| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull MSI updates from Thomas Gleixner:
"Updates for the [PCI] MSI subsystem:
- Add interrupt redirection infrastructure
Some PCI controllers use a single demultiplexing interrupt for the
MSI interrupts of subordinate devices.
This prevents setting the interrupt affinity of device interrupts,
which causes device interrupts to be delivered to a single CPU.
That obviously is counterproductive for multi-queue devices and
interrupt balancing.
To work around this limitation the new infrastructure installs a
dummy irq_set_affinity() callback which captures the affinity mask
and picks a redirection target CPU out of the mask.
When the PCI controller demultiplexes the interrupts it invokes a
new handling function in the core, which either runs the interrupt
handler in the context of the target CPU or delegates it to
irq_work on the target CPU.
- Utilize the interrupt redirection mechanism in the PCI DWC host
controller driver.
This allows affinity control for the subordinate device MSI
interrupts instead of being randomly executed on the CPU which runs
the demultiplex handler.
- Replace the binary 64-bit MSI flag with a DMA mask
Some PCI devices have PCI_MSI_FLAGS_64BIT in the MSI capability,
but implement less than 64 address bits. This breaks on platforms
where such a device is assigned an MSI address higher than what's
supported.
With the binary 64-bit flag there is no other choice than disabling
64-bit MSI support which leaves the device disfunctional.
By using a DMA mask the address limit of a device can be described
correctly which provides support for the above scenario.
- Make use of the DMA mask based address limit in the hda/intel and
radeon drivers to enable them on affected platforms
- The usual small cleanups and improvements"
* tag 'irq-msi-2026-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
ALSA: hda/intel: Make MSI address limit based on the device DMA limit
drm/radeon: Make MSI address limit based on the device DMA limit
PCI/MSI: Check the device specific address mask in msi_verify_entries()
PCI/MSI: Convert the boolean no_64bit_msi flag to a DMA address mask
genirq/redirect: Prevent writing MSI message on affinity change
PCI/MSI: Unmap MSI-X region on error
genirq: Update effective affinity for redirected interrupts
PCI: dwc: Enable MSI affinity support
PCI: dwc: Code cleanup
genirq: Add interrupt redirection infrastructure
genirq/msi: Correct kernel-doc in <linux/msi.h>
|
|
To support booting with OF and ACPI seamlessly, GIC ITS parent code
requires the PCI/MSI irqdomain layer to implement a function to retrieve
an MSI controller fwnode and map an RID in a firmware agnostic way
(ie pci_msi_map_rid_ctlr_node()).
Convert pci_msi_map_rid_ctlr_node() to an OF agnostic interface
(fwnode_handle based) and update the GIC ITS MSI parent code to reflect
the pci_msi_map_rid_ctlr_node() change.
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@kernel.org>
Link: https://patch.msgid.link/20260115-gicv5-host-acpi-v3-2-c13a9a150388@kernel.org
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Eliminate all kernel-doc warnings in <linux/msi.h>:
- add "struct" to struct kernel-doc headers
- add missing struct member descriptions or correct typos in them
Fixes these warnings:
Warning: include/linux/msi.h:60 cannot understand function prototype:
'struct msi_msg'
Warning: include/linux/msi.h:73 struct member 'arch_addr_lo' not described
in 'msi_msg'
Warning: include/linux/msi.h:73 struct member 'arch_addr_hi' not described
in 'msi_msg'
Warning: include/linux/msi.h:106 cannot understand function prototype:
'struct pci_msi_desc'
Warning: include/linux/msi.h:124 struct member 'msi_attrib' not described
in 'pci_msi_desc'
Warning: include/linux/msi.h:204 struct member 'sysfs_attrs' not described
in 'msi_desc'
Warning: include/linux/msi.h:227 struct member 'domain' not described in
'msi_dev_domain'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://patch.msgid.link/20251214202341.2205675-1-rdunlap@infradead.org
|
|
pci_msi_create_irq_domain() is now unused. Delete it.
Signed-off-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq chip driver updates from Thomas Gleixner:
- Use the startup/shutdown callbacks for the PCI/MSI per device
interrupt domains.
This allows us to initialize the RISCV PLIC interrupt hierarchy
correctly and provides a mechanism to decouple the masking and
unmasking during run-time from the expensive PCI mask and unmask when
the underlying MSI provider implementation allows the interrupt to be
masked.
- Initialize the RISCV PLIC MSI interrupt hierarchy correctly so that
the affinity assignment works correctly by switching it over to the
startup/shutdown scheme
- Allow MSI providers to opt out from masking a PCI/MSI interrupt at
the PCI device during operation when the provider can mask the
interrupt at the underlying interrupt chip. This reduces the overhead
in scenarios where disable_irq()/enable_irq() is utilized frequently
by a driver.
The PCI/MSI device level [un]masking is only required on startup and
shutdown in this case.
- Remove the conditional mask/unmask logic in the PCI/MSI layer as this
is now handled unconditionally.
- Replace the hardcoded interrupt routing in the Loongson EIOINTC
interrupt driver to respect the firmware settings and spread them out
to different CPU interrupt inputs so that the demultiplexing handler
only needs to read only a single 64-bit status register instead of
four, which significantly reduces the overhead in VMs as the status
register access causes a VM exit.
- Add support for the new AST2700 SCU interrupt controllers
- Use the legacy interrupt domain setup for the Loongson PCH-LPC
interrupt controller, which resembles the x86 legacy PIC setup and
has the same hardcoded legacy requirements.
- The usual set of cleanups, fixes and improvements all over the place
* tag 'irq-drivers-2025-09-29' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (25 commits)
irqchip/loongson-pch-lpc: Use legacy domain for PCH-LPC IRQ controller
PCI/MSI: Remove the conditional parent [un]mask logic
irqchip/msi-lib: Honor the MSI_FLAG_PCI_MSI_MASK_PARENT flag
irqchip/aspeed-scu-ic: Add support for AST2700 SCU interrupt controllers
dt-bindings: interrupt-controller: aspeed: Add AST2700 SCU IC compatibles
dt-bindings: mfd: aspeed: Add AST2700 SCU compatibles
irqchip/aspeed-scu-ic: Refactor driver to support variant-based initialization
irqchip/gic-v5: Fix error handling in gicv5_its_irq_domain_alloc()
irqchip/gic-v5: Fix loop in gicv5_its_create_itt_two_level() cleanup path
irqchip/gic-v5: Delete a stray tab
irqchip/sg2042-msi: Set irq type according to DT configuration
riscv: sophgo: dts: sg2044: Change msi irq type to IRQ_TYPE_EDGE_RISING
riscv: sophgo: dts: sg2042: Change msi irq type to IRQ_TYPE_EDGE_RISING
irqchip/gic-v2m: Handle Multiple MSI base IRQ Alignment
irqchip/renesas-rzg2l: Remove dev_err_probe() if error is -ENOMEM
irqchip: Use int type to store negative error codes
irqchip/gic-v5: Remove the redundant ITS cache invalidation
PCI/MSI: Check MSI_FLAG_PCI_MSI_MASK_PARENT in cond_[startup|shutdown]_parent()
irqchip/loongson-eiointc: Add multiple interrupt pin routing support
irqchip/loongson-eiointc: Route interrupt parsed from bios table
...
|
|
The only user of msi_post_free() - powerpc/pseries - has been changed to
use msi_teardown().
Remove this unused callback.
Signed-off-by: Nam Cao <namcao@linutronix.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Link: https://patch.msgid.link/20250916061007.964005-1-namcao@linutronix.de
|
|
As the RISC-V PLIC cannot apply affinity settings without invoking
irq_enable(), it will make the interrupt unavailble when used as an
underlying interrupt chip for the MSI controller.
Implement the irq_startup() and irq_shutdown() callbacks for the PCI MSI
and MSI-X templates.
For chips that specify MSI_FLAG_PCI_MSI_STARTUP_PARENT, the parent startup
and shutdown functions are invoked. That allows the interrupt on the parent
chip to be enabled if the interrupt has not been enabled during
allocation. This is necessary for MSI controllers which use PLIC as
underlying parent interrupt chip.
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Inochi Amaoto <inochiama@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Chen Wang <unicorn_wang@outlook.com> # Pioneerbox
Reviewed-by: Chen Wang <unicorn_wang@outlook.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/all/20250813232835.43458-3-inochiama@gmail.com
|
|
Pull kvm updates from Paolo Bonzini:
"ARM:
- Host driver for GICv5, the next generation interrupt controller for
arm64, including support for interrupt routing, MSIs, interrupt
translation and wired interrupts
- Use FEAT_GCIE_LEGACY on GICv5 systems to virtualize GICv3 VMs on
GICv5 hardware, leveraging the legacy VGIC interface
- Userspace control of the 'nASSGIcap' GICv3 feature, allowing
userspace to disable support for SGIs w/o an active state on
hardware that previously advertised it unconditionally
- Map supporting endpoints with cacheable memory attributes on
systems with FEAT_S2FWB and DIC where KVM no longer needs to
perform cache maintenance on the address range
- Nested support for FEAT_RAS and FEAT_DoubleFault2, allowing the
guest hypervisor to inject external aborts into an L2 VM and take
traps of masked external aborts to the hypervisor
- Convert more system register sanitization to the config-driven
implementation
- Fixes to the visibility of EL2 registers, namely making VGICv3
system registers accessible through the VGIC device instead of the
ONE_REG vCPU ioctls
- Various cleanups and minor fixes
LoongArch:
- Add stat information for in-kernel irqchip
- Add tracepoints for CPUCFG and CSR emulation exits
- Enhance in-kernel irqchip emulation
- Various cleanups
RISC-V:
- Enable ring-based dirty memory tracking
- Improve perf kvm stat to report interrupt events
- Delegate illegal instruction trap to VS-mode
- MMU improvements related to upcoming nested virtualization
s390x
- Fixes
x86:
- Add CONFIG_KVM_IOAPIC for x86 to allow disabling support for I/O
APIC, PIC, and PIT emulation at compile time
- Share device posted IRQ code between SVM and VMX and harden it
against bugs and runtime errors
- Use vcpu_idx, not vcpu_id, for GA log tag/metadata, to make lookups
O(1) instead of O(n)
- For MMIO stale data mitigation, track whether or not a vCPU has
access to (host) MMIO based on whether the page tables have MMIO
pfns mapped; using VFIO is prone to false negatives
- Rework the MSR interception code so that the SVM and VMX APIs are
more or less identical
- Recalculate all MSR intercepts from scratch on MSR filter changes,
instead of maintaining shadow bitmaps
- Advertise support for LKGS (Load Kernel GS base), a new instruction
that's loosely related to FRED, but is supported and enumerated
independently
- Fix a user-triggerable WARN that syzkaller found by setting the
vCPU in INIT_RECEIVED state (aka wait-for-SIPI), and then putting
the vCPU into VMX Root Mode (post-VMXON). Trying to detect every
possible path leading to architecturally forbidden states is hard
and even risks breaking userspace (if it goes from valid to valid
state but passes through invalid states), so just wait until
KVM_RUN to detect that the vCPU state isn't allowed
- Add KVM_X86_DISABLE_EXITS_APERFMPERF to allow disabling
interception of APERF/MPERF reads, so that a "properly" configured
VM can access APERF/MPERF. This has many caveats (APERF/MPERF
cannot be zeroed on vCPU creation or saved/restored on suspend and
resume, or preserved over thread migration let alone VM migration)
but can be useful whenever you're interested in letting Linux
guests see the effective physical CPU frequency in /proc/cpuinfo
- Reject KVM_SET_TSC_KHZ for vm file descriptors if vCPUs have been
created, as there's no known use case for changing the default
frequency for other VM types and it goes counter to the very reason
why the ioctl was added to the vm file descriptor. And also, there
would be no way to make it work for confidential VMs with a
"secure" TSC, so kill two birds with one stone
- Dynamically allocation the shadow MMU's hashed page list, and defer
allocating the hashed list until it's actually needed (the TDP MMU
doesn't use the list)
- Extract many of KVM's helpers for accessing architectural local
APIC state to common x86 so that they can be shared by guest-side
code for Secure AVIC
- Various cleanups and fixes
x86 (Intel):
- Preserve the host's DEBUGCTL.FREEZE_IN_SMM when running the guest.
Failure to honor FREEZE_IN_SMM can leak host state into guests
- Explicitly check vmcs12.GUEST_DEBUGCTL on nested VM-Enter to
prevent L1 from running L2 with features that KVM doesn't support,
e.g. BTF
x86 (AMD):
- WARN and reject loading kvm-amd.ko instead of panicking the kernel
if the nested SVM MSRPM offsets tracker can't handle an MSR (which
is pretty much a static condition and therefore should never
happen, but still)
- Fix a variety of flaws and bugs in the AVIC device posted IRQ code
- Inhibit AVIC if a vCPU's ID is too big (relative to what hardware
supports) instead of rejecting vCPU creation
- Extend enable_ipiv module param support to SVM, by simply leaving
IsRunning clear in the vCPU's physical ID table entry
- Disable IPI virtualization, via enable_ipiv, if the CPU is affected
by erratum #1235, to allow (safely) enabling AVIC on such CPUs
- Request GA Log interrupts if and only if the target vCPU is
blocking, i.e. only if KVM needs a notification in order to wake
the vCPU
- Intercept SPEC_CTRL on AMD if the MSR shouldn't exist according to
the vCPU's CPUID model
- Accept any SNP policy that is accepted by the firmware with respect
to SMT and single-socket restrictions. An incompatible policy
doesn't put the kernel at risk in any way, so there's no reason for
KVM to care
- Drop a superfluous WBINVD (on all CPUs!) when destroying a VM and
use WBNOINVD instead of WBINVD when possible for SEV cache
maintenance
- When reclaiming memory from an SEV guest, only do cache flushes on
CPUs that have ever run a vCPU for the guest, i.e. don't flush the
caches for CPUs that can't possibly have cache lines with dirty,
encrypted data
Generic:
- Rework irqbypass to track/match producers and consumers via an
xarray instead of a linked list. Using a linked list leads to
O(n^2) insertion times, which is hugely problematic for use cases
that create large numbers of VMs. Such use cases typically don't
actually use irqbypass, but eliminating the pointless registration
is a future problem to solve as it likely requires new uAPI
- Track irqbypass's "token" as "struct eventfd_ctx *" instead of a
"void *", to avoid making a simple concept unnecessarily difficult
to understand
- Decouple device posted IRQs from VFIO device assignment, as binding
a VM to a VFIO group is not a requirement for enabling device
posted IRQs
- Clean up and document/comment the irqfd assignment code
- Disallow binding multiple irqfds to an eventfd with a priority
waiter, i.e. ensure an eventfd is bound to at most one irqfd
through the entire host, and add a selftest to verify eventfd:irqfd
bindings are globally unique
- Add a tracepoint for KVM_SET_MEMORY_ATTRIBUTES to help debug issues
related to private <=> shared memory conversions
- Drop guest_memfd's .getattr() implementation as the VFS layer will
call generic_fillattr() if inode_operations.getattr is NULL
- Fix issues with dirty ring harvesting where KVM doesn't bound the
processing of entries in any way, which allows userspace to keep
KVM in a tight loop indefinitely
- Kill off kvm_arch_{start,end}_assignment() and x86's associated
tracking, now that KVM no longer uses assigned_device_count as a
heuristic for either irqbypass usage or MDS mitigation
Selftests:
- Fix a comment typo
- Verify KVM is loaded when getting any KVM module param so that
attempting to run a selftest without kvm.ko loaded results in a
SKIP message about KVM not being loaded/enabled (versus some random
parameter not existing)
- Skip tests that hit EACCES when attempting to access a file, and
print a "Root required?" help message. In most cases, the test just
needs to be run with elevated permissions"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (340 commits)
Documentation: KVM: Use unordered list for pre-init VGIC registers
RISC-V: KVM: Avoid re-acquiring memslot in kvm_riscv_gstage_map()
RISC-V: KVM: Use find_vma_intersection() to search for intersecting VMAs
RISC-V: perf/kvm: Add reporting of interrupt events
RISC-V: KVM: Enable ring-based dirty memory tracking
RISC-V: KVM: Fix inclusion of Smnpm in the guest ISA bitmap
RISC-V: KVM: Delegate illegal instruction fault to VS mode
RISC-V: KVM: Pass VMID as parameter to kvm_riscv_hfence_xyz() APIs
RISC-V: KVM: Factor-out g-stage page table management
RISC-V: KVM: Add vmid field to struct kvm_riscv_hfence
RISC-V: KVM: Introduce struct kvm_gstage_mapping
RISC-V: KVM: Factor-out MMU related declarations into separate headers
RISC-V: KVM: Use ncsr_xyz() in kvm_riscv_vcpu_trap_redirect()
RISC-V: KVM: Implement kvm_arch_flush_remote_tlbs_range()
RISC-V: KVM: Don't flush TLB when PTE is unchanged
RISC-V: KVM: Replace KVM_REQ_HFENCE_GVMA_VMID_ALL with KVM_REQ_TLB_FLUSH
RISC-V: KVM: Rename and move kvm_riscv_local_tlb_sanitize()
RISC-V: KVM: Drop the return value of kvm_riscv_vcpu_aia_init()
RISC-V: KVM: Check kvm_riscv_vcpu_alloc_vector_context() return value
KVM: arm64: selftests: Add FEAT_RAS EL2 registers to get-reg-list
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core & protocols:
- Wrap datapath globals into net_aligned_data, to avoid false sharing
- Preserve MSG_ZEROCOPY in forwarding (e.g. out of a container)
- Add SO_INQ and SCM_INQ support to AF_UNIX
- Add SIOCINQ support to AF_VSOCK
- Add TCP_MAXSEG sockopt to MPTCP
- Add IPv6 force_forwarding sysctl to enable forwarding per interface
- Make TCP validation of whether packet fully fits in the receive
window and the rcv_buf more strict. With increased use of HW
aggregation a single "packet" can be multiple 100s of kB
- Add MSG_MORE flag to optimize large TCP transmissions via sockmap,
improves latency up to 33% for sockmap users
- Convert TCP send queue handling from tasklet to BH workque
- Improve BPF iteration over TCP sockets to see each socket exactly
once
- Remove obsolete and unused TCP RFC3517/RFC6675 loss recovery code
- Support enabling kernel threads for NAPI processing on per-NAPI
instance basis rather than a whole device. Fully stop the kernel
NAPI thread when threaded NAPI gets disabled. Previously thread
would stick around until ifdown due to tricky synchronization
- Allow multicast routing to take effect on locally-generated packets
- Add output interface argument for End.X in segment routing
- MCTP: add support for gateway routing, improve bind() handling
- Don't require rtnl_lock when fetching an IPv6 neighbor over Netlink
- Add a new neighbor flag ("extern_valid"), which cedes refresh
responsibilities to userspace. This is needed for EVPN multi-homing
where a neighbor entry for a multi-homed host needs to be synced
across all the VTEPs among which the host is multi-homed
- Support NUD_PERMANENT for proxy neighbor entries
- Add a new queuing discipline for IETF RFC9332 DualQ Coupled AQM
- Add sequence numbers to netconsole messages. Unregister
netconsole's console when all net targets are removed. Code
refactoring. Add a number of selftests
- Align IPSec inbound SA lookup to RFC 4301. Only SPI and protocol
should be used for an inbound SA lookup
- Support inspecting ref_tracker state via DebugFS
- Don't force bonding advertisement frames tx to ~333 ms boundaries.
Add broadcast_neighbor option to send ARP/ND on all bonded links
- Allow providing upcall pid for the 'execute' command in openvswitch
- Remove DCCP support from Netfilter's conntrack
- Disallow multiple packet duplications in the queuing layer
- Prevent use of deprecated iptables code on PREEMPT_RT
Driver API:
- Support RSS and hashing configuration over ethtool Netlink
- Add dedicated ethtool callbacks for getting and setting hashing
fields
- Add support for power budget evaluation strategy in PSE /
Power-over-Ethernet. Generate Netlink events for overcurrent etc
- Support DPLL phase offset monitoring across all device inputs.
Support providing clock reference and SYNC over separate DPLL
inputs
- Support traffic classes in devlink rate API for bandwidth
management
- Remove rtnl_lock dependency from UDP tunnel port configuration
Device drivers:
- Add a new Broadcom driver for 800G Ethernet (bnge)
- Add a standalone driver for Microchip ZL3073x DPLL
- Remove IBM's NETIUCV device driver
- Ethernet high-speed NICs:
- Broadcom (bnxt):
- support zero-copy Tx of DMABUF memory
- take page size into account for page pool recycling rings
- Intel (100G, ice, idpf):
- idpf: XDP and AF_XDP support preparations
- idpf: add flow steering
- add link_down_events statistic
- clean up the TSPLL code
- preparations for live VM migration
- nVidia/Mellanox:
- support zero-copy Rx/Tx interfaces (DMABUF and io_uring)
- optimize context memory usage for matchers
- expose serial numbers in devlink info
- support PCIe congestion metrics
- Meta (fbnic):
- add 25G, 50G, and 100G link modes to phylink
- support dumping FW logs
- Marvell/Cavium:
- support for CN20K generation of the Octeon chips
- Amazon:
- add HW clock (without timestamping, just hypervisor time access)
- Ethernet virtual:
- VirtIO net:
- support segmentation of UDP-tunnel-encapsulated packets
- Google (gve):
- support packet timestamping and clock synchronization
- Microsoft vNIC:
- add handler for device-originated servicing events
- allow dynamic MSI-X vector allocation
- support Tx bandwidth clamping
- Ethernet NICs consumer, and embedded:
- AMD:
- amd-xgbe: hardware timestamping and PTP clock support
- Broadcom integrated MACs (bcmgenet, bcmasp):
- use napi_complete_done() return value to support NAPI polling
- add support for re-starting auto-negotiation
- Broadcom switches (b53):
- support BCM5325 switches
- add bcm63xx EPHY power control
- Synopsys (stmmac):
- lots of code refactoring and cleanups
- TI:
- icssg-prueth: read firmware-names from device tree
- icssg: PRP offload support
- Microchip:
- lan78xx: convert to PHYLINK for improved PHY and MAC management
- ksz: add KSZ8463 switch support
- Intel:
- support similar queue priority scheme in multi-queue and
time-sensitive networking (taprio)
- support packet pre-emption in both
- RealTek (r8169):
- enable EEE at 5Gbps on RTL8126
- Airoha:
- add PPPoE offload support
- MDIO bus controller for Airoha AN7583
- Ethernet PHYs:
- support for the IPQ5018 internal GE PHY
- micrel KSZ9477 switch-integrated PHYs:
- add MDI/MDI-X control support
- add RX error counters
- add cable test support
- add Signal Quality Indicator (SQI) reporting
- dp83tg720: improve reset handling and reduce link recovery time
- support bcm54811 (and its MII-Lite interface type)
- air_en8811h: support resume/suspend
- support PHY counters for QCA807x and QCA808x
- support WoL for QCA807x
- CAN drivers:
- rcar_canfd: support for Transceiver Delay Compensation
- kvaser: report FW versions via devlink dev info
- WiFi:
- extended regulatory info support (6 GHz)
- add statistics and beacon monitor for Multi-Link Operation (MLO)
- support S1G aggregation, improve S1G support
- add Radio Measurement action fields
- support per-radio RTS threshold
- some work around how FIPS affects wifi, which was wrong (RC4 is
used by TKIP, not only WEP)
- improvements for unsolicited probe response handling
- WiFi drivers:
- RealTek (rtw88):
- IBSS mode for SDIO devices
- RealTek (rtw89):
- BT coexistence for MLO/WiFi7
- concurrent station + P2P support
- support for USB devices RTL8851BU/RTL8852BU
- Intel (iwlwifi):
- use embedded PNVM in (to be released) FW images to fix
compatibility issues
- many cleanups (unused FW APIs, PCIe code, WoWLAN)
- some FIPS interoperability
- MediaTek (mt76):
- firmware recovery improvements
- more MLO work
- Qualcomm/Atheros (ath12k):
- fix scan on multi-radio devices
- more EHT/Wi-Fi 7 features
- encapsulation/decapsulation offload
- Broadcom (brcm80211):
- support SDIO 43751 device
- Bluetooth:
- hci_event: add support for handling LE BIG Sync Lost event
- ISO: add socket option to report packet seqnum via CMSG
- ISO: support SCM_TIMESTAMPING for ISO TS
- Bluetooth drivers:
- intel_pcie: support Function Level Reset
- nxpuart: add support for 4M baudrate
- nxpuart: implement powerup sequence, reset, FW dump, and FW loading"
* tag 'net-next-6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1742 commits)
dpll: zl3073x: Fix build failure
selftests: bpf: fix legacy netfilter options
ipv6: annotate data-races around rt->fib6_nsiblings
ipv6: fix possible infinite loop in fib6_info_uses_dev()
ipv6: prevent infinite loop in rt6_nlmsg_size()
ipv6: add a retry logic in net6_rt_notify()
vrf: Drop existing dst reference in vrf_ip6_input_dst
net/sched: taprio: align entry index attr validation with mqprio
net: fsl_pq_mdio: use dev_err_probe
selftests: rtnetlink.sh: remove esp4_offload after test
vsock: remove unnecessary null check in vsock_getname()
igb: xsk: solve negative overflow of nb_pkts in zerocopy mode
stmmac: xsk: fix negative overflow of budget in zerocopy mode
dt-bindings: ieee802154: Convert at86rf230.txt yaml format
net: dsa: microchip: Disable PTP function of KSZ8463
net: dsa: microchip: Setup fiber ports for KSZ8463
net: dsa: microchip: Write switch MAC address differently for KSZ8463
net: dsa: microchip: Use different registers for KSZ8463
net: dsa: microchip: Add KSZ8463 switch support to KSZ DSA driver
dt-bindings: net: dsa: microchip: Add KSZ8463 switch support
...
|
|
IRQchip drivers need a PCI/MSI function to map a RID to a MSI
controller deviceID namespace and at the same time retrieve the
struct device_node pointer of the MSI controller the RID is mapped
to.
Add pci_msi_map_rid_ctlr_node() to achieve this purpose.
Cc Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20250703-gicv5-host-v7-25-12e71f1b3528@kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
|
|
Add device pointer to irq_domain_info and msi_domain_info, so that the device
can be specified at domain creation time.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/943e52403b20cf13c320d55bd4446b4562466aab.1750860131.git.namcao@linutronix.de
|
|
For supporting dynamic MSI-X vector allocation by PCI controllers, enabling
the flag MSI_FLAG_PCI_MSIX_ALLOC_DYN is not enough, msix_prepare_msi_desc()
to prepare the MSI descriptor is also needed.
Export pci_msix_prepare_desc() to allow PCI controllers to support dynamic
MSI-X vector allocation.
Signed-off-by: Shradha Gupta <shradhagupta@linux.microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Saurabh Sengar <ssengar@linux.microsoft.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Creating an irq domain that serves as an MSI parent requires
a substantial amount of esoteric boiler-plate code, some of
which is often provided twice (such as the bus token).
To make things a bit simpler for the unsuspecting MSI tinkerer,
provide a helper that does it for them, and serves as documentation
of what needs to be provided.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250513172819.2216709-3-maz@kernel.org
|
|
The current device MSI infrastructure is subtly broken, as it will issue an
.msi_prepare() callback into the MSI controller driver every time it needs
to allocate an MSI. That's pretty wrong, as the contract (or unwarranted
assumption, depending who you ask) between the MSI controller and the core
code is that .msi_prepare() is called exactly once per device.
This leads to some subtle breakage in some MSI controller drivers, as it
gives the impression that there are multiple endpoints sharing a bus
identifier (RID in PCI parlance, DID for GICv3+). It implies that whatever
allocation the ITS driver (for example) has done on behalf of these devices
cannot be undone, as there is no way to track the shared state. This is
particularly bad for wire-MSI devices, for which .msi_prepare() is called
for each input line.
To address this issue, move the call to .msi_prepare() to take place at the
point of irq domain allocation, which is the only place that makes
sense. The msi_alloc_info_t structure is made part of the
msi_domain_template, so that its life-cycle is that of the domain as well.
Finally, the msi_info::alloc_data field is made to point at this allocation
tracking structure, ensuring that it is carried around the block.
This is all pretty straightforward, except for the non-device-MSI
leftovers, which still have to call .msi_prepare() at the old spot. One
day...
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250513163144.2215824-4-maz@kernel.org
|
|
While the MSI ops do have a .msi_prepare() callback that is responsible for
setting up the relevant (usually per-device) allocation, there is no
callback reversing this setup.
For this purpose, add .msi_teardown() callback.
In order to avoid breaking the ITS driver that suffers from related issues,
do not call the callback just yet.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250513163144.2215824-2-maz@kernel.org
|
|
Now that all abuse is gone and the legit users are converted to
guard(msi_descs_lock), rename the lock functions and document them as
internal.
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huwei.com>
Link: https://lore.kernel.org/all/20250319105506.864699741@linutronix.de
|
|
Provide a lock guard for MSI descriptor locking and update the core code
accordingly.
No functional change intended.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/all/20250319105506.144672678@linutronix.de
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip"
This reverts commit 36f5f026df6c1cd8a20373adc4388d2b3401ce91, reversing
changes made to 43a7eec035a5b64546c8adefdc9cf96a116da14b.
Thomas says:
"I just noticed that for some incomprehensible reason, probably sheer
incompetemce when trying to utilize b4, I managed to merge an outdated
_and_ buggy version of that series.
Can you please revert that merge completely?"
Done.
Requested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/iommu/linux
Pull iommu updates from Joerg Roedel:
"Core iommufd dependencies from Jason:
- Change the iommufd fault handle into an always present hwpt handle
in the domain
- Give iommufd its own SW_MSI implementation along with some IRQ
layer rework
- Improvements to the handle attach API
Core fixes for probe-issues from Robin
Intel VT-d changes:
- Checking for SVA support in domain allocation and attach paths
- Move PCI ATS and PRI configuration into probe paths
- Fix a pentential hang on reboot -f
- Miscellaneous cleanups
AMD-Vi changes:
- Support for up to 2k IRQs per PCI device function
- Set of smaller fixes
ARM-SMMU changes:
- SMMUv2 devicetree binding updates for Qualcomm implementations
(QCS8300 GPU and MSM8937)
- Clean up SMMUv2 runtime PM implementation to help with wider rework
of pm_runtime_put_autosuspend()
Rockchip driver changes:
- Driver adjustments for recent DT probing changes
S390 IOMMU changes:
- Support for IOMMU passthrough
Apple Dart changes:
- Driver adjustments to meet ISP device requirements
- Null-ptr deref fix
- Disable subpage protection for DART 1"
* tag 'iommu-updates-v6.15' of git://git.kernel.org/pub/scm/linux/kernel/git/iommu/linux: (54 commits)
iommu/vt-d: Fix possible circular locking dependency
iommu/vt-d: Don't clobber posted vCPU IRTE when host IRQ affinity changes
iommu/vt-d: Put IRTE back into posted MSI mode if vCPU posting is disabled
iommu: apple-dart: fix potential null pointer deref
iommu/rockchip: Retire global dma_dev workaround
iommu/rockchip: Register in a sensible order
iommu/rockchip: Allocate per-device data sensibly
iommu/mediatek-v1: Support COMPILE_TEST
iommu/amd: Enable support for up to 2K interrupts per function
iommu/amd: Rename DTE_INTTABLEN* and MAX_IRQS_PER_TABLE macro
iommu/amd: Replace slab cache allocator with page allocator
iommu/amd: Introduce generic function to set multibit feature value
iommu: Don't warn prematurely about dodgy probes
iommu/arm-smmu: Set rpm auto_suspend once during probe
dt-bindings: arm-smmu: Document QCS8300 GPU SMMU
iommu: Get DT/ACPI parsing into the proper probe path
iommu: Keep dev->iommu state consistent
iommu: Resolve ops in iommu_init_device()
iommu: Handle race with default domain setup
iommu: Unexport iommu_fwspec_free()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen updates from Juergen Gross:
- cleanup: remove an used function
- add support for a XenServer specific virtual PCI device
- fix the handling of a sparse Xen hypervisor symbol table
- avoid warnings when building the kernel with gcc 15
- fix use of devices behind a VMD bridge when running as a Xen PV dom0
* tag 'for-linus-6.15-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
PCI/MSI: Convert pci_msi_ignore_mask to per MSI domain flag
PCI: vmd: Disable MSI remapping bypass under Xen
xen/pci: Do not register devices with segments >= 0x10000
xen/pciback: Remove unused pcistub_get_pci_dev
xenfs/xensyms: respect hypervisor's "next" indication
xen/mcelog: Add __nonstring annotations for unterminated strings
xen: Add support for XenServer 6.1 platform device
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq driver updates from Thomas Gleixner:
- Support for hard indices on RISC-V. The hart index identifies a hart
(core) within a specific interrupt domain in RISC-V's Priviledged
Architecture.
- Rework of the RISC-V MSI driver
This moves the driver over to the generic MSI library and solves the
affinity problem of unmaskable PCI/MSI controllers. Unmaskable
PCI/MSI controllers are prone to lose interrupts when the MSI message
is updated to change the affinity because the message write consists
of three 32-bit subsequent writes, which update address and data. As
these writes are non-atomic versus the device raising an interrupt,
the device can observe a half written update and issue an interrupt
on the wrong vector. This is mitiated by a carefully orchestrated
step by step update and the observation of an eventually pending
interrupt on the CPU which issues the update. The algorithm follows
the well established method of the X86 MSI driver.
- A new driver for the RISC-V Sophgo SG2042 MSI controller
- Overhaul of the Renesas RZQ2L driver
Simplification of the probe function by using devm_*() mechanisms,
which avoid the endless list of error prone gotos in the failure
paths.
- Expand the Renesas RZV2H driver to support RZ/G3E SoCs
- A workaround for Rockchip 3568002 erratum in the GIC-V3 driver to
ensure that the addressing is limited to the lower 32-bit of the
physical address space.
- Add support for the Allwinner AS23 NMI controller
- Expand the IMX irqsteer driver to handle up to 960 input interrupts
- The usual small updates, cleanups and device tree changes
* tag 'irq-drivers-2025-03-23' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (40 commits)
irqchip/imx-irqsteer: Support up to 960 input interrupts
irqchip/sunxi-nmi: Support Allwinner A523 NMI controller
dt-bindings: irq: sun7i-nmi: Document the Allwinner A523 NMI controller
irqchip/davinci-cp-intc: Remove public header
irqchip/renesas-rzv2h: Add RZ/G3E support
irqchip/renesas-rzv2h: Update macros ICU_TSSR_TSSEL_{MASK,PREP}
irqchip/renesas-rzv2h: Update TSSR_TIEN macro
irqchip/renesas-rzv2h: Add field_width to struct rzv2h_hw_info
irqchip/renesas-rzv2h: Add max_tssel to struct rzv2h_hw_info
irqchip/renesas-rzv2h: Add struct rzv2h_hw_info with t_offs variable
irqchip/renesas-rzv2h: Use devm_pm_runtime_enable()
irqchip/renesas-rzv2h: Use devm_reset_control_get_exclusive_deasserted()
irqchip/renesas-rzv2h: Simplify rzv2h_icu_init()
irqchip/renesas-rzv2h: Drop irqchip from struct rzv2h_icu_priv
irqchip/renesas-rzv2h: Fix wrong variable usage in rzv2h_tint_set_type()
dt-bindings: interrupt-controller: renesas,rzv2h-icu: Document RZ/G3E SoC
riscv: sophgo: dts: Add msi controller for SG2042
irqchip: Add the Sophgo SG2042 MSI interrupt controller
dt-bindings: interrupt-controller: Add Sophgo SG2042 MSI
arm64: dts: rockchip: rk356x: Move PCIe MSI to use GIC ITS instead of MBI
...
|
|
Setting pci_msi_ignore_mask inhibits the toggling of the mask bit for both
MSI and MSI-X entries globally, regardless of the IRQ chip they are using.
Only Xen sets the pci_msi_ignore_mask when routing physical interrupts over
event channels, to prevent PCI code from attempting to toggle the maskbit,
as it's Xen that controls the bit.
However, the pci_msi_ignore_mask being global will affect devices that use
MSI interrupts but are not routing those interrupts over event channels
(not using the Xen pIRQ chip). One example is devices behind a VMD PCI
bridge. In that scenario the VMD bridge configures MSI(-X) using the
normal IRQ chip (the pIRQ one in the Xen case), and devices behind the
bridge configure the MSI entries using indexes into the VMD bridge MSI
table. The VMD bridge then demultiplexes such interrupts and delivers to
the destination device(s). Having pci_msi_ignore_mask set in that scenario
prevents (un)masking of MSI entries for devices behind the VMD bridge.
Move the signaling of no entry masking into the MSI domain flags, as that
allows setting it on a per-domain basis. Set it for the Xen MSI domain
that uses the pIRQ chip, while leaving it unset for the rest of the
cases.
Remove pci_msi_ignore_mask at once, since it was only used by Xen code, and
with Xen dropping usage the variable is unneeded.
This fixes using devices behind a VMD bridge on Xen PV hardware domains.
Albeit Devices behind a VMD bridge are not known to Xen, that doesn't mean
Linux cannot use them. By inhibiting the usage of
VMD_FEAT_CAN_BYPASS_MSI_REMAP and the removal of the pci_msi_ignore_mask
bodge devices behind a VMD bridge do work fine when use from a Linux Xen
hardware domain. That's the whole point of the series.
Signed-off-by: Roger Pau Monné <roger.pau@citrix.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Juergen Gross <jgross@suse.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Message-ID: <20250219092059.90850-4-roger.pau@citrix.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
Now that all abuse is gone and the legit users are converted to
guard(msi_descs_lock), rename the lock functions and document them as
internal.
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huwei.com>
Link: https://lore.kernel.org/all/20250313130322.027190131@linutronix.de
|
|
Provide a lock guard for MSI descriptor locking and update the core code
accordingly.
No functional change intended.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/all/20250313130321.506045185@linutronix.de
|
|
None of these functions are used outside of the MSI core.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250309084110.204054172@linutronix.de
|
|
The two-step process to translate the MSI address involves two functions,
iommu_dma_prepare_msi() and iommu_dma_compose_msi_msg().
Previously iommu_dma_compose_msi_msg() needed to be in the iommu layer as
it had to dereference the opaque cookie pointer. Now, the previous patch
changed the cookie pointer into an integer so there is no longer any need
for the iommu layer to be involved.
Further, the call sites of iommu_dma_compose_msi_msg() all follow the same
pattern of setting an MSI message address_hi/lo to non-translated and then
immediately calling iommu_dma_compose_msi_msg().
Refactor iommu_dma_compose_msi_msg() into msi_msg_set_addr() that directly
accepts the u64 version of the address and simplifies all the callers.
Move the new helper to linux/msi.h since it has nothing to do with iommu.
Aside from refactoring, this logically prepares for the next patch, which
allows multiple implementation options for iommu_dma_prepare_msi(). So, it
does not make sense to have the iommu_dma_compose_msi_msg() in dma-iommu.c
as it no longer provides the only iommu_dma_prepare_msi() implementation.
Link: https://patch.msgid.link/r/eda62a9bafa825e9cdabd7ddc61ad5a21c32af24.1740014950.git.nicolinc@nvidia.com
Signed-off-by: Nicolin Chen <nicolinc@nvidia.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
|
|
The IOMMU translation for MSI message addresses has been a 2-step process,
separated in time:
1) iommu_dma_prepare_msi(): A cookie pointer containing the IOVA address
is stored in the MSI descriptor when an MSI interrupt is allocated.
2) iommu_dma_compose_msi_msg(): this cookie pointer is used to compute a
translated message address.
This has an inherent lifetime problem for the pointer stored in the cookie
that must remain valid between the two steps. However, there is no locking
at the irq layer that helps protect the lifetime. Today, this works under
the assumption that the iommu domain is not changed while MSI interrupts
being programmed. This is true for normal DMA API users within the kernel,
as the iommu domain is attached before the driver is probed and cannot be
changed while a driver is attached.
Classic VFIO type1 also prevented changing the iommu domain while VFIO was
running as it does not support changing the "container" after starting up.
However, iommufd has improved this so that the iommu domain can be changed
during VFIO operation. This potentially allows userspace to directly race
VFIO_DEVICE_ATTACH_IOMMUFD_PT (which calls iommu_attach_group()) and
VFIO_DEVICE_SET_IRQS (which calls into iommu_dma_compose_msi_msg()).
This potentially causes both the cookie pointer and the unlocked call to
iommu_get_domain_for_dev() on the MSI translation path to become UAFs.
Fix the MSI cookie UAF by removing the cookie pointer. The translated IOVA
address is already known during iommu_dma_prepare_msi() and cannot change.
Thus, it can simply be stored as an integer in the MSI descriptor.
The other UAF related to iommu_get_domain_for_dev() will be addressed in
patch "iommu: Make iommu_dma_prepare_msi() into a generic operation" by
using the IOMMU group mutex.
Link: https://patch.msgid.link/r/a4f2cd76b9dc1833ee6c1cf325cba57def22231c.1740014950.git.nicolinc@nvidia.com
Signed-off-by: Nicolin Chen <nicolinc@nvidia.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
|
|
msi_lib_init_dev_msi_info() sets the default irq_eoi()/irq_ack() callbacks
unconditionally. This is correct for all existing users, but prevents the
IMSIC driver to be moved to the MSI library implementation.
Introduce chip_flags in struct msi_parent_ops, which instruct the library
to selectively set the callbacks depending on the flags, and update all
current users to set them.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250217085657.789309-3-apatel@ventanamicro.com
|
|
Various PCI controllers that mux MSIs onto a single IRQ line produce these
"IRQ%d: set affinity failed" warnings when entering suspend. This has been
discussed before [1] [2] and an example test case is included at the end of
this commit message.
Controller drivers that create MSI IRQ domain with
MSI_FLAG_USE_DEF_CHIP_OPS and do not override the .irq_set_affinity()
irqchip callback get assigned the default msi_domain_set_affinity()
callback. That is not desired on controllers w |
