch to FIELD_PREP_WM16_CONST macro
drm/rockchip: dw_hdmi: switch to FIELD_PREP_WM16* macros
phy: rockchip-usb: switch to FIELD_PREP_WM16 macro
drm/rockchip: inno-hdmi: switch to FIELD_PREP_WM16 macro
drm/rockchip: dw_hdmi_qp: switch to FIELD_PREP_WM16 macro
phy: rockchip-samsung-dcphy: switch to FIELD_PREP_WM16 macro
drm/rockchip: vop2: switch to FIELD_PREP_WM16 macro
drm/rockchip: dsi: switch to FIELD_PREP_WM16* macros
phy: rockchip-emmc: switch to FIELD_PREP_WM16 macro
drm/rockchip: lvds: switch to FIELD_PREP_WM16 macro
...
|
|
Microbenchmark protected by a config FIND_BIT_BENCHMARK_RUST,
following `find_bit_benchmark.c` but testing the Rust Bitmap API.
We add a fill_random() method protected by the config in order to
maintain the abstraction.
The sample output from the benchmark, both C and Rust version:
find_bit_benchmark.c output:
```
Start testing find_bit() with random-filled bitmap
[ 438.101937] find_next_bit: 860188 ns, 163419 iterations
[ 438.109471] find_next_zero_bit: 912342 ns, 164262 iterations
[ 438.116820] find_last_bit: 726003 ns, 163419 iterations
[ 438.130509] find_nth_bit: 7056993 ns, 16269 iterations
[ 438.139099] find_first_bit: 1963272 ns, 16270 iterations
[ 438.173043] find_first_and_bit: 27314224 ns, 32654 iterations
[ 438.180065] find_next_and_bit: 398752 ns, 73705 iterations
[ 438.186689]
Start testing find_bit() with sparse bitmap
[ 438.193375] find_next_bit: 9675 ns, 656 iterations
[ 438.201765] find_next_zero_bit: 1766136 ns, 327025 iterations
[ 438.208429] find_last_bit: 9017 ns, 656 iterations
[ 438.217816] find_nth_bit: 2749742 ns, 655 iterations
[ 438.225168] find_first_bit: 721799 ns, 656 iterations
[ 438.231797] find_first_and_bit: 2819 ns, 1 iterations
[ 438.238441] find_next_and_bit: 3159 ns, 1 iterations
```
find_bit_benchmark_rust.rs output:
```
[ 451.182459] find_bit_benchmark_rust:
[ 451.186688] Start testing find_bit() Rust with random-filled bitmap
[ 451.194450] next_bit: 777950 ns, 163644 iterations
[ 451.201997] next_zero_bit: 918889 ns, 164036 iterations
[ 451.208642] Start testing find_bit() Rust with sparse bitmap
[ 451.214300] next_bit: 9181 ns, 654 iterations
[ 451.222806] next_zero_bit: 1855504 ns, 327026 iterations
```
Here are the results from 32 samples, with 95% confidence interval.
The microbenchmark was built with RUST_BITMAP_HARDENED=n and run on a
machine that did not execute other processes.
Random-filled bitmap:
+-----------+-------+-----------+--------------+-----------+-----------+
| Benchmark | Lang | Mean (ms) | Std Dev (ms) | 95% CI Lo | 95% CI Hi |
+-----------+-------+-----------+--------------+-----------+-----------+
| find_bit/ | C | 825.07 | 53.89 | 806.40 | 843.74 |
| next_bit | Rust | 870.91 | 46.29 | 854.88 | 886.95 |
+-----------+-------+-----------+--------------+-----------+-----------+
| find_zero/| C | 933.56 | 56.34 | 914.04 | 953.08 |
| next_zero | Rust | 945.85 | 60.44 | 924.91 | 966.79 |
+-----------+-------+-----------+--------------+-----------+-----------+
Rust appears 5.5% slower for next_bit, 1.3% slower for next_zero.
Sparse bitmap:
+-----------+-------+-----------+--------------+-----------+-----------+
| Benchmark | Lang | Mean (ms) | Std Dev (ms) | 95% CI Lo | 95% CI Hi |
+-----------+-------+-----------+--------------+-----------+-----------+
| find_bit/ | C | 13.17 | 6.21 | 11.01 | 15.32 |
| next_bit | Rust | 14.30 | 8.27 | 11.43 | 17.17 |
+-----------+-------+-----------+--------------+-----------+-----------+
| find_zero/| C | 1859.31 | 82.30 | 1830.80 | 1887.83 |
| next_zero | Rust | 1908.09 | 139.82 | 1859.65 | 1956.54 |
+-----------+-------+-----------+--------------+-----------+-----------+
Rust appears 8.5% slower for next_bit, 2.6% slower for next_zero.
In summary, taking the arithmetic mean of all slow-downs, we can say
the Rust API has a 4.5% slowdown.
Suggested-by: Alice Ryhl <aliceryhl@google.com>
Suggested-by: Yury Norov (NVIDIA) <yury.norov@gmail.com>
Reviewed-by: Yury Norov (NVIDIA) <yury.norov@gmail.com>
Reviewed-by: Alice Ryhl <aliceryhl@google.com>
Signed-off-by: Burak Emir <bqe@google.com>
Signed-off-by: Yury Norov (NVIDIA) <yury.norov@gmail.com>
|
|
For kbuild to properly clean up these build artifacts in the subdirectory,
even after CONFIG_KUNIT changed do disabled, the directory needs to be
processed always.
Pushing the special logic for hook.o into the kunit Makefile also makes the
logic easier to understand.
Link: https://lore.kernel.org/r/20250813-kunit-always-descend-v1-1-7bbd387ff13b@linutronix.de
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Reviewed-by: David Gow <davidgow@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull non-MM updates from Andrew Morton:
"Significant patch series in this pull request:
- "squashfs: Remove page->mapping references" (Matthew Wilcox) gets
us closer to being able to remove page->mapping
- "relayfs: misc changes" (Jason Xing) does some maintenance and
minor feature addition work in relayfs
- "kdump: crashkernel reservation from CMA" (Jiri Bohac) switches
us from static preallocation of the kdump crashkernel's working
memory over to dynamic allocation. So the difficulty of a-priori
estimation of the second kernel's needs is removed and the first
kernel obtains extra memory
- "generalize panic_print's dump function to be used by other
kernel parts" (Feng Tang) implements some consolidation and
rationalization of the various ways in which a failing kernel
splats information at the operator
* tag 'mm-nonmm-stable-2025-08-03-12-47' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (80 commits)
tools/getdelays: add backward compatibility for taskstats version
kho: add test for kexec handover
delaytop: enhance error logging and add PSI feature description
samples: Kconfig: fix spelling mistake "instancess" -> "instances"
fat: fix too many log in fat_chain_add()
scripts/spelling.txt: add notifer||notifier to spelling.txt
xen/xenbus: fix typo "notifer"
net: mvneta: fix typo "notifer"
drm/xe: fix typo "notifer"
cxl: mce: fix typo "notifer"
KVM: x86: fix typo "notifer"
MAINTAINERS: add maintainers for delaytop
ucount: use atomic_long_try_cmpxchg() in atomic_long_inc_below()
ucount: fix atomic_long_inc_below() argument type
kexec: enable CMA based contiguous allocation
stackdepot: make max number of pools boot-time configurable
lib/xxhash: remove unused functions
init/Kconfig: restore CONFIG_BROKEN help text
lib/raid6: update recov_rvv.c zero page usage
docs: update docs after introducing delaytop
...
|
|
Testing kexec handover requires a kernel driver that will generate some
data and preserve it with KHO on the first boot and then restore that data
and verify it was preserved properly after kexec.
To facilitate such test, along with the kernel driver responsible for data
generation, preservation and restoration add a script that runs a kernel
in a VM with a minimal /init. The /init enables KHO, loads a kernel image
for kexec and runs kexec reboot. After the boot of the kexeced kernel,
the driver verifies that the data was properly preserved.
[rppt@kernel.org: fix section mismatch]
Link: https://lkml.kernel.org/r/aIiRC8fXiOXKbPM_@kernel.org
Link: https://lkml.kernel.org/r/20250727083733.2590139-1-rppt@kernel.org
Signed-off-by: Mike Rapoport (Microsoft) <rppt@kernel.org>
Cc: Alexander Graf <graf@amazon.com>
Cc: Changyuan Lyu <changyuanl@google.com>
Cc: Pasha Tatashin <pasha.tatashin@soleen.com>
Cc: Pratyush Yadav <pratyush@kernel.org>
Cc: Shuah Khan <shuah@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ebiggers/linux
Pull CRC updates from Eric Biggers:
- Reorganize the architecture-optimized CRC code
It now lives in lib/crc/$(SRCARCH)/ rather than arch/$(SRCARCH)/lib/,
and it is no longer artificially split into separate generic and arch
modules. This allows better inlining and dead code elimination
The generic CRC code is also no longer exported, simplifying the API.
(This mirrors the similar changes to SHA-1 and SHA-2 in lib/crypto/,
which can be found in the "Crypto library updates" pull request)
- Improve crc32c() performance on newer x86_64 CPUs on long messages by
enabling the VPCLMULQDQ optimized code
- Simplify the crypto_shash wrappers for crc32_le() and crc32c()
Register just one shash algorithm for each that uses the (fully
optimized) library functions, instead of unnecessarily providing
direct access to the generic CRC code
- Remove unused and obsolete drivers for hardware CRC engines
- Remove CRC-32 combination functions that are no longer used
- Add kerneldoc for crc32_le(), crc32_be(), and crc32c()
- Convert the crc32() macro to an inline function
* tag 'crc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiggers/linux: (26 commits)
lib/crc: x86/crc32c: Enable VPCLMULQDQ optimization where beneficial
lib/crc: x86: Reorganize crc-pclmul static_call initialization
lib/crc: crc64: Add include/linux/crc64.h to kernel-api.rst
lib/crc: crc32: Change crc32() from macro to inline function and remove cast
nvmem: layouts: Switch from crc32() to crc32_le()
lib/crc: crc32: Document crc32_le(), crc32_be(), and crc32c()
lib/crc: Explicitly include <linux/export.h>
lib/crc: Remove ARCH_HAS_* kconfig symbols
lib/crc: x86: Migrate optimized CRC code into lib/crc/
lib/crc: sparc: Migrate optimized CRC code into lib/crc/
lib/crc: s390: Migrate optimized CRC code into lib/crc/
lib/crc: riscv: Migrate optimized CRC code into lib/crc/
lib/crc: powerpc: Migrate optimized CRC code into lib/crc/
lib/crc: mips: Migrate optimized CRC code into lib/crc/
lib/crc: loongarch: Migrate optimized CRC code into lib/crc/
lib/crc: arm64: Migrate optimized CRC code into lib/crc/
lib/crc: arm: Migrate optimized CRC code into lib/crc/
lib/crc: Prepare for arch-optimized code in subdirs of lib/crc/
lib/crc: Move files into lib/crc/
lib/crc32: Remove unused combination support
...
|
|
In preparation for adding Clang sanitizer coverage stack depth tracking
that can support stack depth callbacks:
- Add the new top-level CONFIG_KSTACK_ERASE option which will be
implemented either with the stackleak GCC plugin, or with the Clang
stack depth callback support.
- Rename CONFIG_GCC_PLUGIN_STACKLEAK as needed to CONFIG_KSTACK_ERASE,
but keep it for anything specific to the GCC plugin itself.
- Rename all exposed "STACKLEAK" names and files to "KSTACK_ERASE" (named
for what it does rather than what it protects against), but leave as
many of the internals alone as possible to avoid even more churn.
While here, also split "prev_lowest_stack" into CONFIG_KSTACK_ERASE_METRICS,
since that's the only place it is referenced from.
Suggested-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20250717232519.2984886-1-kees@kernel.org
Signed-off-by: Kees Cook <kees@kernel.org>
|
|
'panic_print' was introduced to help debugging kernel panic by dumping
different kinds of system information like tasks' call stack, memory,
ftrace buffer, etc. Actually this function could also be used to help
debugging other cases like task-hung, soft/hard lockup, etc. where user
may need the snapshot of system info at that time.
Extract system info dump function related code from panic.c to separate
file sys_info.[ch], for wider usage by other kernel parts for debugging.
Also modify the macro names about singulars/plurals.
Link: https://lkml.kernel.org/r/20250703021004.42328-3-feng.tang@linux.alibaba.com
Signed-off-by: Feng Tang <feng.tang@linux.alibaba.com>
Suggested-by: Petr Mladek <pmladek@suse.com>
Cc: John Ogness <john.ogness@linutronix.de>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Lance Yang <lance.yang@linux.dev>
Cc: "Paul E . McKenney" <paulmck@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Move all CRC files in lib/ into a subdirectory lib/crc/ to keep them
from cluttering up the main lib/ directory.
Reviewed-by: "Martin K. Petersen" <martin.petersen@oracle.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Acked-by: "Jason A. Donenfeld" <Jason@zx2c4.com>
Link: https://lore.kernel.org/r/20250607200454.73587-2-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
|
|
Variable Length Arrays (VLAs) on the stack must not be used in the kernel.
Function parameter VLAs[1] should be usable, but -Wvla will warn for
those. For example, this will produce a warning but it is not using a
stack VLA:
int something(size_t n, int array[n]) { ...
Clang has no way yet to distinguish between the VLA types[2], so
depend on GCC for now to keep stack VLAs out of the tree by using GCC's
-Wvla-larger-than=N option (though GCC may split -Wvla similarly[3] to
how Clang is planning to).
While GCC 8+ supports -Wvla-larger-than, only 9+ supports ...=0[4],
so use -Wvla-larger-than=1. Adjust mm/kasan/Makefile to remove it from
CFLAGS (GCC <9 appears unable to disable the warning correctly[5]).
The VLA usage in lib/test_ubsan.c was removed in commit 9d7ca61b1366
("lib/test_ubsan.c: VLA no longer used in kernel") so the lib/Makefile
disabling of VLA checking can be entirely removed.
Link: https://en.cppreference.com/w/c/language/array [1]
Link: https://github.com/llvm/llvm-project/issues/57098 [2]
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=98217 [3]
Link: https://lore.kernel.org/lkml/7780883c-0ac8-4aaa-b850-469e33b50672@linux.ibm.com/ [4]
Link: https://lore.kernel.org/r/202505071331.4iOzqmuE-lkp@intel.com/ [5]
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Tested-by: Venkat Rao Bagalkote <venkat88@linux.ibm.com>
Link: https://lore.kernel.org/r/20250418213235.work.532-kees@kernel.org
Signed-off-by: Kees Cook <kees@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core & protocols:
- Continue Netlink conversions to per-namespace RTNL lock
(IPv4 routing, routing rules, routing next hops, ARP ioctls)
- Continue extending the use of netdev instance locks. As a driver
opt-in protect queue operations and (in due course) ethtool
operations with the instance lock and not RTNL lock.
- Support collecting TCP timestamps (data submitted, sent, acked) in
BPF, allowing for transparent (to the application) and lower
overhead tracking of TCP RPC performance.
- Tweak existing networking Rx zero-copy infra to support zero-copy
Rx via io_uring.
- Optimize MPTCP performance in single subflow mode by 29%.
- Enable GRO on packets which went thru XDP CPU redirect (were queued
for processing on a different CPU). Improving TCP stream
performance up to 2x.
- Improve performance of contended connect() by 200% by searching for
an available 4-tuple under RCU rather than a spin lock. Bring an
additional 229% improvement by tweaking hash distribution.
- Avoid unconditionally touching sk_tsflags on RX, improving
performance under UDP flood by as much as 10%.
- Avoid skb_clone() dance in ping_rcv() to improve performance under
ping flood.
- Avoid FIB lookup in netfilter if socket is available, 20% perf win.
- Rework network device creation (in-kernel) API to more clearly
identify network namespaces and their roles. There are up to 4
namespace roles but we used to have just 2 netns pointer arguments,
interpreted differently based on context.
- Use sysfs_break_active_protection() instead of trylock to avoid
deadlocks between unregistering objects and sysfs access.
- Add a new sysctl and sockopt for capping max retransmit timeout in
TCP.
- Support masking port and DSCP in routing rule matches.
- Support dumping IPv4 multicast addresses with RTM_GETMULTICAST.
- Support specifying at what time packet should be sent on AF_XDP
sockets.
- Expose TCP ULP diagnostic info (for TLS and MPTCP) to non-admin
users.
- Add Netlink YAML spec for WiFi (nl80211) and conntrack.
- Introduce EXPORT_IPV6_MOD() and EXPORT_IPV6_MOD_GPL() for symbols
which only need to be exported when IPv6 support is built as a
module.
- Age FDB entries based on Rx not Tx traffic in VxLAN, similar to
normal bridging.
- Allow users to specify source port range for GENEVE tunnels.
- netconsole: allow attaching kernel release, CPU ID and task name to
messages as metadata
Driver API:
- Continue rework / fixing of Energy Efficient Ethernet (EEE) across
the SW layers. Delegate the responsibilities to phylink where
possible. Improve its handling in phylib.
- Support symmetric OR-XOR RSS hashing algorithm.
- Support tracking and preserving IRQ affinity by NAPI itself.
- Support loopback mode speed selection for interface selftests.
Device drivers:
- Remove the IBM LCS driver for s390
- Remove the sb1000 cable modem driver
- Add support for SFP module access over SMBus
- Add MCTP transport driver for MCTP-over-USB
- Enable XDP metadata support in multiple drivers
- Ethernet high-speed NICs:
- Broadcom (bnxt):
- add PCIe TLP Processing Hints (TPH) support for new AMD
platforms
- support dumping RoCE queue state for debug
- opt into instance locking
- Intel (100G, ice, idpf):
- ice: rework MSI-X IRQ management and distribution
- ice: support for E830 devices
- iavf: add support for Rx timestamping
- iavf: opt into instance locking
- nVidia/Mellanox:
- mlx4: use page pool memory allocator for Rx
- mlx5: support for one PTP device per hardware clock
- mlx5: support for 200Gbps per-lane link modes
- mlx5: move IPSec policy check after decryption
- AMD/Solarflare:
- support FW flashing via devlink
- Cisco (enic):
- use page pool memory allocator for Rx
- enable 32, 64 byte CQEs
- get max rx/tx ring size from the device
- Meta (fbnic):
- support flow steering and RSS configuration
- report queue stats
- support TCP segmentation
- support IRQ coalescing
- support ring size configuration
- Marvell/Cavium:
- support AF_XDP
- Wangxun:
- support for PTP clock and timestamping
- Huawei (hibmcge):
- checksum offload
- add more statistics
- Ethernet virtual:
- VirtIO net:
- aggressively suppress Tx completions, improve perf by 96%
with 1 CPU and 55% with 2 CPUs
- expose NAPI to IRQ mapping and persist NAPI settings
- Google (gve):
- support XDP in DQO RDA Queue Format
- opt into instance locking
- Microsoft vNIC:
- support BIG TCP
- Ethernet NICs consumer, and embedded:
- Synopsys (stmmac):
- cleanup Tx and Tx clock setting and other link-focused
cleanups
- enable SGMII and 2500BASEX mode switching for Intel platforms
- support Sophgo SG2044
- Broadcom switches (b53):
- support for BCM53101
- TI:
- iep: add perout configuration support
- icssg: support XDP
- Cadence (macb):
- implement BQL
- Xilinx (axinet):
- support dynamic IRQ moderation and changing coalescing at
runtime
- implement BQL
- report standard stats
- MediaTek:
- support phylink managed EEE
- Intel:
- igc: don't restart the interface on every XDP program change
- RealTek (r8169):
- support reading registers of internal PHYs directly
- increase max jumbo packet size on RTL8125/RTL8126
- Airoha:
- support for RISC-V NPU packet processing unit
- enable scatter-gather and support MTU up to 9kB
- Tehuti (tn40xx):
- support cards with TN4010 MAC and an Aquantia AQR105 PHY
- Ethernet PHYs:
- support for TJA1102S, TJA1121
- dp83tg720: add randomized polling intervals for link detection
- dp83822: support changing the transmit amplitude voltage
- support for LEDs on 88q2xxx
- CAN:
- canxl: support Remote Request Substitution bit access
- flexcan: add S32G2/S32G3 SoC
- WiFi:
- remove cooked monitor support
- strict mode for better AP testing
- basic EPCS support
- OMI RX bandwidth reduction support
- batman-adv: add support for jumbo frames
- WiFi drivers:
- RealTek (rtw88):
- support RTL8814AE and RTL8814AU
- RealTek (rtw89):
- switch using wiphy_lock and wiphy_work
- add BB context to manipulate two PHY as preparation of MLO
- improve BT-coexistence mechanism to play A2DP smoothly
- Intel (iwlwifi):
- add new iwlmld sub-driver for latest HW/FW combinations
- MediaTek (mt76):
- preparation for mt7996 Multi-Link Operation (MLO) support
- Qualcomm/Atheros (ath12k):
- continued work on MLO
- Silabs (wfx):
- Wake-on-WLAN support
- Bluetooth:
- add support for skb TX SND/COMPLETION timestamping
- hci_core: enable buffer flow control for SCO/eSCO
- coredump: log devcd dumps into the monitor
- Bluetooth drivers:
- intel: add support to configure TX power
- nxp: handle bootloader error during cmd5 and cmd7"
* tag 'net-next-6.15' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1681 commits)
unix: fix up for "apparmor: add fine grained af_unix mediation"
mctp: Fix incorrect tx flow invalidation condition in mctp-i2c
net: usb: asix: ax88772: Increase phy_name size
net: phy: Introduce PHY_ID_SIZE — minimum size for PHY ID string
net: libwx: fix Tx L4 checksum
net: libwx: fix Tx descriptor content for some tunnel packets
atm: Fix NULL pointer dereference
net: tn40xx: add pci-id of the aqr105-based Tehuti TN4010 cards
net: tn40xx: prepare tn40xx driver to find phy of the TN9510 card
net: tn40xx: create swnode for mdio and aqr105 phy and add to mdiobus
net: phy: aquantia: add essential functions to aqr105 driver
net: phy: aquantia: search for firmware-name in fwnode
net: phy: aquantia: add probe function to aqr105 for firmware loading
net: phy: Add swnode support to mdiobus_scan
gve: add XDP DROP and PASS support for DQ
gve: update XDP allocation path support RX buffer posting
gve: merge packet buffer size fields
gve: update GQ RX to use buf_size
gve: introduce config-based allocation for XDP
gve: remove xdp_xsk_done and xdp_xsk_wakeup statistics
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ebiggers/linux
Pull CRC updates from Eric Biggers:
"Another set of improvements to the kernel's CRC (cyclic redundancy
check) code:
- Rework the CRC64 library functions to be directly optimized, like
what I did last cycle for the CRC32 and CRC-T10DIF library
functions
- Rewrite the x86 PCLMULQDQ-optimized CRC code, and add VPCLMULQDQ
support and acceleration for crc64_be and crc64_nvme
- Rewrite the riscv Zbc-optimized CRC code, and add acceleration for
crc_t10dif, crc64_be, and crc64_nvme
- Remove crc_t10dif and crc64_rocksoft from the crypto API, since
they are no longer needed there
- Rename crc64_rocksoft to crc64_nvme, as the old name was incorrect
- Add kunit test cases for crc64_nvme and crc7
- Eliminate redundant functions for calculating the Castagnoli CRC32,
settling on just crc32c()
- Remove unnecessary prompts from some of the CRC kconfig options
- Further optimize the x86 crc32c code"
* tag 'crc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiggers/linux: (36 commits)
x86/crc: drop the avx10_256 functions and rename avx10_512 to avx512
lib/crc: remove unnecessary prompt for CONFIG_CRC64
lib/crc: remove unnecessary prompt for CONFIG_LIBCRC32C
lib/crc: remove unnecessary prompt for CONFIG_CRC8
lib/crc: remove unnecessary prompt for CONFIG_CRC7
lib/crc: remove unnecessary prompt for CONFIG_CRC4
lib/crc7: unexport crc7_be_syndrome_table
lib/crc_kunit.c: update comment in crc_benchmark()
lib/crc_kunit.c: add test and benchmark for crc7_be()
x86/crc32: optimize tail handling for crc32c short inputs
riscv/crc64: add Zbc optimized CRC64 functions
riscv/crc-t10dif: add Zbc optimized CRC-T10DIF function
riscv/crc32: reimplement the CRC32 functions using new template
riscv/crc: add "template" for Zbc optimized CRC functions
x86/crc: add ANNOTATE_NOENDBR to suppress objtool warnings
x86/crc32: improve crc32c_arch() code generation with clang
x86/crc64: implement crc64_be and crc64_nvme using new template
x86/crc-t10dif: implement crc_t10dif using new template
x86/crc32: implement crc32_le using new template
x86/crc: add "template" for [V]PCLMULQDQ based CRC functions
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull VDSO infrastructure updates from Thomas Gleixner:
- Consolidate the VDSO storage
The VDSO data storage and data layout has been largely architecture
specific for historical reasons. That increases the maintenance
effort and causes inconsistencies over and over.
There is no real technical reason for architecture specific layouts
and implementations. The architecture specific details can easily be
integrated into a generic layout, which also reduces the amount of
duplicated code for managing the mappings.
Convert all architectures over to a unified layout and common mapping
infrastructure. This splits the VDSO data layout into subsystem
specific blocks, timekeeping, random and architecture parts, which
provides a better structure and allows to improve and update the
functionalities without conflict and interaction.
- Rework the timekeeping data storage
The current implementation is designed for exposing system
timekeeping accessors, which was good enough at the time when it was
designed.
PTP and Time Sensitive Networking (TSN) change that as there are
requirements to expose independent PTP clocks, which are not related
to system timekeeping.
Replace the monolithic data storage by a structured layout, which
allows to add support for independent PTP clocks on top while reusing
both the data structures and the time accessor implementations.
* tag 'timers-vdso-2025-03-23' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (55 commits)
sparc/vdso: Always reject undefined references during linking
x86/vdso: Always reject undefined references during linking
vdso: Rework struct vdso_time_data and introduce struct vdso_clock
vdso: Move architecture related data before basetime data
powerpc/vdso: Prepare introduction of struct vdso_clock
arm64/vdso: Prepare introduction of struct vdso_clock
x86/vdso: Prepare introduction of struct vdso_clock
time/namespace: Prepare introduction of struct vdso_clock
vdso/namespace: Rename timens_setup_vdso_data() to reflect new vdso_clock struct
vdso/vsyscall: Prepare introduction of struct vdso_clock
vdso/gettimeofday: Prepare helper functions for introduction of struct vdso_clock
vdso/gettimeofday: Prepare do_coarse_timens() for introduction of struct vdso_clock
vdso/gettimeofday: Prepare do_coarse() for introduction of struct vdso_clock
vdso/gettimeofday: Prepare do_hres_timens() for introduction of struct vdso_clock
vdso/gettimeofday: Prepare do_hres() for introduction of struct vdso_clock
vdso/gettimeofday: Prepare introduction of struct vdso_clock
vdso/helpers: Prepare introduction of struct vdso_clock
vdso/datapage: Define vdso_clock to prepare for multiple PTP clocks
vdso: Make vdso_time_data cacheline aligned
arm64: Make asm/cache.h compatible with vDSO
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull objtool updates from Ingo Molnar:
- The biggest change is the new option to automatically fail the build
on objtool warnings: CONFIG_OBJTOOL_WERROR.
While there are no currently known unfixed false positives left, such
an expansion in the severity of objtool warnings inevitably creates a
risk of build failures, so it's disabled by default and depends on
!COMPILE_TEST, so it shouldn't be enabled on
allyesconfig/allmodconfig builds and won't be forced on people who
just accept build-time defaults in 'make oldconfig'.
While the option is strongly recommended, only people who enable it
explicitly should see it.
(Josh Poimboeuf)
- Disable branch profiling in noinstr code with a broad brush that
includes all of arch/x86/ and kernel/sched/. (Josh Poimboeuf)
- Create backup object files on objtool errors and print exact objtool
arguments to make failure analysis easier (Josh Poimboeuf)
- Improve noreturn handling (Josh Poimboeuf)
- Improve rodata handling (Tiezhu Yang)
- Support jump tables, switch tables and goto tables on LoongArch
(Tiezhu Yang)
- Misc cleanups and fixes (Josh Poimboeuf, David Engraf, Ingo Molnar)
* tag 'objtool-core-2025-03-22' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (22 commits)
tracing: Disable branch profiling in noinstr code
objtool: Use O_CREAT with explicit mode mask
objtool: Add CONFIG_OBJTOOL_WERROR
objtool: Create backup on error and print args
objtool: Change "warning:" to "error:" for --Werror
objtool: Add --Werror option
objtool: Add --output option
objtool: Upgrade "Linked object detected" warning to error
objtool: Consolidate option validation
objtool: Remove --unret dependency on --rethunk
objtool: Increase per-function WARN_FUNC() rate limit
objtool: Update documentation
objtool: Improve __noreturn annotation warning
objtool: Fix error handling inconsistencies in check()
x86/traps: Make exc_double_fault() consistently noreturn
LoongArch: Enable jump table for objtool
objtool/LoongArch: Add support for goto table
objtool/LoongArch: Add support for switch table
objtool: Handle PC relative relocation type
objtool: Handle different entry size of rodata
...
|
|
CONFIG_TRACE_BRANCH_PROFILING inserts a call to ftrace_likely_update()
for each use of likely() or unlikely(). That breaks noinstr rules if
the affected function is annotated as noinstr.
Disable branch profiling for files with noinstr functions. In addition
to some individual files, this also includes the entire arch/x86
subtree, as well as the kernel/entry, drivers/cpuidle, and drivers/idle
directories, all of which are noinstr-heavy.
Due to the nature of how sched binaries are built by combining multiple
.c files into one, branch profiling is disabled more broadly across the
sched code than would otherwise be needed.
This fixes many warnings like the following:
vmlinux.o: warning: objtool: do_syscall_64+0x40: call to ftrace_likely_update() leaves .noinstr.text section
vmlinux.o: warning: objtool: __rdgsbase_inactive+0x33: call to ftrace_likely_update() leaves .noinstr.text section
vmlinux.o: warning: objtool: handle_bug.isra.0+0x198: call to ftrace_likely_update() leaves .noinstr.text section
...
Reported-by: Ingo Molnar <mingo@kernel.org>
Suggested-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: https://lore.kernel.org/r/fb94fc9303d48a5ed370498f54500cc4c338eb6d.1742586676.git.jpoimboe@kernel.org
|
|
Convert the scanf() self-test to a KUnit test.
In the interest of keeping the patch reasonably-sized this doesn't
refactor the tests into proper parameterized tests - it's all one big
test case.
Reviewed-by: David Gow <davidgow@google.com>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Tested-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Tamir Duberstein <tamird@gmail.com>
Link: https://lore.kernel.org/r/20250307-scanf-kunit-convert-v9-3-b98820fa39ff@gmail.com
Signed-off-by: Kees Cook <kees@kernel.org>
|
|
Convert the printf() self-test to a KUnit test.
In the interest of keeping the patch reasonably-sized this doesn't
refactor the tests into proper parameterized tests - it's all one big
test case.
Signed-off-by: Tamir Duberstein <tamird@gmail.com>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Tested-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20250307-printf-kunit-convert-v6-1-4d85c361c241@gmail.com
Signed-off-by: Kees Cook <kees@kernel.org>
|
|
Historically each architecture defined their own way to store the vDSO
data page. Add a generic mechanism to provide storage for that page.
Furthermore this generic storage will be extended to also provide
uniform storage for *non*-time-related data, like the random state or
architecture-specific data. These will have their own pages and data
structures, so rename 'vdso_data' into 'vdso_time_data' to make that
split clear from the name.
Also introduce a new consistent naming scheme for the symbols related to
the vDSO, which makes it clear if the symbol is accessible from
userspace or kernel space and the type of data behind the symbol.
The generic fault handler contains an optimization to prefault the vvar
page when the timens page is accessed. This was lifted from s390 and x86.
Co-developed-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250204-vdso-store-rng-v3-5-13a4669dfc8c@linutronix.de
|
|
Convert this very simple smoke test to a KUnit test.
Add a missing `htons` call that was spotted[0] by kernel test robot
<lkp@intel.com> after initial conversion to KUnit.
Link: https://lore.kernel.org/oe-kbuild-all/202502090223.qCYMBjWT-lkp@intel.com/ [0]
Signed-off-by: Tamir Duberstein <tamird@gmail.com>
Link: https://patch.msgid.link/20250208-blackholedev-kunit-convert-v2-1-182db9bd56ec@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Following from the recent KUnit file naming discussion[1], move all
KUnit tests in lib/ into lib/tests/.
Link: https://lore.kernel.org/lkml/20240720165441.it.320-kees@kernel.org/ [1]
Acked-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Reviewed-by: David Gow <davidgow@google.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Reviewed-by: Rae Moar <rmoar@google.com>
Link: https://lore.kernel.org/r/20241202075545.3648096-4-davidgow@google.com
Signed-off-by: Kees Cook <kees@kernel.org>
|
|
Following what was done for the CRC32 and CRC-T10DIF library functions,
get rid of the pointless use of the crypto API and make
crc64_rocksoft_update() call into the library directly. This is faster
and simpler.
Remove crc64_rocksoft() (the version of the function that did not take a
'crc' argument) since it is unused.
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: "Martin K. Petersen" <martin.petersen@oracle.com>
Acked-by: Keith Busch <kbusch@kernel.org>
Link: https://lore.kernel.org/r/20250130035130.180676-2-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
|
|
Revert c7bb5cf9fc4e ("xarray: port tests to kunit"). It broke the build
when compiing the xarray userspace test harness code.
Reported-by: Sidhartha Kumar <sidhartha.kumar@oracle.com>
Closes: https://lkml.kernel.org/r/07cf896e-adf8-414f-a629-a808fc26014a@oracle.com
Cc: David Gow <davidgow@google.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Tamir Duberstein <tamird@gmail.com>
Cc: "Liam R. Howlett" <Liam.Howlett@oracle.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull non-MM updates from Andrew Morton:
"Mainly individually changelogged singleton patches. The patch series
in this pull are:
- "lib min_heap: Improve min_heap safety, testing, and documentation"
from Kuan-Wei Chiu provides various tightenings to the min_heap
library code
- "xarray: extract __xa_cmpxchg_raw" from Tamir Duberstein preforms
some cleanup and Rust preparation in the xarray library code
- "Update reference to include/asm-<arch>" from Geert Uytterhoeven
fixes pathnames in some code comments
- "Converge on using secs_to_jiffies()" from Easwar Hariharan uses
the new secs_to_jiffies() in various places where that is
appropriate
- "ocfs2, dlmfs: convert to the new mount API" from Eric Sandeen
switches two filesystems to the new mount API
- "Convert ocfs2 to use folios" from Matthew Wilcox does that
- "Remove get_task_comm() and print task comm directly" from Yafang
Shao removes now-unneeded calls to get_task_comm() in various
places
- "squashfs: reduce memory usage and update docs" from Phillip
Lougher implements some memory savings in squashfs and performs
some maintainability work
- "lib: clarify comparison function requirements" from Kuan-Wei Chiu
tightens the sort code's behaviour and adds some maintenance work
- "nilfs2: protect busy buffer heads from being force-cleared" from
Ryusuke Konishi fixes an issues in nlifs when the fs is presented
with a corrupted image
- "nilfs2: fix kernel-doc comments for function return values" from
Ryusuke Konishi fixes some nilfs kerneldoc
- "nilfs2: fix issues with rename operations" from Ryusuke Konishi
addresses some nilfs BUG_ONs which syzbot was able to trigger
- "minmax.h: Cleanups and minor optimisations" from David Laight does
some maintenance work on the min/max library code
- "Fixes and cleanups to xarray" from Kemeng Shi does maintenance
work on the xarray library code"
* tag 'mm-nonmm-stable-2025-01-24-23-16' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (131 commits)
ocfs2: use str_yes_no() and str_no_yes() helper functions
include/linux/lz4.h: add some missing macros
Xarray: use xa_mark_t in xas_squash_marks() to keep code consistent
Xarray: remove repeat check in xas_squash_marks()
Xarray: distinguish large entries correctly in xas_split_alloc()
Xarray: move forward index correctly in xas_pause()
Xarray: do not return sibling entries from xas_find_marked()
ipc/util.c: complete the kernel-doc function descriptions
gcov: clang: use correct function param names
latencytop: use correct kernel-doc format for func params
minmax.h: remove some #defines that are only expanded once
minmax.h: simplify the variants of clamp()
minmax.h: move all the clamp() definitions after the min/max() ones
minmax.h: use BUILD_BUG_ON_MSG() for the lo < hi test in clamp()
minmax.h: reduce the #define expansion of min(), max() and clamp()
minmax.h: update some comments
minmax.h: add whitespace around operators and after commas
nilfs2: do not update mtime of renamed directory that is not moved
nilfs2: handle errors that nilfs_prepare_chunk() may return
CREDITS: fix spelling mistake
...
|
|
Minimally rewrite the XArray unit tests to use kunit. This integrates
nicely with existing kunit tools which produce nicer human-readable output
compared to the existing machinery.
Running the xarray tests before this change requires an obscure
invocation
```
tools/testing/kunit/kunit.py run --arch arm64 --make_options LLVM=1 \
--kconfig_add CONFIG_TEST_XARRAY=y --raw_output=all nothing
```
which on failure produces
```
BUG at check_reserve:513
...
XArray: 6782340 of 6782364 tests passed
```
and exits 0.
Running the xarray tests after this change requires a simpler invocation
```
tools/testing/kunit/kunit.py run --arch arm64 --make_options LLVM=1 \
xarray
```
which on failure produces (colors omitted)
```
[09:50:53] ====================== check_reserve ======================
[09:50:53] [FAILED] param-0
[09:50:53] # check_reserve: EXPECTATION FAILED at lib/test_xarray.c:536
[09:50:53] xa_erase(xa, 12345678) != NULL
...
[09:50:53] # module: test_xarray
[09:50:53] # xarray: pass:26 fail:3 skip:0 total:29
[09:50:53] # Totals: pass:28 fail:3 skip:0 total:31
[09:50:53] ===================== [FAILED] xarray ======================
```
and exits 1.
Use of richer kunit assertions is intentionally omitted to reduce the
scope of the change.
[akpm@linux-foundation.org: fix cocci warning]
Link: https://lore.kernel.org/oe-kbuild-all/202412081700.YXB3vBbg-lkp@intel.com/
Link: https://lkml.kernel.org/r/20241205-xarray-kunit-port-v1-1-ee44bc7aa201@gmail.com
Signed-off-by: Tamir Duberstein <tamird@gmail.com>
Cc: Bill Wendling <morbo@google.com>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Justin Stitt <justinstitt@google.com>
Cc: Madhavan Srinivasan <maddy@linux.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Naveen N Rao <naveen@kernel.org>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Delete crc32test.c, since it has been superseded by crc_kunit.c.
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> # m68k
Cc: Vinicius Peixoto <vpeixoto@lkcamp.dev>
Link: https://lore.kernel.org/r/20241202012056.209768-11-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
|
|
This new test showed up in v6.13-rc1. Delete it since it is being
superseded by crc_kunit.c, which is more comprehensive (tests multiple
CRC variants without duplicating code, includes a benchmark, etc.).
Cc: Vinicius Peixoto <vpeixoto@lkcamp.dev>
Link: https://lore.kernel.org/r/20241202012056.209768-10-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
|
|
Add a KUnit test suite for the crc16, crc_t10dif, crc32_le, crc32_be,
crc32c, and crc64_be library functions. It avoids code duplication by
sharing most logic among all CRC variants. The test suite includes:
- Differential fuzz test of each CRC function against a simple
bit-at-a-time reference implementation.
- Test for CRC combination, when implemented by a CRC variant.
- Optional benchmark of each CRC function with various data lengths.
This is intended as a replacement for crc32test and crc16_kunit, as well
as a new test for CRC variants which didn't previously have a test.
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Martin K. Petersen &l |
