| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Add support for ref-sync pair registration using the 'ref-sync-sources'
phandle property from device tree. A ref-sync pair consists of a clock
reference and a low-frequency sync signal where the DPLL locks to the
clock reference but phase-aligns to the sync reference.
The implementation:
- Stores fwnode handle in zl3073x_dpll_pin during pin registration
- Adds ref_sync_get/set callbacks to read and write the sync control
mode and pair registers
- Validates ref-sync frequency constraints: sync signal must be 8 kHz
or less, clock reference must be 1 kHz or more and higher than sync
- Excludes sync source from automatic reference selection by setting
its priority to NONE on connect; on disconnect the priority is left
as NONE and the user must explicitly make the pin selectable again
- Iterates ref-sync-sources phandles to register declared pairings
via dpll_pin_ref_sync_pair_add()
Reviewed-by: Petr Oros <poros@redhat.com>
Reviewed-by: Prathosh Satish <Prathosh.Satish@microchip.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Link: https://patch.msgid.link/20260408102716.443099-6-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add ZL_REF_SYNC_CTRL_MODE_REFSYNC_PAIR and ZL_REF_SYNC_CTRL_PAIR
register definitions.
Add inline helpers to get and set the sync control mode and sync pair
fields of the reference sync control register:
zl3073x_ref_sync_mode_get/set() - ZL_REF_SYNC_CTRL_MODE field
zl3073x_ref_sync_pair_get/set() - ZL_REF_SYNC_CTRL_PAIR field
Add inline helpers to get and set the clock type field of the output
mode register:
zl3073x_out_clock_type_get/set() - ZL_OUTPUT_MODE_CLOCK_TYPE field
Convert existing esync callbacks to use the new helpers.
Reviewed-by: Petr Oros <poros@redhat.com>
Reviewed-by: Prathosh Satish <Prathosh.Satish@microchip.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Link: https://patch.msgid.link/20260408102716.443099-4-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Replace open-coded clear-and-set bitfield operations with
FIELD_MODIFY().
Reviewed-by: Petr Oros <poros@redhat.com>
Reviewed-by: Prathosh Satish <Prathosh.Satish@microchip.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Link: https://patch.msgid.link/20260408102716.443099-3-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Return -EOPNOTSUPP early in esync_get callbacks when esync is not
supported instead of conditionally populating the range at the end.
This simplifies the control flow by removing the finish label/goto
in the output variant and the conditional range assignment in both
input and output variants.
Replace open-coded N-div signal format switch statements with
zl3073x_out_is_ndiv() helper in esync_get, esync_set and
frequency_set callbacks.
Reviewed-by: Petr Oros <poros@redhat.com>
Reviewed-by: Prathosh Satish <Prathosh.Satish@microchip.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Link: https://patch.msgid.link/20260408102716.443099-2-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Extract common measurement latch logic from zl3073x_ref_ffo_update()
into a new zl3073x_ref_freq_meas_latch() helper and add
zl3073x_ref_freq_meas_update() that uses it to latch and read absolute
input reference frequencies in Hz.
Add meas_freq field to struct zl3073x_ref and the corresponding
zl3073x_ref_meas_freq_get() accessor. The measured frequencies are
updated periodically alongside the existing FFO measurements.
Add freq_monitor boolean to struct zl3073x_dpll and implement the
freq_monitor_set/get device callbacks to enable/disable frequency
monitoring via the DPLL netlink interface.
Implement measured_freq_get pin callback for input pins that returns the
measured input frequency in mHz.
Reviewed-by: Petr Oros <poros@redhat.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Link: https://patch.msgid.link/20260402184057.1890514-4-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The HW reports the currently selected reference in the
dpll_refsel_status register regardless of the DPLL mode. Use this to
delete zl3073x_dpll_selected_ref_get() and have callers read the
register directly via the cached channel state.
Simplify zl3073x_dpll_connected_ref_get() to check refsel_state for
LOCK directly and return the reference index, changing the return
type from int to u8. The redundant ref_is_status_ok check is removed
since the DPLL cannot be in LOCK state with a failed reference.
In zl3073x_dpll_mode_set(), replace the selected_ref_get() call with
zl3073x_chan_refsel_ref_get() to read the currently selected
reference directly from the cached channel state.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Link: https://patch.msgid.link/20260315174224.399074-7-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cache the ZL_REG_DPLL_REF_PRIO registers in the zl3073x_chan cfg group.
These mailbox-based registers store per-reference priority values
(4 bits each, P/N packed) used for automatic reference selection.
Add ref_prio[] array to struct zl3073x_chan and provide inline helpers
zl3073x_chan_ref_prio_get(), zl3073x_chan_ref_prio_set(), and
zl3073x_chan_ref_is_selectable() for nibble-level access and priority
queries. Extend state_fetch and state_set with DPLL mailbox operations
to read and write the priority registers.
Replace the ad-hoc zl3073x_dpll_ref_prio_get/set functions in dpll.c
with the cached state pattern, removing direct mailbox access from
the DPLL layer. This also simplifies pin registration since reading
priority from cached state cannot fail.
Remove the pin->selectable flag from struct zl3073x_dpll_pin and
derive the selectable state from the cached ref priority via
zl3073x_chan_ref_is_selectable(), eliminating a redundant cache.
Inline zl3073x_dpll_selected_ref_set() into
zl3073x_dpll_input_pin_state_on_dpll_set(), unifying all manual and
automatic mode paths to commit changes through a single
zl3073x_chan_state_set() call at the end of the function.
Move hardware limit constants from core.h to regs.h so that chan.h
can reference ZL3073X_NUM_REFS for the ref_prio array size.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Link: https://patch.msgid.link/20260315174224.399074-6-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add mon_status and refsel_status fields to struct zl3073x_chan in a
stat group to cache the 'dpll_mon_status' and 'dpll_refsel_status'
registers.
Add zl3073x_chan_lock_state_get(), zl3073x_chan_is_ho_ready(),
zl3073x_chan_refsel_state_get() and zl3073x_chan_refsel_ref_get()
inline helpers for reading cached state, and zl3073x_chan_state_update()
for refreshing both registers from hardware. Call it from
zl3073x_chan_state_fetch() as well so that channel status is
initialized at device startup.
Call zl3073x_dev_chan_states_update() from the periodic work to
keep the cached state up to date and convert
zl3073x_dpll_lock_status_get() and zl3073x_dpll_selected_ref_get()
to use the cached state via the new helpers instead of direct register
reads.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Link: https://patch.msgid.link/20260315174224.399074-5-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Extract DPLL channel state management into a dedicated zl3073x_chan
module, following the pattern already established by zl3073x_ref,
zl3073x_out and zl3073x_synth.
The new struct zl3073x_chan caches the raw mode_refsel register value
in a cfg group with inline getters and setters to extract and update
the bitfields. Three standard state management functions are provided:
- zl3073x_chan_state_fetch: read the mode_refsel register from HW
- zl3073x_chan_state_get: return cached channel state
- zl3073x_chan_state_set: write changed state to HW, skip if unchanged
The channel state array chan[ZL3073X_MAX_CHANNELS] is added to struct
zl3073x_dev. Channel state is fetched as part of
zl3073x_dev_state_fetch, using the chip-specific channel count.
The refsel_mode and forced_ref fields are removed from struct
zl3073x_dpll and all direct register accesses in dpll.c are replaced
with the new chan state operations.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Link: https://patch.msgid.link/20260315174224.399074-4-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Extract the per-reference monitor status HW read into a dedicated
zl3073x_ref_state_update() helper in the ref module. Rename
zl3073x_dev_ref_status_update() to zl3073x_dev_ref_states_update()
and use the new helper in it. Call it from zl3073x_ref_state_fetch()
as well so that mon_status is initialized at device startup. This
keeps direct register access and struct field writes behind the ref
module's interface, consistent with the state management pattern
used for other ref operations.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Link: https://patch.msgid.link/20260315174224.399074-3-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Organize the zl3073x_out, zl3073x_ref, and zl3073x_synth structures
using struct_group() to partition fields into semantic groups:
* cfg: mutable configuration written to HW via state_set
* inv: invariant fields set once during state_fetch
* stat: read-only status
This enables group-level operations in place of field-by-field copies:
* state_set validates invariants haven't changed (WARN_ON + -EINVAL)
* state_set short-circuits when cfg is unchanged
* state_set copy entire groups in a single assignment instead of
enumerating each field
Add kernel doc for zl3073x_out_state_set and zl3073x_ref_state_set
documenting the new invariant validation and short-circuit semantics.
Remove forward declaration of zl3073x_synth_state_set().
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Link: https://patch.msgid.link/20260315174224.399074-2-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Some zl3073x chip variants (0x1Exx, 0x2Exx and 0x3FC4) provide a die
temperature status register with 0.1 C resolution.
Add a ZL3073X_FLAG_DIE_TEMP chip flag to identify these variants and
implement zl3073x_dpll_temp_get() as the dpll_device_ops.temp_get
callback. The register value is converted from 0.1 C units to
millidegrees as expected by the DPLL subsystem.
To support per-instance ops selection, copy the base dpll_device_ops
into struct zl3073x_dpll and conditionally set .temp_get during device
registration based on the chip flag.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Link: https://patch.msgid.link/20260227105300.710272-3-ivecera@redhat.com
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Replace the five per-variant zl3073x_chip_info structures and their
exported symbol definitions with a single consolidated chip ID lookup
table. The chip variant is now detected at runtime by reading the chip
ID register from hardware and looking it up in the table, rather than
being selected at compile time via the bus driver match data.
Repurpose struct zl3073x_chip_info to hold a single chip ID, its
channel count, and a flags field. Introduce enum zl3073x_flags with
ZL3073X_FLAG_REF_PHASE_COMP_32 to replace the chip_id switch statement
in zl3073x_dev_is_ref_phase_comp_32bit(). Store a pointer to the
detected chip_info entry in struct zl3073x_dev for runtime access.
This simplifies the bus drivers by removing per-variant .data and
.driver_data references from the I2C/SPI match tables, and makes
adding support for new chip variants a single-line table addition.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Link: https://patch.msgid.link/20260227105300.710272-2-ivecera@redhat.com
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Including fixes from IPsec, Bluetooth and netfilter
Current release - regressions:
- wifi: fix dev_alloc_name() return value check
- rds: fix recursive lock in rds_tcp_conn_slots_available
Current release - new code bugs:
- vsock: lock down child_ns_mode as write-once
Previous releases - regressions:
- core:
- do not pass flow_id to set_rps_cpu()
- consume xmit errors of GSO frames
- netconsole: avoid OOB reads, msg is not nul-terminated
- netfilter: h323: fix OOB read in decode_choice()
- tcp: re-enable acceptance of FIN packets when RWIN is 0
- udplite: fix null-ptr-deref in __udp_enqueue_schedule_skb().
- wifi: brcmfmac: fix potential kernel oops when probe fails
- phy: register phy led_triggers during probe to avoid AB-BA deadlock
- eth:
- bnxt_en: fix deleting of Ntuple filters
- wan: farsync: fix use-after-free bugs caused by unfinished tasklets
- xscale: check for PTP support properly
Previous releases - always broken:
- tcp: fix potential race in tcp_v6_syn_recv_sock()
- kcm: fix zero-frag skb in frag_list on partial sendmsg error
- xfrm:
- fix race condition in espintcp_close()
- always flush state and policy upon NETDEV_UNREGISTER event
- bluetooth:
- purge error queues in socket destructors
- fix response to L2CAP_ECRED_CONN_REQ
- eth:
- mlx5:
- fix circular locking dependency in dump
- fix "scheduling while atomic" in IPsec MAC address query
- gve: fix incorrect buffer cleanup for QPL
- team: avoid NETDEV_CHANGEMTU event when unregistering slave
- usb: validate USB endpoints"
* tag 'net-7.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (72 commits)
netfilter: nf_conntrack_h323: fix OOB read in decode_choice()
dpaa2-switch: validate num_ifs to prevent out-of-bounds write
net: consume xmit errors of GSO frames
vsock: document write-once behavior of the child_ns_mode sysctl
vsock: lock down child_ns_mode as write-once
selftests/vsock: change tests to respect write-once child ns mode
net/mlx5e: Fix "scheduling while atomic" in IPsec MAC address query
net/mlx5: Fix missing devlink lock in SRIOV enable error path
net/mlx5: E-switch, Clear legacy flag when moving to switchdev
net/mlx5: LAG, disable MPESW in lag_disable_change()
net/mlx5: DR, Fix circular locking dependency in dump
selftests: team: Add a reference count leak test
team: avoid NETDEV_CHANGEMTU event when unregistering slave
net: mana: Fix double destroy_workqueue on service rescan PCI path
MAINTAINERS: Update maintainer entry for QUALCOMM ETHQOS ETHERNET DRIVER
dpll: zl3073x: Remove redundant cleanup in devm_dpll_init()
selftests/net: packetdrill: Verify acceptance of FIN packets when RWIN is 0
tcp: re-enable acceptance of FIN packets when RWIN is 0
vsock: Use container_of() to get net namespace in sysctl handlers
net: usb: kaweth: validate USB endpoints
...
|
|
The devm_add_action_or_reset() function already executes the cleanup
action on failure before returning an error, so the explicit goto error
and subsequent zl3073x_dev_dpll_fini() call causes double cleanup.
Fixes: ebb1031c5137 ("dpll: zl3073x: Refactor DPLL initialization")
Reviewed-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: Felix Gu <ustc.gu@gmail.com>
Link: https://patch.msgid.link/20260224-dpll-v2-1-d7786414a830@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The REF_PHASE_OFFSET_COMP register is 48-bit wide on most zl3073x chip
variants, but only 32-bit wide on chip IDs 0x0E30, 0x0E93..0x0E97 and
0x1F60. The driver unconditionally uses 48-bit read/write operations,
which on 32-bit variants causes reading 2 bytes past the register
boundary (corrupting the value) and writing 2 bytes into the adjacent
register.
Fix this by storing the chip ID in the device structure during probe
and adding a helper to detect the affected variants. Use the correct
register width for read/write operations and the matching sign extension
bit (31 vs 47) when interpreting the phase compensation value.
Fixes: 6287262f761e ("dpll: zl3073x: Add support to adjust phase")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260220155755.448185-1-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This was done entirely with mindless brute force, using
git grep -l '\<k[vmz]*alloc_objs*(.*, GFP_KERNEL)' |
xargs sed -i 's/\(alloc_objs*(.*\), GFP_KERNEL)/\1)/'
to convert the new alloc_obj() users that had a simple GFP_KERNEL
argument to just drop that argument.
Note that due to the extreme simplicity of the scripting, any slightly
more complex cases spread over multiple lines would not be triggered:
they definitely exist, but this covers the vast bulk of the cases, and
the resulting diff is also then easier to check automatically.
For the same reason the 'flex' versions will be done as a separate
conversion.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This is the result of running the Coccinelle script from
scripts/coccinelle/api/kmalloc_objs.cocci. The script is designed to
avoid scalar types (which need careful case-by-case checking), and
instead replace kmalloc-family calls that allocate struct or union
object instances:
Single allocations: kmalloc(sizeof(TYPE), ...)
are replaced with: kmalloc_obj(TYPE, ...)
Array allocations: kmalloc_array(COUNT, sizeof(TYPE), ...)
are replaced with: kmalloc_objs(TYPE, COUNT, ...)
Flex array allocations: kmalloc(struct_size(PTR, FAM, COUNT), ...)
are replaced with: kmalloc_flex(*PTR, FAM, COUNT, ...)
(where TYPE may also be *VAR)
The resulting allocations no longer return "void *", instead returning
"TYPE *".
Signed-off-by: Kees Cook <kees@kernel.org>
|
|
The frequency for an input reference is computed as:
frequency = freq_base * freq_mult * freq_ratio_m / freq_ratio_n
Before commit 5bc02b190a3fb ("dpll: zl3073x: Cache all reference
properties in zl3073x_ref"), zl3073x_dpll_input_pin_frequency_set()
explicitly wrote 1 to both the REF_RATIO_M and REF_RATIO_N hardware
registers whenever a new frequency was set. This ensured the FEC ratio
was always reset to 1:1 alongside the new base/multiplier values.
The refactoring in that commit introduced zl3073x_ref_freq_set() to
update the cached ref state, but this helper only sets freq_base and
freq_mult without resetting freq_ratio_m and freq_ratio_n to 1. Because
zl3073x_ref_state_set() uses a compare-and-write strategy, unchanged
ratio fields are never written to the hardware. If the device previously
had non-unity FEC ratio values, they remain in effect after a frequency
change, resulting in an incorrect computed frequency.
Explicitly set freq_ratio_m and freq_ratio_n to 1 in zl3073x_ref_freq_set()
to restore the original behavior.
Fixes: 5bc02b190a3fb ("dpll: zl3073x: Cache all reference properties in zl3073x_ref")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260216194007.680416-1-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Merge in late fixes in preparation for the net-next PR.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Ensure the current pin frequency is always present in the list of
supported frequencies reported to userspace. Previously, if the
firmware node was missing or didn't include the current operating
frequency in the supported-frequencies-hz property, the pin would
report a frequency that wasn't in its supported list.
Get the current frequency early in zl3073x_pin_props_get():
- For input pins: use zl3073x_dev_ref_freq_get()
- For output pins: use zl3073x_dev_output_pin_freq_get()
Place the current frequency at index 0 of the supported frequencies
array, then append frequencies from the firmware node (if present),
skipping any duplicate of the current frequency.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Link: https://patch.msgid.link/20260205154350.3180465-3-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Introduce zl3073x_dev_output_pin_freq_get() helper function to compute
the output pin frequency based on synthesizer frequency, output divisor,
and signal format. For N-div signal formats, the N-pin frequency is
additionally divided by esync_n_period.
Add zl3073x_out_is_ndiv() helper to check if an output is configured
in N-div mode (2_NDIV or 2_NDIV_INV signal formats).
Refactor zl3073x_dpll_output_pin_frequency_get() callback to use the
new helper, reducing code duplication and enabling reuse of the
frequency calculation logic in other contexts.
This is a preparatory change for adding current frequency to the
supported frequencies list in pin properties.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Link: https://patch.msgid.link/20260205154350.3180465-2-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The output pin phase adjustment functions incorrectly negate the phase
compensation value.
Per the ZL3073x datasheet, the output phase compensation register is
simply a signed two's complement integer where:
- Positive values move the phase later in time
- Negative values move the phase earlier in time
No negation is required. The erroneous negation caused phase adjustments
to be applied in the wrong direction.
Note that input pin phase adjustment correctly uses negation because the
hardware has an inverted convention for input references (positive moves
phase earlier, negative moves phase later).
Fixes: 6287262f761e ("dpll: zl3073x: Add support to adjust phase")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20260205181055.129768-1-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Update existing DPLL drivers to utilize the DPLL reference count
tracking infrastructure.
Add dpll_tracker fields to the drivers' internal device and pin
structures. Pass pointers to these trackers when calling
dpll_device_get/put() and dpll_pin_get/put().
This allows developers to inspect the specific references held by this
driver via debugfs when CONFIG_DPLL_REFCNT_TRACKER is enabled, aiding
in the debugging of resource leaks.
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Link: https://patch.msgid.link/20260203174002.705176-9-ivecera@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add support for the REF_TRACKER infrastructure to the DPLL subsystem.
When enabled, this allows developers to track and debug reference counting
leaks or imbalances for dpll_device and dpll_pin objects. It records stack
traces for every get/put operation and exposes this information via
debugfs at:
/sys/kernel/debug/ref_tracker/dpll_device_*
/sys/kernel/debug/ref_tracker/dpll_pin_*
The following API changes are made to support this:
1. dpll_device_get() / dpll_device_put() now accept a 'dpll_tracker *'
(which is a typedef to 'struct ref_tracker *' when enabled, or an empty
struct otherwise).
2. dpll_pin_get() / dpll_pin_put() and fwnode_dpll_pin_find() similarly
accept the tracker argument.
3. Internal registration structures now hold a tracker to associate the
reference held by the registration with the specific owner.
All existing in-tree drivers (ice, mlx5, ptp_ocp, zl3073x) are updated
to pass NULL for the new tracker argument, maintaining current behavior
while enabling future debugging capabilities.
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Co-developed-by: Petr Oros <poros@redhat.com>
Signed-off-by: Petr Oros <poros@redhat.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Link: https://patch.msgid.link/20260203174002.705176-8-ivecera@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add parsing for the "mux" string in the 'connection-type' pin property
mapping it to DPLL_PIN_TYPE_MUX.
Recognizing this type in the driver allows these pins to be taken as
parent pins for pin-on-pin pins coming from different modules (e.g.
network drivers).
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Link: https://patch.msgid.link/20260203174002.705176-6-ivecera@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Associate the registered DPLL pin with its firmware node by calling
dpll_pin_fwnode_set().
This links the created pin object to its corresponding DT/ACPI node
in the DPLL core. Consequently, this enables consumer drivers (such as
network drivers) to locate and request this specific pin using the
fwnode_dpll_pin_find() helper.
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Link: https://patch.msgid.link/20260203174002.705176-3-ivecera@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Currently, the dpll subsystem exports the fractional frequency offset
(FFO) in parts per million (ppm). This granularity is insufficient for
high-precision synchronization scenarios which often require parts per
trillion (ppt) resolution.
Add a new netlink attribute DPLL_A_PIN_FRACTIONAL_FREQUENCY_OFFSET_PPT
to expose the FFO in ppt.
Update the dpll netlink core to expect the driver-provided FFO value
to be in ppt. To maintain backward compatibility with existing userspace
tools, populate the legacy DPLL_A_PIN_FRACTIONAL_FREQUENCY_OFFSET
attribute by dividing the new ppt value by 1,000,000.
Update the zl3073x and mlx5 drivers to provide the FFO value in ppt:
- zl3073x: adjust the fixed-point calculation to produce ppt (10^12)
instead of ppm (10^6).
- mlx5: scale the existing ppm value by 1,000,000.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://patch.msgid.link/20260126162253.27890-1-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for .supported_modes_get() and .mode_set() callbacks
to enable switching between manual and automatic modes via netlink.
Implement .supported_modes_get() to report available modes based
on the current hardware configuration:
* manual mode is always supported
* automatic mode is supported unless the dpll channel is configured
in NCO (Numerically Controlled Oscillator) mode
Implement .mode_set() to handle the specific logic required when
transitioning between modes:
1) Transition to manual:
* If a valid reference is currently active, switch the hardware
to ref-lock mode (force lock to that reference).
* If no reference is valid and the DPLL is unlocked, switch to freerun.
* Otherwise, switch to Holdover.
2) Transition to automatic:
* If the currently selected reference pin was previously marked
as non-selectable (likely during a previous manual forcing
operation), restore its priority and selectability in the hardware.
* Switch the hardware to Automatic selection mode.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Prathosh Satish <Prathosh.Satish@microchip.com>
Link: https://patch.msgid.link/20260114122726.120303-4-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove several zl3073x_dev_... inline wrapper functions from core.h
as they are no longer used by any callers.
Removed functions:
* zl3073x_dev_ref_ffo_get
* zl3073x_dev_ref_is_enabled
* zl3073x_dev_synth_dpll_get
* zl3073x_dev_synth_is_enabled
* zl3073x_dev_out_signal_format_get
This is a cleanup after recent refactoring, as the remaining callers
now fetch the state object and use the base helpers directly.
Reviewed-by: Petr Oros <poros@redhat.com>
Tested-by: Prathosh Satish <Prathosh.Satish@microchip.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Link: https://patch.msgid.link/20251113074105.141379-7-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Expand the zl3073x_out structure to cache all output-related
hardware registers, including divisors, widths, embedded-sync
parameters and phase compensation.
Modify zl3073x_out_state_fetch() to read and populate all these
new fields at once, including zero-divisor checks. Refactor all
dpll "getter" functions in dpll.c to read from this new
cached state instead of performing direct register access.
Introduce a new function, zl3073x_out_state_set(), to handle
writing changes back to the hardware. This function compares the
provided state with the current cached state and writes *only* the
modified register values via a single mailbox sequence before
updating the local cache.
Refactor all dpll "setter" functions to modify a local copy of
the output state and then call zl3073x_out_state_set() to
commit the changes.
This change centralizes all output-related register I/O into
out.c, significantly reduces bus traffic, and simplifies the logic
in dpll.c.
Reviewed-by: Petr Oros <poros@redhat.com>
Tested-by: Prathosh Satish <Prathosh.Satish@microchip.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Link: https://patch.msgid.link/20251113074105.141379-6-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Expand the zl3073x_ref structure to cache all reference-related
hardware registers, including frequency components, embedded-sync
settings and phase compensation. Previously, these registers were
read on-demand from various functions in dpll.c leading to frequent
mailbox operations.
Modify zl3073x_ref_state_fetch() to read and populate all these new
fields at once. Refactor all "getter" functions in dpll.c to read
from this new cached state instead of performing direct register
access.
Remove the standalone zl3073x_dpll_input_ref_frequency_get() helper,
as its functionality is now replaced by zl3073x_ref_freq_get() which
operates on the cached state and add a corresponding zl3073x_dev_...
wrapper.
Introduce a new function, zl3073x_ref_state_set(), to handle
writing changes back to the hardware. This function compares the
provided state with the current cached state and writes *only* the
modified register values to the device via a single mailbox sequence
before updating the local cache.
Refactor all dpll "setter" functions to modify a local copy of the
ref state and then call zl3073x_ref_state_set() to commit the changes.
As a cleanup, update callers in dpll.c that already have
a struct zl3073x_ref * to use the direct helpers instead of the
zl3073x_dev_... wrappers.
This change centralizes all reference-related register I/O into ref.c,
significantly reduces bus traffic, and simplifies the logic in dpll.c.
Reviewed-by: Petr Oros <poros@redhat.com>
Tested-by: Prathosh Satish <Prathosh.Satish@microchip.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Link: https://patch.msgid.link/20251113074105.141379-5-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Instead of reading the ZL_REG_REF_MON_STATUS register every time
the reference status is needed, cache this value in the zl3073x_ref
struct.
This is achieved by:
* Adding a mon_status field to struct zl3073x_ref
* Introducing zl3073x_dev_ref_status_update() to read the status for
all references into this new cache field
* Calling this update function from the periodic work handler
* Adding zl3073x_ref_is_status_ok() and zl3073x_dev_ref_is_status_ok()
helpers to check the cached value
* Refactoring all callers in dpll.c to use the new
zl3073x_dev_ref_is_status_ok() helper, removing direct register reads
This change consolidates all status register reads into a single periodic
function and reduces I/O bus traffic in dpll callbacks.
Reviewed-by: Petr Oros <poros@redhat.com>
Tested-by: Prathosh Satish <Prathosh.Satish@microchip.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Link: https://patch.msgid.link/20251113074105.141379-4-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Refactor the zl3073x driver by splitting the logic for input
references, outputs and synthesizers out of the monolithic
core.[ch] files.
Move the logic for each functional block into its own dedicated files:
ref.[ch], out.[ch] and synth.[ch].
Specifically:
- Move state structures (zl3073x_ref, zl3073x_out, zl3073x_synth)
from core.h into their respective new headers
- Move state-fetching functions (..._state_fetch) from core.c to their
new .c files
- Move the zl3073x_ref_freq_factorize helper from core.c to ref.c
- Introduce a new helper layer to decouple the core device logic from
the state-parsing logic:
1. Move the original inline helpers (e.g., zl3073x_ref_is_enabled)
to the new headers (ref.h, etc.) and make them operate on a
const struct ... * pointer.
2. Create new zl3073x_dev_... prefixed functions in core.h
(e.g., zl3073x_dev_ref_is_enabled) and Implement these _dev_ functions
to fetch state using a new ..._state_get() helper and then call
the non-prefixed helper.
3. Update all driver-internal callers (in dpll.c, prop.c, etc.) to use
the new zl3073x_dev_... functions.
Reviewed-by: Petr Oros <poros@redhat.com>
Tested-by: Prathosh Satish <Prathosh.Satish@microchip.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Link: https://patch.msgid.link/20251113074105.141379-3-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The zl3073x_ref, zl3073x_out and zl3073x_synth structures
previously stored state that was parsed from register reads. This
included values like boolean 'enabled' flags, synthesizer selections,
and pre-calculated frequencies.
This commit refactors the state management to store the raw register
values directly in these structures. The various inline helper functions
are updated to parse these raw values on-demand using FIELD_GET.
Reviewed-by: Petr Oros <poros@redhat.com>
Tested-by: Prathosh Satish <Prathosh.Satish@microchip.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Link: https://patch.msgid.link/20251113074105.141379-2-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Documentation build reported:
Warning: drivers/dpll/zl3073x/fw.c:365 function parameter 'comp' not described in 'zl3073x_fw_component_flash'
Warning: drivers/dpll/zl3073x/fw.c:365 expecting prototype for zl3073x_flash_bundle_flash(). Prototype was for zl3073x_fw_component_flash() instead
Warning: drivers/dpll/zl3073x/fw.c:365 No description found for return value of 'zl3073x_fw_component_flash'
The kernel-doc comment above `zl3073x_fw_component_flash()` used
the wrong function name (`zl3073x_flash_bundle_flash`) and omitted
the `@comp` parameter. Update the comment to correctly document
the `zl3073x_fw_component_flash()` function and its arguments.
Signed-off-by: Kriish Sharma <kriish.sharma2006@gmail.com>
Reviewed-by: Ivan Vecera <ivecera@redhat.com>
Link: https://patch.msgid.link/20251112055642.2597450-1-kriish.sharma2006@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Output pins phase adjustment values in the device are expressed
in half synth clock cycles. Use this number of cycles as output
pins' phase adjust granularity and simplify both get/set callbacks.
Reviewed-by: Michal Schmidt <mschmidt@redhat.com>
Reviewed-by: Petr Oros <poros@redhat.com>
Tested-by: Prathosh Satish <Prathosh.Satish@microchip.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Link: https://patch.msgid.link/20251029153207.178448-3-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, the signal format of an associated output is not considered
during output pin registration. As a result, the driver registers output
pins that are disabled by the signal format configuration.
Fix this by calling zl3073x_output_pin_is_enabled() to check whether
a given output pin should be registered or not.
Fixes: 75a71ecc2412 ("dpll: zl3073x: Register DPLL devices and pins")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Link: https://patch.msgid.link/20251027140912.233152-1-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If the internal flash contains missing or corrupted configuration,
basic communication over the bus still functions, but the device
is not capable of normal operation (for example, using mailboxes).
This condition is indicated in the info register by the ready bit.
If this bit is cleared, the probe procedure times out while fetching
the device state.
Handle this case by checking the ready bit value in zl3073x_dev_start()
and skipping DPLL device and pin registration if it is cleared.
Do not report this condition as an error, allowing the devlink device
to be registered and enabling the user to flash the correct configuration.
Prior this patch:
[ 31.112299] zl3073x-i2c 1-0070: Failed to fetch input state: -ETIMEDOUT
[ 31.116332] zl3073x-i2c 1-0070: error -ETIMEDOUT: Failed to start device
[ 31.136881] zl3073x-i2c 1-0070: probe with driver zl3073x-i2c failed with error -110
After this patch:
[ 41.011438] zl3073x-i2c 1-0070: FW not fully ready - missing or corrupted config
Fixes: 75a71ecc24125 ("dpll: zl3073x: Register DPLL devices and pins")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251008141445.841113-1-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Newer firmware bundles contain a flash utility whose size exceeds
the currently allowed limit. Increase the maximum allowed size
to accommodate the newer utility version.
Without this patch:
# devlink dev flash i2c/1-0070 file fw_nosplit_v3.hex
Failed to load firmware
Flashing failed
Error: zl3073x: FW load failed: [utility] component is too big (11000 bytes)
Fixes: ca017409da694 ("dpll: zl3073x: Add firmware loading functionality")
Suggested-by: Prathosh Satish <Prathosh.Satish@microchip.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20251008141418.841053-1-ivecera@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The DPLL phase measurement block uses an exponential moving average with
a configurable averaging factor. Measurements are taken at approximately
40 Hz or at the reference frequency, whichever is lower.
Currently, factor=2 is used to prioritize fast response for dynamic
phase changes. For applications needing a stable, precise average phase
offset where rapid changes are unlikely, a higher factor is recommended.
Implement the .phase_offset_avg_factor_get/set callbacks to allow a user
to adjust this factor.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20250927084912.2343597-4-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The zl3073x_devlink_flash_prepare() function calls zl3073x_fw_free() and
the caller, zl3073x_devlink_flash_update(), also calls that same free
function so it leads to a double free. Delete the extra free.
Fixes: a1e891fe4ae8 ("dpll: zl3073x: Implement devlink flash callback")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/aNVDbcIQq4RmU_fl@stanley.mountain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use the introduced functionality to read firmware files and flash their
contents into the device's internal flash memory to implement the devlink
flash update callback.
Sample output on EDS2 development board:
# devlink -j dev info i2c/1-0070 | jq '.[][]["versions"]["running"]'
{
"fw": "6026"
}
# devlink dev flash i2c/1-0070 file firmware_fw2.hex
[utility] Prepare flash mode
[utility] Downloading image 100%
[utility] Flash mode enabled
[firmware1-part1] Downloading image 100%
[firmware1-part1] Flashing image
[firmware1-part2] Downloading image 100%
[firmware1-part2] Flashing image
[firmware1] Flashing done
[firmware2] Downloading image 100%
[firmware2] Flashing image 100%
[firmware2] Flashing done
[utility] Leaving flash mode
Flashing done
# devlink -j dev info i2c/1-0070 | jq '.[][]["versions"]["running"]'
{
"fw": "7006"
}
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com |
