| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Extend TCSR parsing to read optional dp_phy_mode_reg and add
qmp_usbc_set_phy_mode() to switch between USB and DP modes when
supported.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Xiangxu Yin <xiangxu.yin@oss.qualcomm.com>
Link: https://patch.msgid.link/20251215-add-displayport-support-for-qcs615-platform-v8-8-cbc72c88a44e@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The current implementation programs USB-specific registers in
qmp_usbc_com_init(), which is shared by both USB and DP modes. This
causes unnecessary configuration when the PHY is used for DP.
Move USB-only register setup from com_init to qmp_usbc_usb_power_on,
so it runs only for USB mode.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Xiangxu Yin <xiangxu.yin@oss.qualcomm.com>
Link: https://patch.msgid.link/20251215-add-displayport-support-for-qcs615-platform-v8-7-cbc72c88a44e@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
USB3DP PHY requires link and vco_div clocks when operating in DP mode.
Extend qmp_usbc_register_clocks and the clock provider logic to register
these clocks along with the existing pipe clock, to support both USB and
DP configurations.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Xiangxu Yin <xiangxu.yin@oss.qualcomm.com>
Link: https://patch.msgid.link/20251215-add-displayport-support-for-qcs615-platform-v8-6-cbc72c88a44e@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The original reset list only works for USB-only PHYs. USB3DP PHYs require
different reset names such as "dp_phy", so they need a separate list.
Moving reset configuration into qmp_phy_cfg allows per-PHY customization
without adding special-case logic in DT parsing. The legacy DT path keeps
using the old hardcoded list, while non-legacy paths use cfg->reset_list.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Xiangxu Yin <xiangxu.yin@oss.qualcomm.com>
Link: https://patch.msgid.link/20251215-add-displayport-support-for-qcs615-platform-v8-5-cbc72c88a44e@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
QMP USBC PHY drivers previously did not set init_load_uA for regulators,
which could result in incorrect vote levels. This patch introduces
regulator definitions with proper init_load_uA values based on each
chip's power grid design.
QCS615 USB3 PHY was previously reusing qcm2290_usb3phy_cfg, but its
regulator requirements differ. A new qcs615_usb3phy_cfg is added to
reflect the correct settings.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Xiangxu Yin <xiangxu.yin@oss.qualcomm.com>
Link: https://patch.msgid.link/20251215-add-displayport-support-for-qcs615-platform-v8-4-cbc72c88a44e@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Extend qmp_usbc_offsets and qmp_phy_cfg with DP-specific fields,
including register offsets, init tables, and callback hooks. Also
update qmp_usbc struct to track DP-related resources and state.
This enables support for USB/DP switchable Type-C PHYs that operate
in either mode.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Xiangxu Yin <xiangxu.yin@oss.qualcomm.com>
Link: https://patch.msgid.link/20251215-add-displayport-support-for-qcs615-platform-v8-3-cbc72c88a44e@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
To support following DisplayPort (DP) mode over the Type-C PHY, rename
USB-specific functions and ops to clearly separate them from common or
DP-related logic.
This is a preparatory cleanup to enable USB + DP dual mode.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Xiangxu Yin <xiangxu.yin@oss.qualcomm.com>
Link: https://patch.msgid.link/20251215-add-displayport-support-for-qcs615-platform-v8-2-cbc72c88a44e@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Set the regulator load before enabling the regulators to ensure stable
operation and proper power management on platforms where regulators are
shared between the QMP USB PHY and other IP blocks.
Introduce a regulator data structure with explicit enable load values and
use the regulator framework's `init_load_uA` field along with
`devm_regulator_bulk_get_const()` to ensure that `regulator_set_load()` is
applied automatically before the first enable, providing consistent power
management behavior across platforms.
Signed-off-by: Faisal Hassan <faisal.hassan@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://patch.msgid.link/20250905101243.14815-1-faisal.hassan@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Add QMP PCIe PHY support for the Kaanapali platform.
Signed-off-by: Jingyi Wang <jingyi.wang@oss.qualcomm.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Qiang Yu <qiang.yu@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://patch.msgid.link/20251124-kaanapali-pcie-phy-v4-5-d04ee9cca83b@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Some qserdes-com register offsets for the v8 PHY were previously omitted,
as they were not needed by earlier v8 PHY initialization sequences. Add
these missing v8 register offsets now required to support PCIe QMP PHY on
Kaanapali platform.
Signed-off-by: Jingyi Wang <jingyi.wang@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Qiang Yu <qiang.yu@oss.qualcomm.com>
Link: https://patch.msgid.link/20251124-kaanapali-pcie-phy-v4-4-d04ee9cca83b@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Kaanapali SoC uses QMP phy with version v8 for PCIe Gen3 x2. Add the new
PCS PCIE specific offsets in a dedicated header file.
Signed-off-by: Jingyi Wang <jingyi.wang@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Qiang Yu <qiang.yu@oss.qualcomm.com>
Link: https://patch.msgid.link/20251124-kaanapali-pcie-phy-v4-3-d04ee9cca83b@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Kaanapali SoC uses QMP PHY with version v8 for PCIe Gen3 x2, but requires
a completely unique qserdes-txrx register offsets compared to existing v8
offsets.
Hence, add a dedicated header file containing the FULL SET of qserdes-txrx
register definitions required for Kaanapali's PCIe PHY operation.
Signed-off-by: Jingyi Wang <jingyi.wang@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Qiang Yu <qiang.yu@oss.qualcomm.com>
Link: https://patch.msgid.link/20251124-kaanapali-pcie-phy-v4-2-d04ee9cca83b@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Enabling runtime PM before attaching the QPHY instance as driver data
can lead to a NULL pointer dereference in runtime PM callbacks that
expect valid driver data. There is a small window where the suspend
callback may run after PM runtime enabling and before runtime forbid.
This causes a sporadic crash during boot:
```
Unable to handle kernel NULL pointer dereference at virtual address 00000000000000a1
[...]
CPU: 0 UID: 0 PID: 11 Comm: kworker/0:1 Not tainted 6.16.7+ #116 PREEMPT
Workqueue: pm pm_runtime_work
pstate: 20000005 (nzCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : qusb2_phy_runtime_suspend+0x14/0x1e0 [phy_qcom_qusb2]
lr : pm_generic_runtime_suspend+0x2c/0x44
[...]
```
Attach the QPHY instance as driver data before enabling runtime PM to
prevent NULL pointer dereference in runtime PM callbacks.
Reorder pm_runtime_enable() and pm_runtime_forbid() to prevent a
short window where an unnecessary runtime suspend can occur.
Use the devres-managed version to ensure PM runtime is symmetrically
disabled during driver removal for proper cleanup.
Fixes: 891a96f65ac3 ("phy: qcom-qusb2: Add support for runtime PM")
Signed-off-by: Loic Poulain <loic.poulain@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Link: https://patch.msgid.link/20251219085640.114473-1-loic.poulain@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Add support for Gen5 x4 PCIe QMP PHY found on Glymur platform.
Signed-off-by: Prudhvi Yarlagadda <quic_pyarlaga@quicinc.com>
Signed-off-by: Wenbin Yao <wenbin.yao@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Acked-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Qiang Yu <qiang.yu@oss.qualcomm.com>
Link: https://patch.msgid.link/20251103-glymur-pcie-upstream-v6-3-18a5e0a538dc@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The new Glymur SoC bumps up the HW version of QMP phy to v8.50 for PCIE
g5x4. Add the new PCS offsets in a dedicated header file.
Signed-off-by: Prudhvi Yarlagadda <quic_pyarlaga@quicinc.com>
Signed-off-by: Wenbin Yao <wenbin.yao@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Qiang Yu <qiang.yu@oss.qualcomm.com>
Link: https://patch.msgid.link/20251103-glymur-pcie-upstream-v6-2-18a5e0a538dc@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Certain platforms may not have the PHY_ENABLE bit set on power on reset.
Update the current sequence to explicitly write to enable the PHY_ENABLE
bit. This ensures that regardless of the platform, the PHY is properly
enabled.
Signed-off-by: Ronak Raheja <ronak.raheja@oss.qualcomm.com>
Signed-off-by: Wesley Cheng <wesley.cheng@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patch.msgid.link/20250920032158.242725-1-wesley.cheng@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The QMP USB3/DP Combo PHY hosts an USB3 phy and a DP PHY on top
of a combo glue to route either lanes to the 4 shared physical lanes.
The routing of the lanes can be:
- 2 DP + 2 USB3
- 4 DP
- 2 USB3
Get the lanes mapping from DT and stop registering the USB-C
muxes in favor of a static mode and orientation detemined
by the lanes mapping.
This allows supporting boards with direct connection of USB3 and
DisplayPort lanes to the QMP Combo PHY lanes, not using the
USB-C Altmode feature.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Tested-by: Xilin Wu <sophon@radxa.com> # qcs6490-radxa-dragon-q6a
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patch.msgid.link/20251119-topic-x1e80100-hdmi-v7-2-2bee0e66cc1b@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
setup
Replace the custom qmp_regulator_data structure with the standard
regulator_bulk_data and use the init_load_uA field to set regulator
load during initialization.
This change simplifies the regulator setup by removing manual
allocation and load configuration logic, and leverages
devm_regulator_bulk_get_const() to automatically apply load settings
before enabling regulators.
Signed-off-by: Faisal Hassan <faisal.hassan@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Link: https://patch.msgid.link/20250922135901.2067-1-faisal.hassan@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy
Pull phy updates from Vinod Koul:
"The usual bunch of device support and update to drivers.
New Support
- Qualcomm SM8750 QMP PCIe PHY dual lane support, PMIV0104 eusb2
repeater support, QCS8300 eDP PHY support
- Renesas RZ/T2H and RZ/N2H support and updates to driver for that
- TI TCAN1051 phy support
- Rockchip rk3588 dphy support, RK3528 combphy support
Updates:
- cadence updates for calibration and polling for ready and enabling
of lower resolutions, runtime pm support,
- Rockchip: enable U3 otg port
- Renesas USXGMII mode support
- Qualcomm UFS PHY and PLL regulator load support"
* tag 'phy-for-6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (64 commits)
phy: rockchip: phy-rockchip-inno-csidphy: add support for rk3588 variant
phy: rockchip: phy-rockchip-inno-csidphy: allow for different reset lines
phy: rockchip: phy-rockchip-inno-csidphy: allow writes to grf register 0
dt-bindings: phy: rockchip-inno-csi-dphy: add rk3588 variant
dt-bindings: phy: rockchip-inno-csi-dphy: make power-domains non-required
phy: cadence: cdns-dphy: Enable lower resolutions in dphy
phy: renesas: r8a779f0-ether-serdes: add new step added to latest datasheet
phy: renesas: r8a779f0-ether-serdes: add USXGMII mode
phy: sophgo: Add USB 2.0 PHY driver for Sophgo CV18XX/SG200X
dt-bindings: phy: Add Sophgo CV1800 USB phy
phy: cadence: cdns-dphy: Update calibration wait time for startup state machine
phy: cadence: cdns-dphy: Fix PLL lock and O_CMN_READY polling
phy: renesas: rcar-gen3-usb2: Fix ID check logic with VBUS valid
dt-bindings: phy: ti,tcan104x-can: Document TI TCAN1051
phy: lynx-28g: check return value when calling lynx_28g_pll_get
phy: qcom: m31-eusb2: Fix the error log while enabling clock
phy: rockchip: usbdp: Remove redundant ternary operators
phy: renesas: rcar-gen3-usb2: Remove redundant ternary operators
phy: hisilicon: Remove redundant ternary operators
phy: qcom-qmp-ufs: Add PHY and PLL regulator load
...
|
|
Commit 0cc22f5a861c ("phy: qcom: qmp-pcie: Add PHY register retention
support") added support for using the "no_csr" reset to skip configuration
of the PHY if the init sequence was already applied by the boot firmware.
The expectation is that the PHY is only turned on/off by using the "no_csr"
reset, instead of powering it down and re-programming it after a full
reset.
The boot firmware on X1E does not fully conform to this expectation: If the
PCIe3 link fails to come up (e.g. because no PCIe card is inserted), the
firmware powers down the PHY using the QPHY_PCS_POWER_DOWN_CONTROL
register. The QPHY_START_CTRL register is kept as-is, so the driver assumes
the PHY is already initialized and skips the configuration/power up
sequence. The PHY won't come up again without clearing the
QPHY_PCS_POWER_DOWN_CONTROL, so eventually initialization fails:
qcom-qmp-pcie-phy 1be0000.phy: phy initialization timed-out
phy phy-1be0000.phy.0: phy poweron failed --> -110
qcom-pcie 1bd0000.pcie: cannot initialize host
qcom-pcie 1bd0000.pcie: probe with driver qcom-pcie failed with error -110
This can be reliably reproduced on the X1E CRD, QCP and Devkit when no card
is inserted for PCIe3.
Fix this by checking the QPHY_PCS_POWER_DOWN_CONTROL register in addition
to QPHY_START_CTRL. If the PHY is powered down with the register, it
doesn't conform to the expectations for using the "no_csr" reset, so we
fully re-initialize with the normal reset sequence.
Also check the register more carefully to ensure all of the bits we expect
are actually set. A simple !!(readl()) is not enough, because the PHY might
be only partially set up with some of the expected bits set.
Cc: stable@vger.kernel.org
Fixes: 0cc22f5a861c ("phy: qcom: qmp-pcie: Add PHY register retention support")
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250821-phy-qcom-qmp-pcie-nocsr-fix-v3-1-4898db0cc07c@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
While enabling clock, we incorrectly log 'ref clk' as 'cfg ahb clk'
Fix this since the devicetree bindings mentions it as ref clock.
Signed-off-by: Prashanth K <prashanth.k@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250826105254.3758803-1-prashanth.k@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Add phy and pll regulator load voting support for all supported
platforms by introducing dedicated regulator bulk data arrays
with their load values.
This ensures stable operation and proper power management for these
platforms where regulators are shared between the QMP UFS PHY and
other IP blocks by setting appropriate regulator load currents during
PHY operations.
Signed-off-by: Nitin Rawat <quic_nitirawa@quicinc.com>
Acked-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://lore.kernel.org/r/20250830070353.2694-3-nitin.rawat@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
On certain SoCs, power regulators are shared between the QMP UFS PHY
and other IP blocks. To ensure proper operation, the regulator
framework must be informed of the UFS PHY's load requirements.
This is essential because the regulator's operating mode—whether Low
Power or High Power—depends on the maximum expected load at any given
time, which the regulator driver needs to manage accordingly.
To support this, replace devm_regulator_bulk_get() with
devm_regulator_bulk_get_const() and inline the qmp_ufs_vreg_init()
function. additionally replace the array of regulator names with a
bulk regulator data structure, and utilize the init_load_uA field
provided by the regulator framework. This ensures that
regulator_set_load() is automatically invoked before the
first enable operation.
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Nitin Rawat <quic_nitirawa@quicinc.com>
Link: https://lore.kernel.org/r/20250830070353.2694-2-nitin.rawat@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Register a typec mux in order to change the PHY mode on the Type-C
mux events depending on the mode and the svid when in Altmode setup.
The DisplayPort phy should be left enabled if is still powered on
by the DRM DisplayPort controller, so bail out until the DisplayPort
PHY is not powered off.
The Type-C Mode/SVID only changes on plug/unplug, and USB SAFE states
will be set in between of USB-Only, Combo and DisplayPort Only so
this will leave enough time to the DRM DisplayPort controller to
turn of the DisplayPort PHY.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
[konrad: renaming, rewording, bug fixes]
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on Lenovo Thinkpad T14S
Link: https://lore.kernel.org/r/20250807-topic-4ln_dp_respin-v4-5-43272d6eca92@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Introduce an enum for the QMP Combo PHY modes, use it in the
QMP commmon phy init function and default to COMBO mode.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
[konrad: some renaming and rewording]
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on Lenovo Thinkpad T14S
Link: https://lore.kernel.org/r/20250807-topic-4ln_dp_respin-v4-4-43272d6eca92@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Switching the PHY Mode requires the DisplayPort PHY to be powered off,
keep track of the DisplayPort phy power state.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on Lenovo Thinkpad T14S
Link: https://lore.kernel.org/r/20250807-topic-4ln_dp_respin-v4-3-43272d6eca92@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
There are a numbers of ""modes"" involved: USB mode, Type-C mode (with
its altmodes), phy_mode and QMP_PHY mode (DP/combo/USB/off).
Rename the generic sounding 'mode' to 'phy_mode' to hopefully make
the code easier to follow.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on Lenovo Thinkpad T14S
Link: https://lore.kernel.org/r/20250807-topic-4ln_dp_respin-v4-2-43272d6eca92@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The PCIe Gen3 x2 PHY for SM8750 uses new phy, add the
required registers and offsets for this phy.
Signed-off-by: Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250809-pakala-v1-2-abf1c416dbaa@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Add support for the eUSB2 repeater found on the PMIV0104. There is no
default init table for this PMIC, just the board-specific tuning
parameters are used on top of the default tuning values.
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Link: https://lore.kernel.org/r/20250709-sm7635-eusb-repeater-v2-4-b6eff075c097@fairphone.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Support reading the FS Differential TX Output Resistance Tuning from
devicetree and writing the register, as required on some boards.
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Link: https://lore.kernel.org/r/20250709-sm7635-eusb-repeater-v2-2-b6eff075c097@fairphone.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The driver has never supported anything but OF probe so drop the unused
platform module alias.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250724154823.15998-6-johan@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
property "qcom,tune-usb2-preem" is for EUSB2_TUNE_USB2_PREEM
property "qcom,tune-usb2-amplitude" is for EUSB2_TUNE_IUSB2
The downstream correspondence is as follows:
EUSB2_TUNE_USB2_PREEM: Tx pre-emphasis tuning
EUSB2_TUNE_IUSB2: HS trasmit amplitude
EUSB2_TUNE_SQUELCH_U: Squelch detection threshold
EUSB2_TUNE_HSDISC: HS disconnect threshold
EUSB2_TUNE_EUSB_SLEW: slew rate
Fixes: 31bc94de7602 ("phy: qualcomm: phy-qcom-eusb2-repeater: Don't zero-out registers")
Signed-off-by: Pengyu Luo <mitltlatltl@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Luca Weiss <luca.weiss@fairphone.com>
Link: https://lore.kernel.org/r/20250812093957.32235-1-mitltlatltl@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The current configuration used for the IPQ5332 M31 USB PHY fails the
Near End High Speed Signal Quality compliance test. To resolve this,
update the initialization sequence as specified in the Hardware Design
Document.
Fixes: 08e49af50701 ("phy: qcom: Introduce M31 USB PHY driver")
Cc: stable@kernel.org
Signed-off-by: Kathiravan Thirumoorthy <kathiravan.thirumoorthy@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250630-ipq5332_hsphy_complaince-v2-1-63621439ebdb@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Add missing DP PHY status and VCO clock configuration registers to fix
configuring the VCO rate on SM8750. Without proper VCO rate setting, it
works on after-reset half of rate which is not enough for DP over USB to
work as seen on logs:
[drm:msm_dp_ctrl_link_train_1_2] *ERROR* max v_level reached
[drm:msm_dp_ctrl_link_train_1_2] *ERROR* link training #1 on phy 0 failed. ret=-11
Fixes: c4364048baf4 ("phy: qcom: qmp-combo: Add new PHY sequences for SM8750")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250616062541.7167-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Drivers should generally be quiet on successful probe so drop the
registration printk from the recently added M31 EUSB2 driver.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250617080401.11147-1-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The device_get_match_data() helper returns NULL if a new entry is ever
added without corresponding match data.
Fixes: 9c8504861cc4 ("phy: qcom: Add M31 based eUSB2 PHY driver")
Cc: Wesley Cheng <quic_wcheng@quicinc.com>
Cc: Melody Olvera <melody.olvera@oss.qualcomm.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250617080503.11262-1-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Update the PHY settings to align with the latest PCIe PHY
Hardware Programming Guide for both PCIe controllers on the
SA8775P platform.
Add the ln_shrd region for SA8775P, incorporating new register
writes as specified in the updated Hardware Programming Guide.
Update pcs table for QCS8300, since both QCS8300 and SA8775P are
closely related and share same pcs settings.
Signed-off-by: Mrinmay Sarkar <mrinmay.sarkar@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250617-update_phy-v5-1-2df83ed6a373@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Zeroing out registers does not happen in the downstream kernel, and will
"tune" the repeater in surely unexpected ways since most registers don't
have a reset value of 0x0.
Stop doing that and instead just set the registers that are in the init
sequence (though long term I don't think there's actually PMIC-specific
init sequences, there's board specific tuning, but that's a story for
another day).
Fixes: 99a517a582fc ("phy: qualcomm: phy-qcom-eusb2-repeater: Zero out untouched tuning regs")
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20250617-eusb2-repeater-tuning-v2-2-ed6c484f18ee@fairphone.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Add the <linux/bitfield.h> header to prevent a build error:
drivers/phy/qualcomm/phy-qcom-m31-eusb2.c: In function 'm31eusb2_phy_init':
drivers/phy/qualcomm/phy-qcom-m31-eusb2.c:210:37: error: implicit declaration of function 'FIELD_PREP' [-Wimplicit-function-declaration]
210 | FIELD_PREP(FSEL, data->fsel));
Fixes: 9c8504861cc4 ("phy: qcom: Add M31 based eUSB2 PHY driver")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Wesley Cheng <quic_wcheng@quicinc.com>
Cc: Melody Olvera <melody.olvera@oss.qualcomm.com>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: Kishon Vijay Abraham I <kishon@kernel.org>
Cc: linux-phy@lists.infradead.org
Cc: linux-arm-msm@vger.kernel.org
Link: https://lore.kernel.org/r/20250617034249.2067135-1-rdunlap@infradead.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Drivers should generally be quiet on successful probe, but this is not
followed by some PHY drivers, for example:
snps-eusb2-hsphy 88e1000.phy: Registered Snps-eUSB2 phy
qcom-eusb2-repeater c432000.spmi:pmic@7:phy@fd00: Registered Qcom-eUSB2 repeater
qcom-eusb2-repeater c432000.spmi:pmic@a:phy@fd00: Registered Qcom-eUSB2 repeater
qcom-eusb2-repeater c432000.spmi:pmic@b:phy@fd00: Registered Qcom-eUSB2 repeater
snps-eusb2-hsphy fd3000.phy: Registered Snps-eUSB2 phy
snps-eusb2-hsphy fd9000.phy: Registered Snps-eUSB2 phy
snps-eusb2-hsphy fde000.phy: Registered Snps-eUSB2 phy
snps-eusb2-hsphy 88e0000.phy: Registered Snps-eUSB2 phy
snps-eusb2-hsphy 88e2000.phy: Registered Snps-eUSB2 phy
Drop (or demote to debug level) unnecessary registration info messages
to make boot logs a little less noisy.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20250523085112.11287-1-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
SM8750 utilizes an eUSB2 PHY from M31. Add the initialization
sequences to bring it out of reset and into an operational state. This
differs to the M31 USB driver, in that the M31 eUSB2 driver will
require a connection to an eUSB2 repeater. This PHY driver will handle
the initialization of the associated eUSB2 repeater when required.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Signed-off-by: Melody Olvera <melody.olvera@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250527-sm8750_usb_master-v6-6-d58de3b41d34@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The eUSB2 repeater that exists in the QCOM PMICs are utilized for several
different eUSB2 PHY vendors, such as M31 or Synopsys. Hence, the wording
needs to be updated to remove associations to a specific vendor.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Signed-off-by: Melody Olvera <melody.olvera@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250527-sm8750_usb_master-v6-5-d58de3b41d34@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Add new register offsets and PHY values for SM8750. Some of the previous
definitions can be leveraged from older PHY versions as offsets within
registers have not changed. This also adds the required PHY sequence that
is recommended after running hardware characterization.
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Signed-off-by: Melody Olvera <melody.olvera@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20250527-sm8750_usb_master-v6-4-d58de3b41d34@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
In qmp_ufs_power_off, the PHY is already powered down by asserting
QPHY_PCS_POWER_DOWN_CONTROL. Therefore, additional phy_reset and
stopping SerDes are unnecessary. Also this approach does not
align with the phy HW programming guide.
Thus, refactor qmp_ufs_power_off to remove the phy_reset and stop
SerDes calls to simplify the code and ensure alignment with the PHY
HW programming guide.
Signed-off-by: Nitin Rawat <quic_nitirawa@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250526153821.7918-10-quic_nitirawa@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
qmp_ufs_exit() is a wrapper function. It only calls qmp_ufs_com_exit().
Remove it to simplify the ufs phy driver.
Additonally partial Inline(dropping the reset assert) qmp_ufs_com_exit
into qmp_ufs_power_off function to avoid unnecessary function call
and to align with the Phy programming guide.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Nitin Rawat <quic_nitirawa@quicinc.com>
Link: https://lore.kernel.org/r/20250526153821.7918-9-quic_nitirawa@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Rename qmp_ufs_disable to qmp_ufs_power_off to better represent its
functionality. Additionally, inline qmp_ufs_exit into qmp_ufs_power_off
function to preserve the functionality of .power_off.
There is no functional change.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Nitin Rawat <quic_nitirawa@quicinc.com>
Link: https://lore.kernel.org/r/20250526153821.7918-8-quic_nitirawa@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The qmp_ufs_power_on() function acts as a wrapper, solely invoking
qmp_ufs_com_init(). Additionally, the code within qmp_ufs_com_init()
does not correspond well with its name.
Therefore, to enhance the readability and eliminate unnecessary
function call inline qmp_ufs_com_init() into qmp_ufs_power_on().
There is no change to the functionality.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Nitin Rawat <quic_nitirawa@quicinc.com>
Link: https://lore.kernel.org/r/20250526153821.7918-7-quic_nitirawa@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Refactor the UFS PHY reset handling to parse the reset logic only once
during initialization, instead of every resume.
As part of this change, move the UFS PHY reset parsing logic from
qmp_phy_power_on to the new qmp_ufs_phy_init function introduced
as part of phy_ops::init callback.
Co-developed-by: Ram Kumar Dwivedi <quic_rdwivedi@quicinc.com>
Signed-off-by: Ram Kumar Dwivedi <quic_rdwivedi@quicinc.com>
Signed-off-by: Nitin Rawat <quic_nitirawa@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250526153821.7918-6-quic_nitirawa@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Commit 052553af6a31 ("ufs/phy: qcom: Refactor to use phy_init call")
puts enabling regulators & clks, calibrating UFS PHY, starting serdes
and polling PCS ready status into phy_power_on.
In Current code regulators enable, clks enable, calibrating UFS PHY,
start_serdes and polling PCS_ready_status are part of phy_power_on.
UFS PHY registers are retained after power collapse, meaning calibrating
UFS PHY, start_serdes and polling PCS_ready_status can be done only when
hba is powered_on, and not needed every time when phy_power_on is called
during resume. Hence keep the code which enables PHY's regulators & clks
in phy_power_on and move the rest steps into phy_calibrate function.
Refactor the code to retain PHY regulators & clks in phy_power_on and
move out rest of the code to new phy_calibrate function.
Also move reset_control_assert to qmp_ufs_phy_calibrate to align
with Hardware programming guide.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Co-developed-by: Can Guo <quic_cang@quicinc.com>
Signed-off-by: Can Guo <quic_cang@quicinc.com>
Signed-off-by: Nitin Rawat <quic_nitirawa@quicinc.com>
Link: https://lore.kernel.org/r/20250526153821.7918-5-quic_nitirawa@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Rename qmp_ufs_enable to qmp_ufs_power_on and qmp_ufs_power_on to
qmp_ufs_phy_calibrate to better reflect their functionality. Also
update function calls and structure assignments accordingly.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Co-developed-by: Ram Kumar Dwivedi <quic_rdwivedi@quicinc.com>
Signed-off-by: Ram Kumar Dwivedi <quic_rdwivedi@quicinc.com>
Signed-off-by: Nitin Rawat <quic_nitirawa@quicinc.com>
Link: https://lore.kernel.org/r/20250526153821.7918-4-quic_nitirawa@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
