| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
It's strongly recommended for GPIO drivers to always implement the
.get_direction() callback - even when the direction is tracked in
software. The GPIO core emits a warning when the callback is missing
and a user reads the direction of a line, e.g. via
/sys/kernel/debug/gpio.
Fixes: dfeae619d781 ("serial: sc16is7xx")
Cc: stable <stable@kernel.org>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Link: https://patch.msgid.link/20260716210813.2582826-1-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
platforms
Commit b1b4efea05a5 ("serial: 8250_mid: Disable DMA for selected
platforms") replaced the dnv_board setup and exit callbacks with
PTR_IF(false, ...), which evaluates to NULL. However, the three call
sites in mid8250_probe() and mid8250_remove() unconditionally
dereference these function pointers without NULL checks, causing a NULL
pointer dereference (kernel oops) on any Denverton (DNV), Ice Lake Xeon
D (ICX-D/CDF), or Snowridge (SNR) platform.
Fix this by adding the missing NULL checks before calling the setup and
exit callbacks.
Fixes: b1b4efea05a5 ("serial: 8250_mid: Disable DMA for selected platforms")
Cc: stable <stable@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jiangshan Yi <yijiangshan@kylinos.cn>
Link: https://patch.msgid.link/20260715073546.1875083-1-yijiangshan@kylinos.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some small tty/serial/vt fixes for 7.2-rc3 that resolve some
reported problems. Included in here are:
- vt spurious modifier issue that showed up in -rc1 (reported a
bunch)
- 8250 driver bugfixes
- msm serial driver bugfix
- max310x serial driver bugfix
All of these have been in linux-next with no reported issues"
* tag 'tty-7.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: 8250: Ignore flow control on suspend/resume with no_console_suspend
serial: 8250_mid: Disable DMA for selected platforms
serial: 8250_omap: clear rx_running on zero-length DMA completes
vt: fix spurious modifier in CSI/cursor key sequences
serial: msm: Disable DMA for kernel console UART
serial: max310x: implement gpio_chip::get_direction()
|
|
If no_console_suspend is specified, on suspend the 8250 console driver
uses a scratch register (UART_SCR) to store a special canary value. This
is used during the resume path to identify a printk() call before the
driver's own ->resume() callback. In this case,
serial8250_console_restore() is called to quickly re-init the 8250 for
console printing.
See commit 4516d50aabed ("serial: 8250: Use canary to restart console after
suspend") for the original motivation.
Unfortunately, this canary workaround does not work in all cases (such as
suspend to mem) because the scratch register will not reset. This has not
been a real issue until now because it could simply lead to some garbage
characters upon resume. However, with the introduction of console flow
control it becomes a real problem because a failed suspend/resume detection
when flow control is enabled leads to all characters hitting the flow
control timeout.
Workaround this issue by temporarily ignoring console flow control when
the debug canary suspend/resume detection is active.
Fixes: 5e6dfb87b191 ("serial: 8250: Add support for console flow control")
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://patch.msgid.link/20260707141032.5074-1-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In accordance with Errata (specification updates)
HSUART May Stop Functioning when DMA is Active.
- Denverton document #572409, rev 3.4, DNV60
- Ice Lake Xeon D document #714070, ICXD65
- Snowridge document #731931, SNR44
For a quick fix just disable the respective callbacks during the device probe.
Depending on the future development we might remove them completely.
Reported-by: micas-opensource <zjianan156@gmail.com>
Closes: https://lore.kernel.org/linux-serial/20250625031409.2404219-1-opensource@ruijie.com.cn/
Fixes: 6ede6dcd87aa ("serial: 8250_mid: add support for DMA engine handling from UART MMIO")
Cc: stable <stable@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20260626094937.561776-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
On AM33xx RX DMA only triggers when the FIFO reaches the
configured threshold (typically 48 bytes). For smaller bursts
no DMA request is issued and the FIFO is drained by RX timeout.
In this case __dma_rx_do_complete() can legitimately see count == 0.
The current code exits early in this case and does not clear
dma->rx_running, leaving the DMA state inconsistent. This can
prevent RX DMA from restarting and may cause
omap_8250_rx_dma_flush() to fail, marking DMA as broken.
Fix this by clearing dma->rx_running once the DMA transfer has
completed or been terminated, even if no data was transferred.
Fixes: a5fd8945a478 ("serial: 8250: 8250_omap.c: Clear DMA RX running status only after DMA termination is done")
Cc: stable <stable@kernel.org>
Signed-off-by: Matthias Feser <mfe@KBSgmbhfr.onmicrosoft.com>
Reviewed-by: Moteen Shah <m-shah@ti.com>
Link: https://patch.msgid.link/BE3P281MB55155F2F5795E411F5A65282EE0B2@BE3P281MB5515.DEUP281.PROD.OUTLOOK.COM
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
At the moment, concurrent writes from userspace and the kernel to the
console can trigger a race condition that results in an infinite loop of
the same messages printed over and over again. This is most likely to
happen during system startup or shutdown when the init system starts/stops
a large number of system services that interact with various kernel code.
When userspace writes to the TTY device, the driver initiates an
asynchronous DMA transfer and releases the port lock. At the same moment,
the kernel printk path might grab the port lock and re-configure the UART
controller for PIO, without waiting for the DMA operation to complete. It
seems like this collision results in zero progress being reported for the
DMA engine, so the same text is printed to the console over and over again.
For the kernel console, we want a reliable output path that will be
functional even during crashes etc. So rather than implementing complex
code to synchronize the kernel console write routines with the userspace
DMA write routines, simply disable DMA for the console UART instance.
Similar checks exist in many other serial drivers, e.g. 8250_port.c,
imx.c, sh-sci.c etc.
Cc: stable <stable@kernel.org>
Fixes: 3a878c430fd6 ("tty: serial: msm: Add TX DMA support")
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Acked-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://patch.msgid.link/20260706-serial-msm-console-dma-collision-v1-1-3179b8cb1d89@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It's strongly recommended for GPIO drivers to always implement the
.get_direction() callback - even when the direction is tracked in
software. The GPIO core emits a warning when the callback is missing
and a user reads the direction of a line, e.g. via
/sys/kernel/debug/gpio.
The MAX310X keeps the GPIO direction in the GPIOCFG register (a set bit
selects output), which the existing direction_input/output callbacks
already program, so the current direction can be read back directly.
Fixes: f65444187a66 ("serial: New serial driver MAX310X")
Cc: stable <stable@kernel.org>
Signed-off-by: Tapio Reijonen <tapio.reijonen@vaisala.com>
Reviewed-by: Linus Walleij <linusw@kernel.org>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Reviewed-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://patch.msgid.link/20260615-b4-serial-max310x-gpio-get-direction-v2-1-4704ba2b181a@vaisala.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
files)
Replace the #include of <linux/mod_devicetable.h> by the more specific
<linux/device-id/*.h> where applicable. For most cases the include
can be dropped completely, only a few drivers need one or two headers
added.
Acked-by: Danilo Krummrich <dakr@kernel.org>
Acked-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/1a3f2007c5c5dcf555c09a4035ce3ae8ef1b6c49.1782808461.git.u.kleine-koenig@baylibre.com
Signed-off-by: Uwe Kleine-König (The Capable Hub) <u.kleine-koenig@baylibre.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial driver updates from Greg KH:
"Here is the big set of TTY and Serial driver updates for 7.2-rc1.
Overall we end up removing more code than added, due to an obsolete
synclink_gt driver being removed from the tree, always a nice thing to
see happen.
Other than that driver removal, major things included in here are:
- max310x serial driver updates and fixes
- 8250 driver updates and rework in places to make it more "modern"
- dts file updates
- serial driver core tweaks and updates
- vt code cleanups
- vc_screen crash fixes
- other minor driver updates and cleanups
All of these have been in linux-next for well over a week with no
reported issues"
* tag 'tty-7.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (49 commits)
serial: 8250_pci: Don't specify conflicting values to pci_device_id members
vc_screen: fix null-ptr-deref in vcs_notifier() during concurrent vcs_write
serial: qcom_geni: Fix RX DMA stall when SE_DMA_RX_LEN_IN is zero
vt: merge ucs_is_zero_width()/ucs_is_double_width() into ucs_get_width()
serial: 8250: fix possible ISR soft lockup
dt-bindings: serial: rs485: remove deprecated .txt binding stub
serial: qcom-geni: trace: Add tracepoint support for Qualcomm GENI serial
tty: serial: Use named initializers for arrays of i2c_device_data
serial: 8250_dw: remove clock-notifier infrastructure
serial: 8250_dw: unregister 8250 port if clk_notifier_register() fails
amba/serial: amba-pl011: Bring back zx29 UART support
serial: 8250: Add support for console flow control
serial: 8250: Check LSR timeout on console flow control
serial: 8250: Set cons_flow on port registration
tty: serial: 8250: protect against NULL uart->port.dev in register
arm64: dts: add support for A9 based Amlogic BY401
dt-bindings: arm: amlogic: add A311Y3 support
serial: max310x: fix compile errors if CONFIG_SPI_MASTER is disabled
serial: qcom-geni: Avoid probing debug console UART without console support
serial: max310x: add comments for PLL limits
...
|
|
gitolite.kernel.org:pub/scm/linux/kernel/git/driver-core/driver-core
Pull driver core updates from Danilo Krummrich:
"Deferred probe:
- Fix race where deferred probe timeout work could be permanently
canceled by using mod_delayed_work()
- Fix missing jiffies conversion in deferred_probe_extend_timeout()
- Guard timeout extension with delayed_work_pending() to prevent
premature firing
- Use system_percpu_wq instead of the deprecated system_wq
- Update deferred_probe_timeout documentation
device:
- Replace direct struct device bitfield access (can_match, dma_iommu,
dma_skip_sync, dma_ops_bypass, state_synced, dma_coherent,
of_node_reused, offline, offline_disabled) with flag-based
accessors using bit operations
- Reject devices with unregistered buses
- Delete unused DEVICE_ATTR_PREALLOC()
- Add low-level device attribute macros with const show/store
callbacks, allowing device attributes to reside in read-only memory
- Move core device attributes to read-only memory
- Constify group array pointers in driver_add_groups() /
driver_remove_groups(), struct bus_type, and struct device_driver
device property:
- Fix fwnode reference leak in fwnode_graph_get_endpoint_by_id()
- Initialize all fields of fwnode_handle in fwnode_init()
- Provide swnode_get()/swnode_put() wrappers around kobject_get/put()
- Allow passing struct software_node_ref_args pointers directly to
PROPERTY_ENTRY_REF()
driver_override:
- Migrate amba, cdx, vmbus, and rpmsg to the generic driver_override
infrastructure, fixing a UAF from unsynchronized access to
driver_override in bus match() callbacks
- Remove the now-unused driver_set_override()
firmware loader:
- Fix recursive lock deadlock in device_cache_fw_images() when async
work falls back to synchronous execution
- Fix device reference leak in firmware_upload_register()
platform:
- Pass KBUILD_MODNAME through the platform driver registration macro
to create module symlinks in sysfs for built-in drivers; move
module_kset initialization to a pure_initcall and tegra cbb
registration to core_initcall to ensure correct ordering
- Pass THIS_MODULE implicitly through a coresight_init_driver() macro
sysfs:
- Upgrade OOB write detection in sysfs_kf_seq_show() from printk to
WARN
- Add return value clamping to sysfs_kf_read()
Rust:
- ACPI:
Fix missing match data for PRP0001 by exporting
acpi_of_match_device()
- Auxiliary:
Replace drvdata() with dedicated registration data on
auxiliary_device. drvdata() exposed the driver's bus device private
data beyond the driver's own scope, creating ordering constraints
and forcing the data to outlive all registrations that access it.
Registration data is instead scoped structurally to the
Registration object, making lifecycle ordering enforced by
construction rather than convention.
- Rust-native device driver lifetimes (HRT):
Allow Rust device drivers to carry a lifetime parameter on their
bus device private data, tied to the device binding scope -- the
interval during which a bus device is bound to a driver. Device
resources like pci::Bar<'a> and IoMem<'a> can be stored directly in
the driver's bus device private data with a lifetime bounded by the
binding scope, so the compiler enforces at build time that they do
not outlive the binding. This removes Devres indirection from every
access site and eliminates try_access() failure paths in
destructors.
Bus driver traits use a Generic Associated Type (GAT) Data<'bound>
to introduce the lifetime on the private data, rather than
parameterizing the Driver trait itself. Auxiliary registration
data, where the lifetime is not introduced by a trait callback but
must be threaded through Registration, uses the ForLt trait (a
type-level abstraction for types generic over a lifetime).
Misc:
- Fix DT overlayed devices not probing by reverting the broken
treewide overlay fix and re-running fw_devlink consumer pickup when
an overlay is applied to a bound device
- Use root_device_register() for faux bus root device; add sanity
check for failed bus init
- Fix dev_has_sync_state() data race with READ_ONCE() and move it to
base.h
- Avoid spurious device_links warning when removing a device while
its supplier is unbinding
- Switch ISA bus to dynamic root device
- Fix suspicious RCU usage in kernfs_put()
- Remove devcoredump exit callback
- Constify devfreq_event_class"
* tag 'driver-core-7.2-rc1' of gitolite.kernel.org:pub/scm/linux/kernel/git/driver-core/driver-core: (81 commits)
software node: allow passing reference args to PROPERTY_ENTRY_REF()
driver core: platform: set mod_name in driver registration
coresight: pass THIS_MODULE implicitly through a macro
kernel: param: initialize module_kset in a pure_initcall
soc/tegra: cbb: Move driver registration from pure_initcall to core_initcall
firmware_loader: Fix recursive lock in device_cache_fw_images()
driver core: Use system_percpu_wq instead of system_wq
driver core: remove driver_set_override()
rpmsg: use generic driver_override infrastructure
Drivers: hv: vmbus: use generic driver_override infrastructure
cdx: use generic driver_override infrastructure
amba: use generic driver_override infrastructure
rust: devres: add 'static bound to Devres<T>
samples: rust: rust_driver_auxiliary: showcase lifetime-bound registration data
rust: auxiliary: generalize Registration over ForLt
rust: types: add `ForLt` trait for higher-ranked lifetime support
gpu: nova-core: separate driver type from driver data
samples: rust: rust_driver_pci: use HRT lifetime for Bar
rust: io: make IoMem and ExclusiveIoMem lifetime-parameterized
rust: pci: make Bar lifetime-parameterized
...
|
|
The PCI_VDEVICE macro assigns 0 to .class and .class_mask to allow the
next value in the initializer to define the value for .driver_data.
So the construct
{
PCI_VDEVICE(INTASHIELD, 0x0D21),
.class = PCI_CLASS_COMMUNICATION_MULTISERIAL << 8,
.class_mask = 0xffff00,
.driver_data = pbn_b2_4_115200,
},
introduced in commit 44e55f1f3088 ("serial: 8250_pci: Consistently
define pci_device_ids using named initializers") has conflicting
assignments. In only some configurations (i.e. W=1 for me) that makes
the compiler unhappy.
So convert the two affected items to PCI_DEVICE which doesn't have that
hidden assigment to .class and .class_mask.
Fixes: 44e55f1f3088 ("serial: 8250_pci: Consistently define pci_device_ids using named initializers")
Signed-off-by: Uwe Kleine-König (The Capable Hub) <u.kleine-koenig@baylibre.com>
Reported-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Closes: https://lore.kernel.org/linux-serial/ah_5qVKOf8LXG1Xo@ashevche-desk.local/T/#ma6eab90ca801b4292639f5c255a89b4033b33d21
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20260603095616.937968-2-u.kleine-koenig@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In qcom_geni_serial_handle_rx_dma(), geni_se_rx_dma_unprep() clears
port->rx_dma_addr before SE_DMA_RX_LEN_IN is read. If the register is zero,
for example when the RX stale counter fires on an idle line, the handler
returns without calling geni_se_rx_dma_prep().
The next RX DMA interrupt then hits the !port->rx_dma_addr guard and
returns immediately, so the RX DMA buffer is never rearmed and later input
is lost.
Keep the handler on the rearm path when rx_in is zero. Warn about the
unexpected zero-length DMA completion, skip received-data handling, and
always call geni_se_rx_dma_prep().
Fixes: 2aaa43c70778 ("tty: serial: qcom-geni-serial: add support for serial engine DMA")
Cc: stable@vger.kernel.org
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Viken Dadhaniya <viken.dadhaniya@oss.qualcomm.com>
Link: https://patch.msgid.link/20260528-serial-rx-0-byte-fix-v2-1-b4195cfe342f@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the tty/serial fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Enable modular build since the driver now has a proper module_exit()
handler. There's nothing specific to DZ hardware to prevent driver
unloading and reloading from working.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://patch.msgid.link/alpine.DEB.2.21.2605062331420.46195@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Prevent a crash from happening as the first serial port is initialised:
Console: switching to mono frame buffer device 160x64
fb0: PMAG-AA frame buffer device at tc0
DECstation Z85C30 serial driver version 0.10
CPU 0 Unable to handle kernel paging request at virtual address 0000002c, epc == 803ab00c, ra == 803aafe0
Oops[#1]:
CPU: 0 PID: 1 Comm: swapper Not tainted 6.4.0-rc3-00031-g84a9582fd203-dirty #57
$ 0 : 00000000 10012c00 803aaeb0 00000000
$ 4 : 80e12f60 80e12f50 80e12f58 81000030
$ 8 : 00000000 805ff37c 00000000 33433538
$12 : 65732030 00000006 80c2915d 6c616972
$16 : 80e12f00 807b7630 00000000 00000000
$20 : 00000004 00000348 000001a0 807623b8
$24 : 00000018 00000000
$28 : 80c24000 80c25d60 8078b148 803aafe0
Hi : 00000000
Lo : 00000000
epc : 803ab00c serial_base_ctrl_add+0x78/0xf4
ra : 803aafe0 serial_base_ctrl_add+0x4c/0xf4
Status: 10012c03 KERNEL EXL IE
Cause : 00000008 (ExcCode 02)
BadVA : 0000002c
PrId : 00000440 (R4400SC)
Modules linked in:
Process swapper (pid: 1, threadinfo=(ptrval), task=(ptrval), tls=00000000)
Stack : 80760000 00000cc0 00400044 00400040 803aa02c 80d61ab8 00000000 807b7630
80760000 807623b8 807b7628 803aa644 80386998 00000000 80e17780 80220f68
80e17780 80d61ab8 80c17d80 80e17780 80e17780 8063c798 80e17780 80383fa0
00000010 80e17780 00000000 80386998 807a0000 00000000 00400040 8038f848
807623b8 80d61ab8 00000004 80e17780 00000000 803a68e4 80c25e2c 803bb884
...
Call Trace:
[<803ab00c>] serial_base_ctrl_add+0x78/0xf4
[<803aa644>] serial_core_register_port+0x174/0x69c
[<8077e9ac>] zs_init+0xc8/0xfc
[<800404d4>] do_one_initcall+0x40/0x2ac
[<8076cecc>] kernel_init_freeable+0x1e4/0x270
[<80605bec>] kernel_init+0x20/0x108
[<800431e8>] ret_from_kernel_thread+0x14/0x1c
Code: 2442aeb0 ae120024 ae0200d0 <8c67002c> 50e00001 8c670000 3c06806e 3c05806e afb30010
---[ end trace 0000000000000000 ]---
(report at the offending commit) -- where a pointer is dereferenced that
has been derived from a null pointer to the port's parent device.
Since no device is available with legacy probing and it's not anymore a
preferable way to discover devices anyway, switch the driver to using a
platform device and use it as the port's parent device. Update resource
handling accordingly and only request the actual span of addresses used
within the slot, which will have had its resource already requested by
generic platform device code.
Use platform_driver_probe() not just because SCC devices are fixed with
solder on board and not straightforward to remove, but foremost because
the associated TTY's major device number is the same as used by the dz
driver and the first driver to claim it will prevent the other one from
using it. Either one DZ device or some SCC devices will be present in a
given system but never both at a time, and therefore we want the major
device number to be claimed by the first driver to actually successfully
bind to its device and platform_driver_probe() is a way to fulfil that.
An unfortunate consequence of the switch to a platform device is we now
hand the console over from the bootconsole much later in the bootstrap.
The firmware console handler appears good enough though to work so late
and in particular with interrupts enabled.
Since there is one way only remaining to reach zs_reset() now, remove
the port initialisation marker as no longer needed and go through the
channel reset unconditionally.
Fixes: 84a9582fd203 ("serial: core: Start managing serial controllers to enable runtime PM")
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Cc: stable@vger.kernel.org # needs to use .remove_new for <= 6.10
Link: https://patch.msgid.link/alpine.DEB.2.21.2605062328480.46195@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Prevent a crash from happening as the first serial port is initialised:
Console: switching to colour frame buffer device 160x64
tgafb: SFB+ detected, rev=0x02
fb0: Digital ZLX-E1 frame buffer device at 0x1e000000
DECstation DZ serial driver version 1.04
CPU 0 Unable to handle kernel paging request at virtual address 000000bc, epc == 8048b3a4, ra == 80470a78
Oops[#1]:
CPU: 0 UID: 0 PID: 1 Comm: swapper/0 Not tainted 6.19.0-dirty #35 NONE
$ 0 : 00000000 1000ac00 00000004 804707ac
$ 4 : 00000000 80e20850 80e20858 81000030
$ 8 : 00000000 8072c81c 00000008 fefefeff
$12 : 6c616972 00000006 80c5917f 69726420
$16 : 80e20800 00000000 808f8968 80e20800
$20 : 00000000 807f5a90 808b0094 808d3bc8
$24 : 00000018 80479030
$28 : 80c2e000 80c2fd70 00000069 80470a78
Hi : 00000004
Lo : 00000000
epc : 8048b3a4 __dev_fwnode+0x0/0xc
ra : 80470a78 serial_base_ctrl_add+0xa0/0x168
Status: 1000ac04 IEp
Cause : 30000008 (ExcCode 02)
BadVA : 000000bc
PrId : 00000220 (R3000)
Modules linked in:
Process swapper/0 (pid: 1, threadinfo=(ptrval), task=(ptrval), tls=00000000)
Stack : 00400044 00400040 8046f4cc 00000000 808a6148 808a0000 808f8968 8086983c
808e0000 8046fc84 1000ac01 00000028 80e20700 802ba3f8 80e20700 80d34a94
80c1b900 80e20700 80e20700 80e20700 80e20700 80444650 00000000 00000000
00000000 807f5a90 808b0094 80447080 00400040 808e0000 80d34a94 808a6148
80d34a94 00000004 80e20700 00000000 8076974c 80469810 80c2fe3c 1000ac01
...
Call Trace:
[<8048b3a4>] __dev_fwnode+0x0/0xc
[<80470a78>] serial_base_ctrl_add+0xa0/0x168
[<8046fc84>] serial_core_register_port+0x1c8/0x974
[<808c6af0>] dz_init+0x74/0xc8
[<800470e0>] do_one_initcall+0x44/0x2d4
[<808b111c>] kernel_init_freeable+0x258/0x308
[<8072e434>] kernel_init+0x20/0x114
[<80049cd0>] ret_from_kernel_thread+0x14/0x1c
Code: 27bd0018 03e00008 2402ffea <8c8200bc> 03e00008 00000000 27bdffc0 afbe0038 afb30024
---[ end trace 0000000000000000 ]---
-- where a pointer is dereferenced that has been derived from a null
pointer to the port's parent device.
Since no device is available with legacy probing and it's not anymore a
preferable way to discover devices anyway, switch the driver to using a
platform device and use it as the port's parent device. Update resource
handling accordingly and only request the actual span of addresses used
within the slot, which will have had its resource already requested by
generic platform device code.
Use platform_driver_probe() not just because the DZ device is fixed with
solder on board and not straightforward to remove, but foremost because
the associated TTY's major device number is the same as used by the zs
driver and the first driver to claim it will prevent the other one from
using it. Either one DZ device or some SCC devices will be present in a
given system but never both at a time, and therefore we want the major
device number to be claimed by the first driver to actually successfully
bind to its device and platform_driver_probe() is a way to fulfil that.
An unfortunate consequence of the switch to a platform device is we now
hand the console over from the bootconsole much later in the bootstrap.
The firmware console handler appears good enough though to work so late
and in particular with interrupts enabled.
Conversely only starting the console port so late lets the reset code
fully utilise our delay handlers, so switch from udelay() to fsleep()
for transmitter draining so as to avoid busy-waiting for an excessive
amount of time.
Fixes: 84a9582fd203 ("serial: core: Start managing serial controllers to enable runtime PM")
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Cc: stable@vger.kernel.org # needs to use .remove_new for <= 6.10
Link: https://patch.msgid.link/alpine.DEB.2.21.2605062326540.46195@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Switch the driver to using the channel reset rather than hardware reset,
simplifying handling by removing an interference between channels that
causes the other channel to become uninitialised afterwards.
There is little difference between the two kinds of reset in terms of
register settings that result, and we initialise the whole register set
right away anyway. However this prevents a hang from happening should
the console output handler in the firmware try to access the other port
whose transmitter has been disabled and line parameters messed up.
For example this will happen if the keyboard port (port A) is chosen for
the system console, unusually but not insanely for a headless system, as
the port is wired to a standard DA-15 connector and an adapter can be
easily made. Or with the next change in place this would happen for the
regular console port (port B), since the keyboard port (port A) will be
initialised first.
Just remove the unnecessary complication then, a channel reset is good
enough. We still need the initialisation marker, now per channel rather
than per SCC, as for the console port zs_reset() will be called twice:
once early on via zs_serial_console_init() for the console setup only,
and then again via zs_config_port() as the port is associated with a TTY
device.
Fixes: 8b4a40809e53 ("zs: move to the serial subsystem")
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Cc: stable@vger.kernel.org # v2.6.23+
Link: https://patch.msgid.link/alpine.DEB.2.21.2605062323430.46195@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Calling zs_reset() in the course of setting up the serial device causes
line parameters to be reset and the transmitter disabled. We've been
lucky in that no message is usually produced to the kernel log between
this call and the later call to uart_set_options() in the course of
console setup done by zs_serial_console_init(), or the system would hang
as the console output handler in the firmware tried to access a port the
transmitter of which has been disabled and line parameters messed up.
This will change with the next change to the driver, so fix zs_reset()
such that line parameters are set for 9600n8 console operation as with
the system firmware and the transmitter re-enabled after reset. This
also means zs_pm() serves no purpose anymore, so drop it.
Fixes: 8b4a40809e53 ("zs: move to the serial subsystem")
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Cc: stable@vger.kernel.org # v2.6.23+
Link: https://patch.msgid.link/alpine.DEB.2.21.2605062308040.46195@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Calling dz_reset() in the course of setting up the serial device causes
line parameters to be reset and the transmitter disabled. We've been
lucky in that no message is usually produced to the kernel log between
this call and the later call to uart_set_options() in the course of
console setup done by dz_serial_console_init(), or the system would hang
as the console output handler in the firmware tried to access a port the
transmitter of which has been disabled and line parameters messed up.
This will change with the next change to the driver, so fix dz_reset()
such that line parameters are set for 9600n8 console operation as with
the system firmware and the transmitter re-enabled after reset. This
also means dz_pm() serves no purpose anymore, so drop it.
Fixes: e6ee512f5a77 ("dz.c: Resource management")
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Cc: stable@vger.kernel.org # v2.6.25+
Link: https://patch.msgid.link/alpine.DEB.2.21.2605062302010.46195@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In the DZ interface as implemented by the DC7085 gate array the serial
transmitters are double buffered, meaning that at the time a transmitter
is ready to accept the next character there is one in the transmit shift
register still being sent to the line. Issuing a master clear at this
time causes this character to be lost, so wait an extra amount of time
sufficient for the transmit shift register to drain at 9600bps, which is
the baud rate setting used by the firmware console.
Mind the specified 1.4us TRDY recovery time in the course and continue
using iob() as the completion barrier, since the platforms involved use
a write buffer that can delay and combine writes, and reorder them with
respect to reads regardless of the MMIO locations accessed and we still
lack a platform-independent handler for that.
When called from dz_serial_console_init() this is too early for fsleep()
to work and even before lpj has been calculated and therefore the delay
is actually not sufficient for the transmitter to drain and is merely a
placeholder now. This will be addressed in a follow-up change.
Fixes: e6ee512f5a77 ("dz.c: Resource management")
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Cc: stable@vger.kernel.org # v2.6.25+
Link: https://patch.msgid.link/alpine.DEB.2.21.2605062259080.46195@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
dw8250_handle_irq() calls serial8250_handle_irq_locked() with the port
lock held via guard(uart_port_lock_irqsave). The guard destructor is
plain uart_port_unlock_irqrestore(), so a SysRq character captured into
port->sysrq_ch by uart_prepare_sysrq_char() is dropped without ever
being dispatched to handle_sysrq().
This is the same regression pattern as in serial8250_handle_irq(),
introduced when 883c5a2bc934 ("serial: 8250_dw: Rework
dw8250_handle_irq() locking and IIR handling") moved the function to
the guard()-based locking scheme without using the sysrq-aware unlock
helper.
Switch to guard(uart_port_lock_check_sysrq_irqsave) so that captured
sysrq_ch is dispatched on scope exit, matching the fix in
serial8250_handle_irq().
Fixes: 883c5a2bc934 ("serial: 8250_dw: Rework dw8250_handle_irq() locking and IIR handling")
Cc: stable@vger.kernel.org
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Jacques Nilo <jnilo@free.fr>
Link: https://patch.msgid.link/ed56fcaf4af24e4ed011a7bce206e0182acb761c.1778675349.git.jnilo@free.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
serial8250_handle_irq() captures a SysRq character into port->sysrq_ch
inside serial8250_handle_irq_locked() via uart_prepare_sysrq_char()
(reached from serial8250_read_char()). Dispatch of that captured
character to handle_sysrq() is expected to happen at port-unlock time,
through uart_unlock_and_check_sysrq[_irqrestore]().
After commit 8324a54f604d ("serial: 8250: Add
serial8250_handle_irq_locked()") the function was reduced to a wrapper
that takes the port lock via guard(uart_port_lock_irqsave) whose
destructor is plain uart_port_unlock_irqrestore(). The sysrq-aware
unlock helper is no longer called, so port->sysrq_ch is captured but
never dispatched: BREAK + SysRq key is consumed silently.
This was the very condition Johan Hovold's 853a9ae29e978 ("serial:
8250: fix handle_irq locking", 2021) introduced
uart_unlock_and_check_sysrq_irqrestore() to address.
Switch to the new guard(uart_port_lock_check_sysrq_irqsave), whose
destructor is the sysrq-aware unlock helper, restoring the pre-split
behaviour. Update the Context: comment on serial8250_handle_irq_locked()
so future HW-specific 8250 wrappers know to use the same guard or the
explicit sysrq-aware unlock.
Verified on RTL8196E with CONFIG_MAGIC_SYSRQ_SERIAL=y: BREAK + 'h' on
the console UART produces the SysRq help dump in dmesg and the brk
counter in /proc/tty/driver/serial increments correctly.
Fixes: 8324a54f604d ("serial: 8250: Add serial8250_handle_irq_locked()")
Cc: stable@vger.kernel.org
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Jacques Nilo <jnilo@free.fr>
Link: https://patch.msgid.link/52692ae6c3501f7940347cef364ad7fcacaab7e5.1778675349.git.jnilo@free.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Sashiko identified a deadlock when the console flow is engaged [1].
When console flow control is enabled (UPF_CONS_FLOW),
s3c24xx_serial_stop_tx() calls s3c24xx_serial_rx_enable() and
s3c24xx_serial_start_tx() calls s3c24xx_serial_rx_disable().
The serial core framework invokes the .stop_tx() and .start_tx()
callbacks with the port->lock spinlock already held. Furthermore, all
internal driver paths that invoke stop_tx (such as the DMA TX
completion handler s3c24xx_serial_tx_dma_complete() or the PIO TX IRQ
handler s3c24xx_serial_tx_irq()) also acquire port->lock prior to
calling it. (Note that s3c24xx_serial_start_tx() is only invoked by the
serial core).
However, s3c24xx_serial_rx_enable() and s3c24xx_serial_rx_disable()
unconditionally attempt to acquire port->lock again using
uart_port_lock_irqsave(). Since spinlocks are not recursive, this
causes a deadlock on the same CPU when console flow control is engaged.
Remove the redundant lock acquisition from both rx helper functions.
Cc: stable <stable@kernel.org>
Fixes: b497549a035c ("[ARM] S3C24XX: Split serial driver into core and per-cpu drivers")
Reported-by: John Ogness <john.ogness@linutronix.de>
Closes: https://sashiko.dev/#/patchset/20260506121606.5805-1-john.ogness%40linutronix.de [1]
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://patch.msgid.link/20260515-samsung-tty-flow-control-deadlock-v1-1-93255edbc9bc@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
altera_jtaguart_probe() maps the register window before registering the
UART port, but it ignores failures from uart_add_one_port(). If port
registration fails, probe still returns success and the mapping remains
live until a later remove path that is not part of probe failure cleanup.
Return the uart_add_one_port() error and unmap the register window on
that failure path.
This issue was identified during our ongoing static-analysis research while
reviewing kernel code.
Fixes: 5bcd601049c6 ("serial: Add driver for the Altera JTAG UART")
Cc: stable <stable@kernel.org>
Co-developed-by: Ijae Kim <ae878000@gmail.com>
Signed-off-by: Ijae Kim <ae878000@gmail.com>
Signed-off-by: Myeonghun Pak <mhun512@gmail.com>
Link: https://patch.msgid.link/20260512065837.79528-1-mhun512@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There are rare cases in which the host gets stuck in the ISR because it
is flooded with messages during the startup phase.
The reason for the soft lockup in the ISR is the missing FIFO error IRQ
(FIFOE) handling. Not handling it and reporting IRQ_HANDLED triggers
the IRQ immediately again.
Fix this by adding a check for the FIFOE status and clearing the FIFO
if no data is ready (DR).
This behavior was observed on an AM62L device which uses the OMAP 8250
driver. Fix it for all 8250 drivers, since the OMAP driver's special
IRQ setup handling may trigger this behavior more frequently, but it
is not ensured that other 8250 drivers aren't affected.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Link: https://patch.msgid.link/20260519-v7-1-topic-serial-8250-v1-1-56b04293a246@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The plain text binding file was superseded by the YAML schema in
commit d50f974c4f7f ("dt-bindings: serial: Convert rs485 bindings
to json-schema"). The file now contains only a redirect notice.
Remove it, and update references in serial_core.c and
serial-rs485.rst to point to the YAML schema.
Signed-off-by: Akash Sukhavasi <akash.sukhavasi@gmail.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://patch.msgid.link/20260521162137.6325-1-akash.sukhavasi@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
While being less compact, using named initializers allows to more easily
see which members of the structs are assigned which value without having
to lookup the declaration of the struct. And it's also more robust
against changes to the struct definition.
The mentioned robustness is relevant for a planned change to struct
i2c_device_id that replaces .driver_data by an anonymous union.
While touching all these arrays, unify usage of whitespace in the list
terminator.
This patch doesn't modify the compiled arrays, only their representation
in source form benefits. The former was confirmed with x86 and arm64
builds.
Signed-off-by: Uwe Kleine-König (The Capable Hub) <u.kleine-koenig@baylibre.com>
Link: https://patch.msgid.link/20260518101456.632410-2-u.kleine-koenig@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The clock notifier and matching work_struct in dw8250_data were added
in 2020 for the Baikal-T1 SoC, whose multiple UART ports share a
single reference clock and need to be informed when another consumer
re-rates that clock.
Baikal SoC support has since been removed from the kernel (see e.g.
commit 5d6c477687ae ("clk: baikal-t1: Remove not-going-to-be-supported
code for Baikal SoC") and the matching removals across bus/, mtd/,
PCI/, hwmon/, memory/). No remaining in-tree user needs the
cross-device baudclk rate-change notification path: the only
configuration that wired up the notifier was Baikal-T1's shared
reference clock topology.
Drop the now-unused clock-notifier and its deferred-update worker:
- struct dw8250_data fields clk_notifier and clk_work,
- the clk_to_dw8250_data() and work_to_dw8250_data() helpers,
- the dw8250_clk_work_cb() and dw8250_clk_notifier_cb() callbacks,
- the INIT_WORK / notifier_call setup in dw8250_probe(),
- the clk_notifier_register() / queue_work() in dw8250_probe(),
- the matching clk_notifier_unregister() / flush_work() in
dw8250_remove(),
- the stale comment in dw8250_set_termios() about the worker
blocking,
- the linux/notifier.h and linux/workqueue.h includes that are
no longer used.
dw8250_set_termios() keeps calling clk_set_rate() directly, which is
all the remaining single-UART configurations require.
Signed-off-by: Stepan Ionichev <sozdayvek@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20260514143746.23671-3-sozdayvek@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
dw8250_probe() registers the 8250 port via serial8250_register_8250_port()
and then, if the device has a clock, registers a clock notifier. If
clk_notifier_register() fails, probe returns the error but leaves the
8250 port registered. The matching serial8250_unregister_port() lives
in dw8250_remove(), which is not called when probe fails, so the port
slot stays occupied until the device is rebound or the system is
rebooted. The devm-allocated driver data is freed while the port still
references it (via the saved private_data and serial_in/serial_out
callbacks), so any access to that port slot before a rebind is a
use-after-free hazard.
Unregister the port on the clk_notifier_register() error path.
Fixes: cc816969d7b5 ("serial: 8250_dw: Fix common clocks usage race condition")
Cc: stable@vger.kernel.org
Signed-off-by: Stepan Ionichev <sozdayvek@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20260514143746.23671-2-sozdayvek@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This is based on code removed in commit 89d4f98ae90d ("ARM: remove zte
zx platform"). I did not bring back the zx29-uart .compatible as the
arm,primecell-periphid does the job.
Reviewed-by: Linus Walleij <linusw@kernel.org>
Signed-off-by: Stefan Dösinger <stefandoesinger@gmail.com>
Link: https://patch.msgid.link/20260514-zx29uart-v1-2-68470ecc3977@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The kernel documentation specifies that the console option 'r' can
be used to enable hardware flow control for console writes. The 8250
driver does include code for hardware flow control on the console if
cons_flow is set, but there is no code path that actually sets this.
However, that is not the only issue. The problems are:
1. Specifying the console option 'r' does not lead to cons_flow being
set.
2. Even if cons_flow would be set, serial8250_register_8250_port()
clears it.
3. When the console option 'r' is specified, uart_set_options()
attempts to initialize the port for CRTSCTS. However, afterwards
it does not set the UPSTAT_CTS_ENABLE status bit and therefore on
boot, uart_cts_enabled() is always false. This policy bit is
important for console drivers as a criteria if they may poll CTS.
4. Even though uart_set_options() attempts to initialize the port
for CRTSCTS, the 8250 set_termios() callback does not enable the
RTS signal (TIOCM_RTS) and thus the hardware is not properly
initialized for CTS polling.
5. Even if modem control was properly setup for CTS polling
(TIOCM_RTS), uart_configure_port() clears TIOCM_RTS, thus
breaking CTS polling.
6. wait_for_xmitr() and serial8250_console_write() use cons_flow
to decide if CTS polling should occur. However, the condition
should also include a check that it is not in RS485 mode and
CRTSCTS is actually enabled in the hardware.
Address all these issues as conservatively as possible by gating them
behind checks focussed on the user specifying console hardware flow
control support and the hardware being configured for CTS polling
at the time of the write to the UART.
Since checking the UPSTAT_CTS_ENABLE status bit is a part of the new
condition gate, these changes also support runtime termios updates to
disable/enable CRTSCTS.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://patch.msgid.link/20260511152706.151498-4-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
