diff options
55 files changed, 7496 insertions, 1046 deletions
diff --git a/Documentation/devicetree/bindings/gpio/gpio-nmk.txt b/Documentation/devicetree/bindings/gpio/gpio-nmk.txt deleted file mode 100644 index 8315ac7780ef..000000000000 --- a/Documentation/devicetree/bindings/gpio/gpio-nmk.txt +++ /dev/null @@ -1,31 +0,0 @@ -Nomadik GPIO controller - -Required properties: -- compatible : Should be "st,nomadik-gpio". -- reg : Physical base address and length of the controller's registers. -- interrupts : The interrupt outputs from the controller. -- #gpio-cells : Should be two: - The first cell is the pin number. - The second cell is used to specify optional parameters: - - bits[3:0] trigger type and level flags: - 1 = low-to-high edge triggered. - 2 = high-to-low edge triggered. - 4 = active high level-sensitive. - 8 = active low level-sensitive. -- gpio-controller : Marks the device node as a GPIO controller. -- interrupt-controller : Marks the device node as an interrupt controller. -- gpio-bank : Specifies which bank a controller owns. -- st,supports-sleepmode : Specifies whether controller can sleep or not - -Example: - - gpio1: gpio@8012e080 { - compatible = "st,nomadik-gpio"; - reg = <0x8012e080 0x80>; - interrupts = <0 120 0x4>; - #gpio-cells = <2>; - gpio-controller; - interrupt-controller; - st,supports-sleepmode; - gpio-bank = <1>; - }; diff --git a/Documentation/devicetree/bindings/gpio/st,nomadik-gpio.yaml b/Documentation/devicetree/bindings/gpio/st,nomadik-gpio.yaml new file mode 100644 index 000000000000..38d37d8f7201 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/st,nomadik-gpio.yaml @@ -0,0 +1,95 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/gpio/st,nomadik-gpio.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Nomadik GPIO controller + +description: + The Nomadik GPIO driver handles Nomadik SoC GPIO blocks. This block has also + been called ST STA2X11. On the Nomadik platform, this driver is intertwined + with pinctrl-nomadik. + +maintainers: + - Linus Walleij <linus.walleij@linaro.org> + +properties: + $nodename: + pattern: "^gpio@[0-9a-f]+$" + + compatible: + enum: + - st,nomadik-gpio + - mobileye,eyeq5-gpio + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + "#gpio-cells": + const: 2 + + gpio-controller: true + + interrupt-controller: true + + "#interrupt-cells": + const: 2 + + gpio-bank: + description: System-wide GPIO bank index. + $ref: /schemas/types.yaml#/definitions/uint32 + + st,supports-sleepmode: + description: Whether the controller can sleep or not. + $ref: /schemas/types.yaml#/definitions/flag + + clocks: + maxItems: 1 + + gpio-ranges: + maxItems: 1 + + ngpios: + minimum: 0 + maximum: 32 + + resets: + maxItems: 1 + +required: + - compatible + - reg + - interrupts + - "#gpio-cells" + - gpio-controller + - interrupt-controller + - gpio-bank + +unevaluatedProperties: false + +allOf: + - if: + properties: + compatible: + contains: + const: mobileye,eyeq5-gpio + then: + properties: + st,supports-sleepmode: false + +examples: + - | + gpio@8012e080 { + compatible = "st,nomadik-gpio"; + reg = <0x8012e080 0x80>; + interrupts = <0 120 0x4>; + #gpio-cells = <2>; + gpio-controller; + interrupt-controller; + st,supports-sleepmode; + gpio-bank = <1>; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/amlogic,meson-pinctrl-a1.yaml b/Documentation/devicetree/bindings/pinctrl/amlogic,meson-pinctrl-a1.yaml index c7df4cd34197..d9e0b2c48e84 100644 --- a/Documentation/devicetree/bindings/pinctrl/amlogic,meson-pinctrl-a1.yaml +++ b/Documentation/devicetree/bindings/pinctrl/amlogic,meson-pinctrl-a1.yaml @@ -24,7 +24,7 @@ required: - compatible patternProperties: - "^bank@[0-9a-z]+$": + "^bank@[0-9a-f]+$": $ref: amlogic,meson-pinctrl-common.yaml#/$defs/meson-gpio unevaluatedProperties: false diff --git a/Documentation/devicetree/bindings/pinctrl/amlogic,meson-pinctrl-g12a-aobus.yaml b/Documentation/devicetree/bindings/pinctrl/amlogic,meson-pinctrl-g12a-aobus.yaml index 0942ea60c6cd..108719bde0d0 100644 --- a/Documentation/devicetree/bindings/pinctrl/amlogic,meson-pinctrl-g12a-aobus.yaml +++ b/Documentation/devicetree/bindings/pinctrl/amlogic,meson-pinctrl-g12a-aobus.yaml @@ -21,7 +21,7 @@ required: - compatible patternProperties: - "^bank@[0-9a-z]+$": + "^bank@[0-9a-f]+$": $ref: amlogic,meson-pinctrl-common.yaml#/$defs/meson-gpio unevaluatedProperties: false diff --git a/Documentation/devicetree/bindings/pinctrl/amlogic,meson-pinctrl-g12a-periphs.yaml b/Documentation/devicetree/bindings/pinctrl/amlogic,meson-pinctrl-g12a-periphs.yaml index e3c8bde30559..dc277f2e2edf 100644 --- a/Documentation/devicetree/bindings/pinctrl/amlogic,meson-pinctrl-g12a-periphs.yaml +++ b/Documentation/devicetree/bindings/pinctrl/amlogic,meson-pinctrl-g12a-periphs.yaml @@ -21,7 +21,7 @@ required: - compatible patternProperties: - "^bank@[0-9a-z]+$": + "^bank@[0-9a-f]+$": $ref: amlogic,meson-pinctrl-common.yaml#/$defs/meson-gpio unevaluatedProperties: false diff --git a/Documentation/devicetree/bindings/pinctrl/amlogic,meson8-pinctrl-aobus.yaml b/Documentation/devicetree/bindings/pinctrl/amlogic,meson8-pinctrl-aobus.yaml index c1b03147e8ec..add83c676327 100644 --- a/Documentation/devicetree/bindings/pinctrl/amlogic,meson8-pinctrl-aobus.yaml +++ b/Documentation/devicetree/bindings/pinctrl/amlogic,meson8-pinctrl-aobus.yaml @@ -29,7 +29,7 @@ required: - compatible patternProperties: - "^bank@[0-9a-z]+$": + "^bank@[0-9a-f]+$": $ref: amlogic,meson-pinctrl-common.yaml#/$defs/meson-gpio unevaluatedProperties: false diff --git a/Documentation/devicetree/bindings/pinctrl/amlogic,meson8-pinctrl-cbus.yaml b/Documentation/devicetree/bindings/pinctrl/amlogic,meson8-pinctrl-cbus.yaml index 4ec85b8248fa..412bbcc276f3 100644 --- a/Documentation/devicetree/bindings/pinctrl/amlogic,meson8-pinctrl-cbus.yaml +++ b/Documentation/devicetree/bindings/pinctrl/amlogic,meson8-pinctrl-cbus.yaml @@ -29,7 +29,7 @@ required: - compatible patternProperties: - "^bank@[0-9a-z]+$": + "^bank@[0-9a-f]+$": $ref: amlogic,meson-pinctrl-common.yaml#/$defs/meson-gpio unevaluatedProperties: false diff --git a/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt index e8abbdad7b5d..0aa1a53012d6 100644 --- a/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt @@ -20,6 +20,7 @@ such as pull-up, multi drive, etc. Required properties for iomux controller: - compatible: "atmel,at91rm9200-pinctrl" or "atmel,at91sam9x5-pinctrl" or "atmel,sama5d3-pinctrl" or "microchip,sam9x60-pinctrl" + or "microchip,sam9x7-pinctrl", "microchip,sam9x60-pinctrl" - atmel,mux-mask: array of mask (periph per bank) to describe if a pin can be configured in this periph mode. All the periph and bank need to be describe. @@ -120,6 +121,7 @@ Some requirements for using atmel,at91rm9200-pinctrl binding: For each bank the required properties are: - compatible: "atmel,at91sam9x5-gpio" or "atmel,at91rm9200-gpio" or "microchip,sam9x60-gpio" + or "microchip,sam9x7-gpio", "microchip,sam9x60-gpio", "atmel,at91rm9200-gpio" - reg: physical base address and length of the controller's registers - interrupts: interrupt outputs from the controller - interrupt-controller: marks the device node as an interrupt controller diff --git a/Documentation/devicetree/bindings/pinctrl/awinic,aw9523-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/awinic,aw9523-pinctrl.yaml new file mode 100644 index 000000000000..98c310a3c63c --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/awinic,aw9523-pinctrl.yaml @@ -0,0 +1,139 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/awinic,aw9523-pinctrl.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Awinic AW9523/AW9523B I2C GPIO Expander + +maintainers: + - AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org> + +description: | + The Awinic AW9523/AW9523B I2C GPIO Expander featuring 16 multi-function + I/O, 256 steps PWM mode and interrupt support. + +properties: + compatible: + const: awinic,aw9523-pinctrl + + reg: + maxItems: 1 + + '#gpio-cells': + description: | + Specifying the pin number and flags, as defined in + include/dt-bindings/gpio/gpio.h + const: 2 + + gpio-controller: true + + gpio-ranges: + maxItems: 1 + + interrupt-controller: true + + interrupts: + maxItems: 1 + description: Specifies the INTN pin IRQ. + + '#interrupt-cells': + description: + Specifies the PIN numbers and Flags, as defined in defined in + include/dt-bindings/interrupt-controller/irq.h + const: 2 + + reset-gpios: + maxItems: 1 + +# PIN CONFIGURATION NODES +patternProperties: + '-pins$': + type: object + description: + Pinctrl node's client devices use subnodes for desired pin configuration. + Client device subnodes use below standard properties. + $ref: /schemas/pinctrl/pincfg-node.yaml + + properties: + pins: + description: + List of gpio pins affected by the properties specified in + this subnode. + items: + pattern: "^gpio([0-9]|1[0-5])$" + minItems: 1 + maxItems: 16 + + function: + description: + Specify the alternative function to be configured for the + specified pins. + + enum: [ gpio, pwm ] + + bias-disable: true + bias-pull-down: true + bias-pull-up: true + drive-open-drain: true + drive-push-pull: true + input-enable: true + input-disable: true + output-high: true + output-low: true + + required: + - pins + - function + + additionalProperties: false + +required: + - compatible + - reg + - gpio-controller + - '#gpio-cells' + - gpio-ranges + +additionalProperties: false + +examples: + # Example configuration to drive pins for a keyboard matrix + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + aw9523: gpio-expander@58 { + compatible = "awinic,aw9523-pinctrl"; + reg = <0x58>; + interrupt-parent = <&tlmm>; + interrupts = <50 IRQ_TYPE_EDGE_FALLING>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&tlmm 0 0 16>; + interrupt-controller; + #interrupt-cells = <2>; + reset-gpios = <&tlmm 51 GPIO_ACTIVE_HIGH>; + + keyboard-matrix-col-pins { + pins = "gpio8", "gpio9", "gpio10", "gpio11", + "gpio12", "gpio13", "gpio14", "gpio15"; + function = "gpio"; + input-disable; + output-low; + }; + + keyboard-matrix-row-pins { + pins = "gpio0", "gpio1", "gpio2", "gpio3", + "gpio4", "gpio5", "gpio6", "gpio7"; + function = "gpio"; + bias-pull-up; + drive-open-drain; + input-enable; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/cirrus,madera.yaml b/Documentation/devicetree/bindings/pinctrl/cirrus,madera.yaml index bb61a30321a1..482acda88e73 100644 --- a/Documentation/devicetree/bindings/pinctrl/cirrus,madera.yaml +++ b/Documentation/devicetree/bindings/pinctrl/cirrus,madera.yaml @@ -93,7 +93,8 @@ properties: input-schmitt-disable: true - input-debounce: true + input-debounce: + maxItems: 1 output-low: true diff --git a/Documentation/devicetree/bindings/pinctrl/cypress,cy8c95x0.yaml b/Documentation/devicetree/bindings/pinctrl/cypress,cy8c95x0.yaml index 7f30ec2f1e54..700ac86c26b6 100644 --- a/Documentation/devicetree/bindings/pinctrl/cypress,cy8c95x0.yaml +++ b/Documentation/devicetree/bindings/pinctrl/cypress,cy8c95x0.yaml @@ -45,7 +45,8 @@ properties: maxItems: 1 gpio-reserved-ranges: - maxItems: 1 + minItems: 1 + maxItems: 60 vdd-supply: description: @@ -85,6 +86,8 @@ patternProperties: bias-disable: true + input-enable: true + output-high: true output-low: true @@ -133,6 +136,23 @@ examples: interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>; interrupt-controller; vdd-supply = <&p3v3>; - gpio-reserved-ranges = <5 1>; + gpio-reserved-ranges = <1 2>, <6 1>, <10 1>, <15 1>; + + pinctrl-0 = <&U62160_pins>, <&U62160_ipins>; + pinctrl-names = "default"; + + U62160_pins: cfg-pins { + pins = "gp03", "gp16", "gp20", "gp50", "gp51"; + function = "gpio"; + input-enable; + bias-pull-up; + }; + + U62160_ipins: icfg-pins { + pins = "gp04", "gp17", "gp21", "gp52", "gp53"; + function = "gpio"; + input-enable; + bias-pull-up; + }; }; }; diff --git a/Documentation/devicetree/bindings/pinctrl/mobileye,eyeq5-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/mobileye,eyeq5-pinctrl.yaml new file mode 100644 index 000000000000..5f00604bf48c --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/mobileye,eyeq5-pinctrl.yaml @@ -0,0 +1,242 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/mobileye,eyeq5-pinctrl.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Mobileye EyeQ5 pin controller + +description: > + The EyeQ5 pin controller handles the two pin banks of the system. It belongs + to a system-controller block called OLB. + + Pin control is about bias (pull-down, pull-up), drive strength and muxing. Pin + muxing supports two functions for each pin: first is GPIO, second is + pin-dependent. + + Pins and groups are bijective. + +maintainers: + - Grégory Clement <gregory.clement@bootlin.com> + - Théo Lebrun <theo.lebrun@bootlin.com> + - Vladimir Kondratiev <vladimir.kondratiev@mobileye.com> + +$ref: pinctrl.yaml# + +properties: + compatible: + enum: + - mobileye,eyeq5-pinctrl + + reg: + maxItems: 1 + +patternProperties: + "-pins?$": + type: object + description: Pin muxing configuration. + $ref: pinmux-node.yaml# + additionalProperties: false + properties: + pins: true + function: + enum: [gpio, + # Bank A + timer0, timer1, timer2, timer5, uart0, uart1, can0, can1, spi0, + spi1, refclk0, + # Bank B + timer3, timer4, timer6, uart2, can2, spi2, spi3, mclk0] + bias-disable: true + bias-pull-down: true + bias-pull-up: true + drive-strength: true + required: + - pins + - function + allOf: + - if: + properties: + function: + const: gpio + then: + properties: + pins: + items: # PA0 - PA28, PB0 - PB22 + pattern: '^(P(A|B)1?[0-9]|PA2[0-8]|PB2[0-2])$' + - if: + properties: + function: + const: timer0 + then: + properties: + pins: + items: + enum: [PA0, PA1] + - if: + properties: + function: + const: timer1 + then: + properties: + pins: + items: + enum: [PA2, PA3] + - if: + properties: + function: + const: timer2 + then: + properties: + pins: + items: + enum: [PA4, PA5] + - if: + properties: + function: + const: timer5 + then: + properties: + pins: + items: + enum: [PA6, PA7, PA8, PA9] + - if: + properties: + function: + const: uart0 + then: + properties: + pins: + items: + enum: [PA10, PA11] + - if: + properties: + function: + const: uart1 + then: + properties: + pins: + items: + enum: [PA12, PA13] + - if: + properties: + function: + const: can0 + then: + properties: + pins: + items: + enum: [PA14, PA15] + - if: + properties: + function: + const: can1 + then: + properties: + pins: + items: + enum: [PA16, PA17] + - if: + properties: + function: + const: spi0 + then: + properties: + pins: + items: + enum: [PA18, PA19, PA20, PA21, PA22] + - if: + properties: + function: + const: spi1 + then: + properties: + pins: + items: + enum: [PA23, PA24, PA25, PA26, PA27] + - if: + properties: + function: + const: refclk0 + then: + properties: + pins: + items: + enum: [PA28] + - if: + properties: + function: + const: timer3 + then: + properties: + pins: + items: + enum: [PB0, PB1] + - if: + properties: + function: + const: timer4 + then: + properties: + pins: + items: + enum: [PB2, PB3] + - if: |