| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management updates from Rafael Wysocki:
"These are mostly fixes on top of the previously merged power
management material with the addition of some teo cpuidle governor
updates, some of which may also be regarded as fixes:
- Add missing error handling for syscore_suspend() to the hibernation
core code (Wentao Liang)
- Revert a commit that added unused macros (Andy Shevchenko)
- Synchronize the runtime PM status of devices that were runtime-
suspended before a system-wide suspend and need to be resumed
during the subsequent system-wide resume transition (Rafael
Wysocki)
- Clean up the teo cpuidle governor and make the handling of short
idle intervals in it consistent regardless of the properties of
idle states supplied by the cpuidle driver (Rafael Wysocki)
- Fix some boost-related issues in cpufreq (Lifeng Zheng)
- Fix build issues in the s3c64xx and airoha cpufreq drivers (Viresh
Kumar)
- Remove unconditional binding of schedutil governor kthreads to the
affected CPUs if the cpufreq driver indicates that updates can
happen from any CPU (Christian Loehle)"
* tag 'pm-6.14-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM: sleep: core: Synchronize runtime PM status of parents and children
cpufreq: airoha: Depends on OF
PM: Revert "Add EXPORT macros for exporting PM functions"
PM: hibernate: Add error handling for syscore_suspend()
cpufreq/schedutil: Only bind threads if needed
cpufreq: ACPI: Remove set_boost in acpi_cpufreq_cpu_init()
cpufreq: CPPC: Fix wrong max_freq in policy initialization
cpufreq: Introduce a more generic way to set default per-policy boost flag
cpufreq: Fix re-boost issue after hotplugging a CPU
cpufreq: s3c64xx: Fix compilation warning
cpuidle: teo: Skip sleep length computation for low latency constraints
cpuidle: teo: Replace time_span_ns with a flag
cpuidle: teo: Simplify handling of total events count
cpuidle: teo: Skip getting the sleep length if wakeups are very frequent
cpuidle: teo: Simplify counting events used for tick management
cpuidle: teo: Clarify two code comments
cpuidle: teo: Drop local variable prev_intercept_idx
cpuidle: teo: Combine candidate state index checks against 0
cpuidle: teo: Reorder candidate state index checks
cpuidle: teo: Rearrange idle state lookup code
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull MM updates from Andrew Morton:
"The various patchsets are summarized below. Plus of course many
indivudual patches which are described in their changelogs.
- "Allocate and free frozen pages" from Matthew Wilcox reorganizes
the page allocator so we end up with the ability to allocate and
free zero-refcount pages. So that callers (ie, slab) can avoid a
refcount inc & dec
- "Support large folios for tmpfs" from Baolin Wang teaches tmpfs to
use large folios other than PMD-sized ones
- "Fix mm/rodata_test" from Petr Tesarik performs some maintenance
and fixes for this small built-in kernel selftest
- "mas_anode_descend() related cleanup" from Wei Yang tidies up part
of the mapletree code
- "mm: fix format issues and param types" from Keren Sun implements a
few minor code cleanups
- "simplify split calculation" from Wei Yang provides a few fixes and
a test for the mapletree code
- "mm/vma: make more mmap logic userland testable" from Lorenzo
Stoakes continues the work of moving vma-related code into the
(relatively) new mm/vma.c
- "mm/page_alloc: gfp flags cleanups for alloc_contig_*()" from David
Hildenbrand cleans up and rationalizes handling of gfp flags in the
page allocator
- "readahead: Reintroduce fix for improper RA window sizing" from Jan
Kara is a second attempt at fixing a readahead window sizing issue.
It should reduce the amount of unnecessary reading
- "synchronously scan and reclaim empty user PTE pages" from Qi Zheng
addresses an issue where "huge" amounts of pte pagetables are
accumulated:
https://lore.kernel.org/lkml/cover.1718267194.git.zhengqi.arch@bytedance.com/
Qi's series addresses this windup by synchronously freeing PTE
memory within the context of madvise(MADV_DONTNEED)
- "selftest/mm: Remove warnings found by adding compiler flags" from
Muhammad Usama Anjum fixes some build warnings in the selftests
code when optional compiler warnings are enabled
- "mm: don't use __GFP_HARDWALL when migrating remote pages" from
David Hildenbrand tightens the allocator's observance of
__GFP_HARDWALL
- "pkeys kselftests improvements" from Kevin Brodsky implements
various fixes and cleanups in the MM selftests code, mainly
pertaining to the pkeys tests
- "mm/damon: add sample modules" from SeongJae Park enhances DAMON to
estimate application working set size
- "memcg/hugetlb: Rework memcg hugetlb charging" from Joshua Hahn
provides some cleanups to memcg's hugetlb charging logic
- "mm/swap_cgroup: remove global swap cgroup lock" from Kairui Song
removes the global swap cgroup lock. A speedup of 10% for a
tmpfs-based kernel build was demonstrated
- "zram: split page type read/write handling" from Sergey Senozhatsky
has several fixes and cleaups for zram in the area of
zram_write_page(). A watchdog softlockup warning was eliminated
- "move pagetable_*_dtor() to __tlb_remove_table()" from Kevin
Brodsky cleans up the pagetable destructor implementations. A rare
use-after-free race is fixed
- "mm/debug: introduce and use VM_WARN_ON_VMG()" from Lorenzo Stoakes
simplifies and cleans up the debugging code in the VMA merging
logic
- "Account page tables at all levels" from Kevin Brodsky cleans up
and regularizes the pagetable ctor/dtor handling. This results in
improvements in accounting accuracy
- "mm/damon: replace most damon_callback usages in sysfs with new
core functions" from SeongJae Park cleans up and generalizes
DAMON's sysfs file interface logic
- "mm/damon: enable page level properties based monitoring" from
SeongJae Park increases the amount of information which is
presented in response to DAMOS actions
- "mm/damon: remove DAMON debugfs interface" from SeongJae Park
removes DAMON's long-deprecated debugfs interfaces. Thus the
migration to sysfs is completed
- "mm/hugetlb: Refactor hugetlb allocation resv accounting" from
Peter Xu cleans up and generalizes the hugetlb reservation
accounting
- "mm: alloc_pages_bulk: small API refactor" from Luiz Capitulino
removes a never-used feature of the alloc_pages_bulk() interface
- "mm/damon: extend DAMOS filters for inclusion" from SeongJae Park
extends DAMOS filters to support not only exclusion (rejecting),
but also inclusion (allowing) behavior
- "Add zpdesc memory descriptor for zswap.zpool" from Alex Shi
introduces a new memory descriptor for zswap.zpool that currently
overlaps with struct page for now. This is part of the effort to
reduce the size of struct page and to enable dynamic allocation of
memory descriptors
- "mm, swap: rework of swap allocator locks" from Kairui Song redoes
and simplifies the swap allocator locking. A speedup of 400% was
demonstrated for one workload. As was a 35% reduction for kernel
build time with swap-on-zram
- "mm: update mips to use do_mmap(), make mmap_region() internal"
from Lorenzo Stoakes reworks MIPS's use of mmap_region() so that
mmap_region() can be made MM-internal
- "mm/mglru: performance optimizations" from Yu Zhao fixes a few
MGLRU regressions and otherwise improves MGLRU performance
- "Docs/mm/damon: add tuning guide and misc updates" from SeongJae
Park updates DAMON documentation
- "Cleanup for memfd_create()" from Isaac Manjarres does that thing
- "mm: hugetlb+THP folio and migration cleanups" from David
Hildenbrand provides various cleanups in the areas of hugetlb
folios, THP folios and migration
- "Uncached buffered IO" from Jens Axboe implements the new
RWF_DONTCACHE flag which provides synchronous dropbehind for
pagecache reading and writing. To permite userspace to address
issues with massive buildup of useless pagecache when
reading/writing fast devices
- "selftests/mm: virtual_address_range: Reduce memory" from Thomas
Weißschuh fixes and optimizes some of the MM selftests"
* tag 'mm-stable-2025-01-26-14-59' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (321 commits)
mm/compaction: fix UBSAN shift-out-of-bounds warning
s390/mm: add missing ctor/dtor on page table upgrade
kasan: sw_tags: use str_on_off() helper in kasan_init_sw_tags()
tools: add VM_WARN_ON_VMG definition
mm/damon/core: use str_high_low() helper in damos_wmark_wait_us()
seqlock: add missing parameter documentation for raw_seqcount_try_begin()
mm/page-writeback: consolidate wb_thresh bumping logic into __wb_calc_thresh
mm/page_alloc: remove the incorrect and misleading comment
zram: remove zcomp_stream_put() from write_incompressible_page()
mm: separate move/undo parts from migrate_pages_batch()
mm/kfence: use str_write_read() helper in get_access_type()
selftests/mm/mkdirty: fix memory leak in test_uffdio_copy()
kasan: hw_tags: Use str_on_off() helper in kasan_init_hw_tags()
selftests/mm: virtual_address_range: avoid reading from VM_IO mappings
selftests/mm: vm_util: split up /proc/self/smaps parsing
selftests/mm: virtual_address_range: unmap chunks after validation
selftests/mm: virtual_address_range: mmap() without PROT_WRITE
selftests/memfd/memfd_test: fix possible NULL pointer dereference
mm: add FGP_DONTCACHE folio creation flag
mm: call filemap_fdatawrite_range_kick() after IOCB_DONTCACHE issue
...
|
|
Before SLUB initialization, various subsystems used memblock_alloc to
allocate memory. In most cases, when memory allocation fails, an
immediate panic is required. To simplify this behavior and reduce
repetitive checks, introduce `memblock_alloc_or_panic`. This function
ensures that memory allocation failures result in a panic automatically,
improving code readability and consistency across subsystems that require
this behavior.
[guoweikang.kernel@gmail.com: arch/s390: save_area_alloc default failure behavior changed to panic]
Link: https://lkml.kernel.org/r/20250109033136.2845676-1-guoweikang.kernel@gmail.com
Link: https://lore.kernel.org/lkml/Z2fknmnNtiZbCc7x@kernel.org/
Link: https://lkml.kernel.org/r/20250102072528.650926-1-guoweikang.kernel@gmail.com
Signed-off-by: Guo Weikang <guoweikang.kernel@gmail.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> [m68k]
Reviewed-by: Alexander Gordeev <agordeev@linux.ibm.com> [s390]
Acked-by: Mike Rapoport (Microsoft) <rppt@kernel.org>
Cc: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
In hibernation_platform_enter(), the code did not check the
return value of syscore_suspend(), potentially leading to a
situation where syscore_resume() would be called even if
syscore_suspend() failed. This could cause unpredictable
behavior or system instability.
Modify the code sequence in question to properly handle errors returned
by syscore_suspend(). If an error occurs in the suspend path, the code
now jumps to label 'Enable_irqs' skipping the syscore_resume() call and
only enabling interrupts after setting the system state to SYSTEM_RUNNING.
Fixes: 40dc166cb5dd ("PM / Core: Introduce struct syscore_ops for core subsystems PM")
Signed-off-by: Wentao Liang <vulab@iscas.ac.cn>
Link: https://patch.msgid.link/20250119143205.2103-1-vulab@iscas.ac.cn
[ rjw: Changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Merge updates related to system sleep, a cpuidle update and an Energy
Model handling code update for 6.14-rc1:
- Allow configuring the system suspend-resume (DPM) watchdog to warn
earlier than panic (Douglas Anderson).
- Implement devm_device_init_wakeup() helper and introduce a device-
managed variant of dev_pm_set_wake_irq() (Joe Hattori, Peng Fan).
- Remove direct inclusions of 'pm_wakeup.h' which should be only
included via 'device.h' (Wolfram Sang).
- Clean up two comments in the core system-wide PM code (Rafael
Wysocki, Randy Dunlap).
- Add Clearwater Forest processor support to the intel_idle cpuidle
driver (Artem Bityutskiy).
- Move sched domains rebuild function from the schedutil cpufreq
governor to the Energy Model handling code (Rafael Wysocki).
* pm-sleep:
PM: sleep: wakeirq: Introduce device-managed variant of dev_pm_set_wake_irq()
PM: sleep: Allow configuring the DPM watchdog to warn earlier than panic
PM: sleep: convert comment from kernel-doc to plain comment
PM: wakeup: implement devm_device_init_wakeup() helper
PM: sleep: sysfs: don't include 'pm_wakeup.h' directly
PM: sleep: autosleep: don't include 'pm_wakeup.h' directly
PM: sleep: Update stale comment in device_resume()
* pm-cpuidle:
intel_idle: add Clearwater Forest SoC support
* pm-em:
PM: EM: Move sched domains rebuild function from schedutil to EM
|
|
Allow configuring the DPM watchdog to warn about slow suspend/resume
functions without causing a system panic(). This allows you to set the
DPM_WATCHDOG_WARNING_TIMEOUT to something like 5 or 10 seconds to get
warnings about slow suspend/resume functions that eventually succeed.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Link: https://patch.msgid.link/20250109125957.v2.1.I4554f931b8da97948f308ecc651b124338ee9603@changeid
[ rjw: Subject edit ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Modify a non-kernel-doc comment to begin with /* instead of /**
so that it does not cause a kernel-doc warning.
power.h:114: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Auxiliary structure used for reading the snapshot image data and
power.h:114: warning: missing initial short description on line:
* Auxiliary structure used for reading the snapshot image data and
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Link: https://patch.msgid.link/20250111063107.910825-1-rdunlap@infradead.org
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Function sugov_eas_rebuild_sd() defined in the schedutil cpufreq governor
implements generic functionality that may be useful in other places. In
particular, there is a plan to use it in the intel_pstate driver in the
future.
For this reason, move it from schedutil to the energy model code and
rename it to em_rebuild_sched_domains().
This also helps to get rid of some #ifdeffery in schedutil which is a
plus.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Christian Loehle <christian.loehle@arm.com>
|
|
The header clearly states that it does not want to be included directly,
only via 'device.h'. 'platform_device.h' works equally well. Remove the
direct inclusion.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://patch.msgid.link/20241118072917.3853-16-wsa+renesas@sang-engineering.com
[ rjw: Subject edit ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Pull kvm updates from Paolo Bonzini:
"The biggest change here is eliminating the awful idea that KVM had of
essentially guessing which pfns are refcounted pages.
The reason to do so was that KVM needs to map both non-refcounted
pages (for example BARs of VFIO devices) and VM_PFNMAP/VM_MIXMEDMAP
VMAs that contain refcounted pages.
However, the result was security issues in the past, and more recently
the inability to map VM_IO and VM_PFNMAP memory that _is_ backed by
struct page but is not refcounted. In particular this broke virtio-gpu
blob resources (which directly map host graphics buffers into the
guest as "vram" for the virtio-gpu device) with the amdgpu driver,
because amdgpu allocates non-compound higher order pages and the tail
pages could not be mapped into KVM.
This requires adjusting all uses of struct page in the
per-architecture code, to always work on the pfn whenever possible.
The large series that did this, from David Stevens and Sean
Christopherson, also cleaned up substantially the set of functions
that provided arch code with the pfn for a host virtual addresses.
The previous maze of twisty little passages, all different, is
replaced by five functions (__gfn_to_page, __kvm_faultin_pfn, the
non-__ versions of these two, and kvm_prefetch_pages) saving almost
200 lines of code.
ARM:
- Support for stage-1 permission indirection (FEAT_S1PIE) and
permission overlays (FEAT_S1POE), including nested virt + the
emulated page table walker
- Introduce PSCI SYSTEM_OFF2 support to KVM + client driver. This
call was introduced in PSCIv1.3 as a mechanism to request
hibernation, similar to the S4 state in ACPI
- Explicitly trap + hide FEAT_MPAM (QoS controls) from KVM guests. As
part of it, introduce trivial initialization of the host's MPAM
context so KVM can use the corresponding traps
- PMU support under nested virtualization, honoring the guest
hypervisor's trap configuration and event filtering when running a
nested guest
- Fixes to vgic ITS serialization where stale device/interrupt table
entries are not zeroed when the mapping is invalidated by the VM
- Avoid emulated MMIO completion if userspace has requested
synchronous external abort injection
- Various fixes and cleanups affecting pKVM, vCPU initialization, and
selftests
LoongArch:
- Add iocsr and mmio bus simulation in kernel.
- Add in-kernel interrupt controller emulation.
- Add support for virtualization extensions to the eiointc irqchip.
PPC:
- Drop lingering and utterly obsolete references to PPC970 KVM, which
was removed 10 years ago.
- Fix incorrect documentation references to non-existing ioctls
RISC-V:
- Accelerate KVM RISC-V when running as a guest
- Perf support to collect KVM guest statistics from host side
s390:
- New selftests: more ucontrol selftests and CPU model sanity checks
- Support for the gen17 CPU model
- List registers supported by KVM_GET/SET_ONE_REG in the
documentation
x86:
- Cleanup KVM's handling of Accessed and Dirty bits to dedup code,
improve documentation, harden against unexpected changes.
Even if the hardware A/D tracking is disabled, it is possible to
use the hardware-defined A/D bits to track if a PFN is Accessed
and/or Dirty, and that removes a lot of special cases.
- Elide TLB flushes when aging secondary PTEs, as has been done in
x86's primary MMU for over 10 years.
- Recover huge pages in-place in the TDP MMU when dirty page logging
is toggled off, instead of zapping them and waiting until the page
is re-accessed to create a huge mapping. This reduces vCPU jitter.
- Batch TLB flushes when dirty page logging is toggled off. This
reduces the time it takes to disable dirty logging by ~3x.
- Remove the shrinker that was (poorly) attempting to reclaim shadow
page tables in low-memory situations.
- Clean up and optimize KVM's handling of writes to
MSR_IA32_APICBASE.
- Advertise CPUIDs for new instructions in Clearwater Forest
- Quirk KVM's misguided behavior of initialized certain feature MSRs
to their maximum supported feature set, which can result in KVM
creating invalid vCPU state. E.g. initializing PERF_CAPABILITIES to
a non-zero value results in the vCPU having invalid state if
userspace hides PDCM from the guest, which in turn can lead to
save/restore failures.
- Fix KVM's handling of non-canonical checks for vCPUs that support
LA57 to better follow the "architecture", in quotes because the
actual behavior is poorly documented. E.g. most MSR writes and
descriptor table loads ignore CR4.LA57 and operate purely on
whether the CPU supports LA57.
- Bypass the register cache when querying CPL from kvm_sched_out(),
as filling the cache from IRQ context is generally unsafe; harden
the cache accessors to try to prevent similar issues from occuring
in the future. The issue that triggered this change was already
fixed in 6.12, but was still kinda latent.
- Advertise AMD_IBPB_RET to userspace, and fix a related bug where
KVM over-advertises SPEC_CTRL when trying to support cross-vendor
VMs.
- Minor cleanups
- Switch hugepage recovery thread to use vhost_task.
These kthreads can consume significant amounts of CPU time on
behalf of a VM or in response to how the VM behaves (for example
how it accesses its memory); therefore KVM tried to place the
thread in the VM's cgroups and charge the CPU time consumed by that
work to the VM's container.
However the kthreads did not process SIGSTOP/SIGCONT, and therefore
cgroups which had KVM instances inside could not complete freezing.
Fix this by replacing the kthread with a PF_USER_WORKER thread, via
the vhost_task abstraction. Another 100+ lines removed, with
generally better behavior too like having these threads properly
parented in the process tree.
- Revert a workaround for an old CPU erratum (Nehalem/Westmere) that
didn't really work; there was really nothing to work around anyway:
the broken patch was meant to fix nested virtualization, but the
PERF_GLOBAL_CTRL MSR is virtualized and therefore unaffected by the
erratum.
- Fix 6.12 regression where CONFIG_KVM will be built as a module even
if asked to be builtin, as long as neither KVM_INTEL nor KVM_AMD is
'y'.
x86 selftests:
- x86 selftests can now use AVX.
Documentation:
- Use rST internal links
- Reorganize the introduction to the API document
Generic:
- Protect vcpu->pid accesses outside of vcpu->mutex with a rwlock
instead of RCU, so that running a vCPU on a different task doesn't
encounter long due to having to wait for all CPUs become quiescent.
In general both reads and writes are rare, but userspace that
supports confidential computing is introducing the use of "helper"
vCPUs that may jump from one host processor to another. Those will
be very happy to trigger a synchronize_rcu(), and the effect on
performance is quite the disaster"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (298 commits)
KVM: x86: Break CONFIG_KVM_X86's direct dependency on KVM_INTEL || KVM_AMD
KVM: x86: add back X86_LOCAL_APIC dependency
Revert "KVM: VMX: Move LOAD_IA32_PERF_GLOBAL_CTRL errata handling out of setup_vmcs_config()"
KVM: x86: switch hugepage recovery thread to vhost_task
KVM: x86: expose MSR_PLATFORM_INFO as a feature MSR
x86: KVM: Advertise CPUIDs for new instructions in Clearwater Forest
Documentation: KVM: fix malformed table
irqchip/loongson-eiointc: Add virt extension support
LoongArch: KVM: Add irqfd support
LoongArch: KVM: Add PCHPIC user mode read and write functions
LoongArch: KVM: Add PCHPIC read and write functions
LoongArch: KVM: Add PCHPIC device support
LoongArch: KVM: Add EIOINTC user mode read and write functions
LoongArch: KVM: Add EIOINTC read and write functions
LoongArch: KVM: Add EIOINTC device support
LoongArch: KVM: Add IPI user mode read and write function
LoongArch: KVM: Add IPI read and write function
LoongArch: KVM: Add IPI device support
LoongArch: KVM: Add iocsr and mmio bus simulation in kernel
KVM: arm64: Pass on SVE mapping failures
...
|
|
On some devices there are HW dependencies for shared frequency and voltage
between devices. It will impact Energy Aware Scheduler (EAS) decision,
where CPUs share the voltage & frequency domain with other CPUs or devices
e.g.
- Mid CPUs + Big CPU
- Little CPU + L3 cache in DSU
- some other device + Little CPUs
Detailed explanation of one example:
When the L3 cache frequency is increased, the affected Little CPUs might
run at higher voltage and frequency. That higher voltage causes higher CPU
power and thus more energy is used for running the tasks. This is
important for background running tasks, which try to run on energy
efficient CPUs.
Therefore, add performance state limits which are applied for the device
(in this case CPU). This is important on SoCs with HW dependencies
mentioned above so that the Energy Aware Scheduler (EAS) does not use
performance states outside the valid min-max range for energy calculation.
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Link: https://patch.msgid.link/20241030164126.1263793-2-lukasz.luba@arm.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The PSCI v1.3 specification adds support for a SYSTEM_OFF2 function
which is analogous to ACPI S4 state. This will allow hosting
environments to determine that a guest is hibernated rather than just
powered off, and handle that state appropriately on subsequent launches.
Since commit 60c0d45a7f7a ("efi/arm64: use UEFI for system reset and
poweroff") the EFI shutdown method is deliberately preferred over PSCI
or other methods. So register a SYS_OFF_MODE_POWER_OFF handler which
*only* handles the hibernation, leaving the original PSCI SYSTEM_OFF as
a last resort via the legacy pm_power_off function pointer.
The hibernation code already exports a system_entering_hibernation()
function which is be used by the higher-priority handler to check for
hibernation. That existing function just returns the value of a static
boolean variable from hibernate.c, which was previously only set in the
hibernation_platform_enter() code path. Set the same flag in the simpler
code path around the call to kernel_power_off() too.
An alternative way to hook SYSTEM_OFF2 into the hibernation code would
be to register a platform_hibernation_ops structure with an ->enter()
method which makes the new SYSTEM_OFF2 call. But that would have the
unwanted side-effect of making hibernation take a completely different
code path in hibernation_platform_enter(), invoking a lot of special dpm
callbacks.
Another option might be to add a new SYS_OFF_MODE_HIBERNATE mode, with
fallback to SYS_OFF_MODE_POWER_OFF. Or to use the sys_off_data to
indicate whether the power off is for hibernation.
But this version works and is relatively simple.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20241019172459.2241939-7-dwmw2@infradead.org
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
|
|
no_llseek had been defined to NULL two years ago, in commit 868941b14441
("fs: remove no_llseek")
To quote that commit,
At -rc1 we'll need do a mechanical removal of no_llseek -
git grep -l -w no_llseek | grep -v porting.rst | while read i; do
sed -i '/\<no_llseek\>/d' $i
done
would do it.
Unfortunately, that hadn't been done. Linus, could you do that now, so
that we could finally put that thing to rest? All instances are of the
form
.llseek = no_llseek,
so it's obviously safe.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When saveable_highmem_page() is unused, it prevents kernel builds
with clang, `make W=1` and CONFIG_WERROR=y:
kernel/power/snapshot.c:1369:21: error: unused function 'saveable_highmem_page' [-Werror,-Wunused-function]
1369 | static inline void *saveable_highmem_page(struct zone *z, unsigned long p)
| ^~~~~~~~~~~~~~~~~~~~~
Fix this by removing unused stub.
See also commit 6863f5643dd7 ("kbuild: allow Clang to find unused static
inline functions for W=1 build").
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20240905184848.318978-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
As Documentation/filesystems/sysfs.rst suggested, show() should only use
sysfs_emit() or sysfs_emit_at() when formatting the value to be returned
to user space.
No functional change intended.
Signed-off-by: Xueqin Luo <luoxueqin@kylinos.cn>
Link: https://patch.msgid.link/20240801083156.2513508-3-luoxueqin@kylinos.cn
[ rjw: Subject edit ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
As Documentation/filesystems/sysfs.rst suggested, show() should only
use sysfs_emit() or sysfs_emit_at() when formatting the value to be
returned to user space.
No functional change intended.
Signed-off-by: Xueqin Luo <luoxueqin@kylinos.cn>
Link: https://patch.msgid.link/20240801083156.2513508-2-luoxueqin@kylinos.cn
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
To streamline maintenance efforts, we propose removing the implementation
of swap_free(). Instead, we can simply invoke swap_free_nr() with nr set
to 1. swap_free_nr() is designed with a bitmap consisting of only one
long, resulting in overhead that can be ignored for cases where nr equals
1.
A prime candidate for leveraging swap_free_nr() lies within
kernel/power/swap.c. Implementing this change facilitates the adoption of
batch processing for hibernation.
Link: https://lkml.kernel.org/r/20240529082824.150954-3-21cnbao@gmail.com
Signed-off-by: Barry Song <v-songbaohua@oppo.com>
Suggested-by: "Huang, Ying" <ying.huang@intel.com>
Reviewed-by: "Huang, Ying" <ying.huang@intel.com>
Acked-by: Chris Li <chrisl@kernel.org>
Reviewed-by: Ryan Roberts <ryan.roberts@arm.com>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Len Brown <len.brown@intel.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Andreas Larsson <andreas@gaisler.com>
Cc: Baolin Wang <baolin.wang@linux.alibaba.com>
Cc: Chuanhua Han <hanchuanhua@oppo.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Gao Xiang <xiang@kernel.org>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Kairui Song <kasong@tencent.com>
Cc: Khalid Aziz <khalid.aziz@oracle.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Suren Baghdasaryan <surenb@google.com>
Cc: Yosry Ahmed <yosryahmed@google.com>
Cc: Yu Zhao <yuzhao@google.com>
Cc: Zi Yan <ziy@nvidia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs
Pull vfs fixes from Christian Brauner:
- Fix io_uring based write-through after converting cifs to use the
netfs library
- Fix aio error handling when doing write-through via netfs library
- Fix performance regression in iomap when used with non-large folio
mappings
- Fix signalfd error code
- Remove obsolete comment in signalfd code
- Fix async request indication in netfs_perform_write() by raising
BDP_ASYNC when IOCB_NOWAIT is set
- Yield swap device immediately to prevent spurious EBUSY errors
- Don't cross a .backup mountpoint from backup volumes in afs to avoid
infinite loops
- Fix a race between umount and async request completion in 9p after 9p
was converted to use the netfs library
* tag 'vfs-6.10-rc2.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs:
netfs, 9p: Fix race between umount and async request completion
afs: Don't cross .backup mountpoint from backup volume
swap: yield device immediately
netfs: Fix setting of BDP_ASYNC from iocb flags
signalfd: drop an obsolete comment
signalfd: fix error return code
iomap: fault in smaller chunks for non-large folio mappings
filemap: add helper mapping_max_folio_size()
netfs: Fix AIO error handling when doing write-through
netfs: Fix io_uring based write-through
|
|
Otherwise we can cause spurious EBUSY issues when trying to mount the
rootfs later on.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=218845
Reported-by: Petri Kaukasoina <petri.kaukasoina@tuni.fi>
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs blocksize updates from Al Viro:
"This gets rid of bogus set_blocksize() uses, switches it over
to be based on a 'struct file *' and verifies that the caller
has the device opened exclusively"
* tag 'pull-set_blocksize' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
make set_blocksize() fail unless block device is opened exclusive
set_blocksize(): switch to passing struct file *
btrfs_get_bdev_and_sb(): call set_blocksize() only for exclusive opens
swsusp: don't bother with setting block size
zram: don't bother with reopening - just use O_EXCL for open
swapon(2): open swap with O_EXCL
swapon(2)/swapoff(2): don't bother with block size
pktcdvd: sort set_blocksize() calls out
bcache_register(): don't bother with set_blocksize()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup updates from Tejun Heo:
- The locking around cpuset hotplug processing has always been a bit of
mess which was worked around by making hotplug processing
asynchronous. The asynchronity isn't great and led to other issues.
We tried to make the behavior synchronous a while ago but that led to
lockdep splats. Waiman took another stab at cleaning up and making it
synchronous. The patch has been in -next for well over a month and
there haven't been any complaints, so fingers crossed.
- Tracepoints added to help understanding rstat lock contentions.
- A bunch of minor changes - doc updates, code cleanups and selftests.
* tag 'cgroup-for-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup: (24 commits)
cgroup/rstat: add cgroup_rstat_cpu_lock helpers and tracepoints
selftests/cgroup: Drop define _GNU_SOURCE
docs: cgroup-v1: Update page cache removal functions
selftests/cgroup: fix uninitialized variables in test_zswap.c
selftests/cgroup: cpu_hogger init: use {} instead of {NULL}
selftests/cgroup: fix clang warnings: uninitialized fd variable
selftests/cgroup: fix clang build failures for abs() calls
cgroup/cpuset: Remove outdated comment in sched_partition_write()
cgroup/cpuset: Fix incorrect top_cpuset flags
cgroup/cpuset: Avoid clearing CS_SCHED_LOAD_BALANCE twice
cgroup/cpuset: Statically initialize more members of top_cpuset
cgroup: Avoid unnecessary looping in cgroup_no_v1()
cgroup, legacy_freezer: update comment for freezer_css_offline()
docs, cgroup: add entries for pids to cgroup-v2.rst
cgroup: don't call cgroup1_pidlist_destroy_all() for v2
cgroup_freezer: update comment for freezer_css_online()
cgroup/rstat: desc member cgrp in cgroup_rstat_flush_release
cgroup/rstat: add cgroup_rstat_lock helpers and tracepoints
cgroup/pids: Remove superfluous zeroing
docs: cgroup-v1: Fix description for css_online
...
|
|
Merge Enery Model update and a power management documentation update for
6.10:
- Make the Samsung exynos-asv driver update the Energy Model after
adjusting voltage on top of some preliminary changes of the OPP and
Enery Model generic code (Lukasz Luba).
- Remove a reference to a function that has been dropped from the power
management documentation (Bjorn Helgaas).
* pm-em:
soc: samsung: exynos-asv: Update Energy Model after adjusting voltage
PM: EM: Add em_dev_update_chip_binning()
PM: EM: Refactor em_adjust_new_capacity()
OPP: OF: Export dev_opp_pm_calc_power() for usage from EM
* pm-docs:
Documentation: PM: Update platform_pci_wakeup_init() reference
|
|
same as with the swap...
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
strncpy() is deprecated for use on NUL-terminated destination strings
[1] and as such we should prefer more robust and less ambiguous string
interfaces.
This kernel config option is simply assigned with the resume_file
buffer. It should be NUL-terminated but not necessarily NUL-padded as
per its further usage with other string apis:
| static int __init find_resume_device(void)
| {
| if (!strlen(resume_file))
| return -ENOENT;
|
| pm_pr_dbg("Checking hibernation image partition %s\n", resume_file);
Use strscpy() [2] as it guarantees NUL-termination on the destination
buffer. Specifically, use the new 2-argument version of strscpy()
introduced in Commit e6584c3964f2f ("string: Allow 2-argument
strscpy()").
Link: https://www.kernel.org/doc/html/latest/process/deprecated.html#strncpy-on-nul-terminated-strings [1]
Link: https://manpages.debian.org/testing/linux-manual-4.8/strscpy.9.en.html [2]
Link: https://github.com/KSPP/linux/issues/90
Signed-off-by: Justin Stitt <justinstitt@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Since commit 3a5a6d0c2b03("cpuset: don't nest cgroup_mutex inside
get_online_cpus()"), cpuset hotplug was done asynchronously via a work
function. This is to avoid recursive locking of cgroup_mutex.
Since then, the cgroup locking scheme has changed quite a bit. A
cpuset_mutex was introduced to protect cpuset specific operations.
The cpuset_mutex is then replaced by a cpuset_rwsem. With commit
d74b27d63a8b ("cgroup/cpuset: Change cpuset_rwsem and hotplug lock
order"), cpu_hotplug_lock is acquired before cpuset_rwsem. Later on,
cpuset_rwsem is reverted back to cpuset_mutex. All these locking changes
allow the hotplug code to call into cpuset core directly.
The following commits were also merged due to the asynchronous nature
of cpuset hotplug processing.
- commit b22afcdf04c9 ("cpu/hotplug: Cure the cpusets trainwreck")
- commit 50e76632339d ("sched/cpuset/pm: Fix cpuset vs. suspend-resume
bugs")
- commit 28b89b9e6f7b ("cpuset: handle race between CPU hotplug and
cpuset_hotplug_work")
Clean up all these bandages by making cpuset hotplug
processing synchronous again with the exception that the call to
cgroup_transfer_tasks() to transfer tasks out of an empty cgroup v1
cpuset, if necessary, will still be done via a work function due to the
existing cgroup_mutex -> cpu_hotplug_lock dependency. It is possible
to reverse that dependency, but that will require updating a number of
different cgroup controllers. This special hotplug code path should be
rarely taken anyway.
As all the cpuset states will be updated by the end of the hotplug
operation, we can revert most the above commits except commit
50e76632339d ("sched/cpuset/pm: Fix cpuset vs. suspend-resume bugs")
which is partially reverted. Also removing some cpus_read_lock trylock
attempts in the cpuset partition code as they are no longer necessary
since the cpu_hotplug_lock is now held for the whole duration of the
cpuset hotplug code path.
Signed-off-by: Waiman Long <longman@redhat.com>
Tested-by: Valentin Schneider <vschneid@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Add a function which allows to modify easily the EM after the new voltage
information is available. The device drivers for the chip can adjust
the voltage values after setup. The voltage for the same frequency in OPP
can be different due to chip binning. The voltage impacts the power usage
and the EM power values can be updated to reflect that.
Reviewed-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Extract em_table_dup() and em_recalc_and_update() from
em_adjust_new_capacity(). Both functions will be later reused by the
'update EM due to chip binning' functionality.
Reviewed-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
s2idle works like a regular suspend with freezing processes and freezing
devices. All CPUs except the control CPU go into idle. Once this is
completed the control CPU kicks all other CPUs out of idle, so that they
reenter the idle loop and then enter s2idle state. The control CPU then
issues an swait() on the suspend state and therefore enters the idle loop
as well.
Due to being kicked out of idle, the other CPUs leave their NOHZ states,
which means the tick is active and the corresponding hrtimer is programmed
to the next jiffie.
On entering s2idle the CPUs shut down their local clockevent device to
prevent wakeups. The last CPU which enters s2idle shuts down its local
clockevent and freezes timekeeping.
On resume, one of the CPUs receives the wakeup interrupt, unfreezes
timekeeping and its local clockevent and starts the resume process. At that
point all other CPUs are still in s2idle with their clockevents switched
off. They only resume when they are kicked by another CPU or after resuming
devices and then receiving a device interrupt.
That means there is no guarantee that all CPUs will wakeup directly on
resume. As a consequence there is no guarantee that timers which are queued
on those CPUs and should expire directly after resume, are handled. Also
timer list timers which are remotely queued to one of those CPUs after
resume will not result in a reprogramming IPI as the tick is
active. Queueing a hrtimer will also not result in a reprogramming IPI
because the first hrtimer event is already in the past.
The recent introduction of the timer pull model (7ee988770326 ("timers:
Implement the hierarchical pull model")) amplifies this problem, if the
current migrator is one of the non woken up CPUs. When a non pinned timer
list timer is queued and the queuing CPU goes idle, it relies on the still
suspended migrator CPU to expire the timer which will happen by chance.
The problem exists since commit 8d89835b0467 ("PM: suspend: Do not pause
cpuidle in the suspend-to-idle path"). There the cpuidle_pause() call which
in turn invoked a wakeup for all idle CPUs was moved to a later point in
the resume process. This might not be reached or reached very late because
it waits on a timer of a still suspended CPU.
Address this by kicking all CPUs out of idle after the control CPU returns
from swait() so that they resume their timers and restore consistent system
state.
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218641
Fixes: 8d89835b0467 ("PM: suspend: Do not pause cpuidle in the suspend-to-idle path")
Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Mario Limonciello <mario.limonciello@amd.com>
Cc: 5.16+ <stable@kernel.org> # 5.16+
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"Subsytem:
- rtc_class is now const
Drivers:
- ds1511: cleanup, set date and time range and alarm offset limit
- max31335: fix interrupt handler
- pcf8523: improve suspend support"
* tag 'rtc-6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (28 commits)
MAINTAINER: Include linux-arm-msm for Qualcomm RTC patches
dt-bindings: rtc: zynqmp: Add support for Versal/Versal NET SoCs
rtc: class: make rtc_class constant
dt-bindings: rtc: abx80x: Improve checks on trickle charger constraints
MAINTAINERS: adjust file entry in ARM/Mediatek RTC DRIVER
rtc: nct3018y: fix possible NULL dereference
rtc: max31335: fix interrupt status reg
rtc: mt6397: select IRQ_DOMAIN instead of depending on it
dt-bindings: rtc: abx80x: convert to yaml
rtc: m41t80: Use the unified property API get the wakeup-source property
dt-bindings: at91rm9260-rtt: add sam9x7 compatible
dt-bindings: rtc: convert MT7622 RTC to the json-schema
dt-bindings: rtc: convert MT2717 RTC to the json-schema
rtc: pcf8523: add suspend handlers for alarm IRQ
rtc: ds1511: set alarm offset limit
rtc: ds1511: set range
rtc: ds1511: drop inline/noinline hints
rtc: ds1511: rename pdata
rtc: ds1511: implement ds1511_rtc_read_alarm properly
rtc: ds1511: remove partial alarm support
...
|
|
The EM only supports power in uW. Make sure that it is not possible to
register some downstream driver which doesn't provide power in uW.
The only exception is artificial EM, but that EM is ignored by the rest of
kernel frameworks (thermal, powercap, etc).
Reported-by: PoShao Chen <poshao.chen@mediatek.com>
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"From the functional perspective, the most significant change here is
the addition of support for Energy Models that can be updated
dynamically at run time.
There is also the addition of LZ4 compression support for hibernation,
the new preferred core support in amd-pstate, new platforms support in
the Intel RAPL driver, new model-specific EPP handling in intel_pstate
and more.
Apart from that, the cpufreq default transition delay is reduced from
10 ms to 2 ms (along with some related adjustments), the system
suspend statistics code undergoes a significant rework and there is a
usual bunch of fixes and code cleanups all over.
Specifics:
- Allow the Energy Model to be updated dynamically (Lukasz Luba)
- Add support for LZ4 compression algorithm to the hibernation image
creation and loading code (Nikhil V)
- Fix and clean up system suspend statistics collection (Rafael
Wysocki)
- Simplify device suspend and resume handling in the power management
core code (Rafael Wysocki)
- Fix PCI hibernation support description (Yiwei Lin)
- Make hibernation take set_memory_ro() return values into account as
appropriate (Christophe Leroy)
- Set mem_sleep_current during kernel command line setup to avoid an
ordering issue |
