Merge tag 'nand/for-4.13' into MTD

From Boris:
"""
This pull request contains the following core changes:

* addition of on-ecc support to Micron driver
* addition of helpers to help drivers choose most appropriate ECC
  settings
* deletion of dead-code (cached programming and ->errstat() hook)
* make sure drivers that do not support the SET/GET FEATURES command
  return ENOTSUPP use a dummy ->set/get_features implementation
  returning -ENOTSUPP (required for Micron on-die ECC)
* change the semantic of ecc->write_page() for drivers setting the
  NAND_ECC_CUSTOM_PAGE_ACCESS flag
* support exiting 'GET STATUS' command in default ->cmdfunc()
  implementations
* change the prototype of ->setup_data_interface()

A bunch of driver related changes:

* various cleanup, fixes and improvements of the MTK driver
* OMAP DT bindings fixes
* support for ->setup_data_interface() in the fsmc driver
* support for imx7 in the gpmi driver
* finalization of the denali driver rework (thanks to Masahiro for the
  work he's done on this driver)
* fix "bitflips in erased pages" handling in the ifc driver
* addition of PM ops and dynamic timing configuration to the atmel
  driver

And as usual we also have a few minor cleanup/fixes/improvements
patches across the subsystem.
"""

33 files changed, 2430 insertions, 1608 deletions

diff --git a/drivers/mtd/nand/Kconfig b/drivers/mtd/nand/Kconfig
index c3029528063b..dbfa72d61d5a 100644
--- a/drivers/mtd/nand/Kconfig
+++ b/drivers/mtd/nand/Kconfig
@@ -308,6 +308,7 @@ config MTD_NAND_CS553X
 config MTD_NAND_ATMEL
 	tristate "Support for NAND Flash / SmartMedia on AT91"
 	depends on ARCH_AT91
+	select MFD_ATMEL_SMC
 	help
 	  Enables support for NAND Flash / Smart Media Card interface
 	  on Atmel AT91 processors.
@@ -542,6 +543,7 @@ config MTD_NAND_SUNXI
 
 config MTD_NAND_HISI504
 	tristate "Support for NAND controller on Hisilicon SoC Hip04"
+	depends on ARCH_HISI || COMPILE_TEST
 	depends on HAS_DMA
 	help
 	  Enables support for NAND controller on Hisilicon SoC Hip04.
@@ -555,6 +557,7 @@ config MTD_NAND_QCOM
 
 config MTD_NAND_MTK
 	tristate "Support for NAND controller on MTK SoCs"
+	depends on ARCH_MEDIATEK || COMPILE_TEST
 	depends on HAS_DMA
 	help
 	  Enables support for NAND controller on MTK SoCs.
diff --git a/drivers/mtd/nand/atmel/nand-controller.c b/drivers/mtd/nand/atmel/nand-controller.c
index 3b2446896147..d922a88e407f 100644
--- a/drivers/mtd/nand/atmel/nand-controller.c
+++ b/drivers/mtd/nand/atmel/nand-controller.c
@@ -57,6 +57,7 @@
 #include <linux/interrupt.h>
 #include <linux/mfd/syscon.h>
 #include <linux/mfd/syscon/atmel-matrix.h>
+#include <linux/mfd/syscon/atmel-smc.h>
 #include <linux/module.h>
 #include <linux/mtd/nand.h>
 #include <linux/of_address.h>
@@ -64,7 +65,6 @@
 #include <linux/of_platform.h>
 #include <linux/iopoll.h>
 #include <linux/platform_device.h>
-#include <linux/platform_data/atmel.h>
 #include <linux/regmap.h>
 
 #include "pmecc.h"
@@ -151,6 +151,8 @@ struct atmel_nand_cs {
 		void __iomem *virt;
 		dma_addr_t dma;
 	} io;
+
+	struct atmel_smc_cs_conf smcconf;
 };
 
 struct atmel_nand {
@@ -196,6 +198,8 @@ struct atmel_nand_controller_ops {
 	void (*nand_init)(struct atmel_nand_controller *nc,
 			  struct atmel_nand *nand);
 	int (*ecc_init)(struct atmel_nand *nand);
+	int (*setup_data_interface)(struct atmel_nand *nand, int csline,
+				    const struct nand_data_interface *conf);
 };
 
 struct atmel_nand_controller_caps {
@@ -912,7 +916,7 @@ static int atmel_hsmc_nand_pmecc_write_pg(struct nand_chip *chip,
 	struct mtd_info *mtd = nand_to_mtd(chip);
 	struct atmel_nand *nand = to_atmel_nand(chip);
 	struct atmel_hsmc_nand_controller *nc;
-	int ret;
+	int ret, status;
 
 	nc = to_hsmc_nand_controller(chip->controller);
 
@@ -954,6 +958,10 @@ static int atmel_hsmc_nand_pmecc_write_pg(struct nand_chip *chip,
 		dev_err(nc->base.dev, "Failed to program NAND page (err = %d)\n",
 			ret);
 
+	status = chip->waitfunc(mtd, chip);
+	if (status & NAND_STATUS_FAIL)
+		return -EIO;
+
 	return ret;
 }
 
@@ -1175,6 +1183,295 @@ static int atmel_hsmc_nand_ecc_init(struct atmel_nand *nand)
 	return 0;
 }
 
+static int atmel_smc_nand_prepare_smcconf(struct atmel_nand *nand,
+					const struct nand_data_interface *conf,
+					struct atmel_smc_cs_conf *smcconf)
+{
+	u32 ncycles, totalcycles, timeps, mckperiodps;
+	struct atmel_nand_controller *nc;
+	int ret;
+
+	nc = to_nand_controller(nand->base.controller);
+
+	/* DDR interface not supported. */
+	if (conf->type != NAND_SDR_IFACE)
+		return -ENOTSUPP;
+
+	/*
+	 * tRC < 30ns implies EDO mode. This controller does not support this
+	 * mode.
+	 */
+	if (conf->timings.sdr.tRC_min < 30)
+		return -ENOTSUPP;
+
+	atmel_smc_cs_conf_init(smcconf);
+
+	mckperiodps = NSEC_PER_SEC / clk_get_rate(nc->mck);
+	mckperiodps *= 1000;
+
+	/*
+	 * Set write pulse timing. This one is easy to extract:
+	 *
+	 * NWE_PULSE = tWP
+	 */
+	ncycles = DIV_ROUND_UP(conf->timings.sdr.tWP_min, mckperiodps);
+	totalcycles = ncycles;
+	ret = atmel_smc_cs_conf_set_pulse(smcconf, ATMEL_SMC_NWE_SHIFT,
+					  ncycles);
+	if (ret)
+		return ret;
+
+	/*
+	 * The write setup timing depends on the operation done on the NAND.
+	 * All operations goes through the same data bus, but the operation
+	 * type depends on the address we are writing to (ALE/CLE address
+	 * lines).
+	 * Since we have no way to differentiate the different operations at
+	 * the SMC level, we must consider the worst case (the biggest setup
+	 * time among all operation types):
+	 *
+	 * NWE_SETUP = max(tCLS, tCS, tALS, tDS) - NWE_PULSE
+	 */
+	timeps = max3(conf->timings.sdr.tCLS_min, conf->timings.sdr.tCS_min,
+		      conf->timings.sdr.tALS_min);
+	timeps = max(timeps, conf->timings.sdr.tDS_min);
+	ncycles = DIV_ROUND_UP(timeps, mckperiodps);
+	ncycles = ncycles > totalcycles ? ncycles - totalcycles : 0;
+	totalcycles += ncycles;
+	ret = atmel_smc_cs_conf_set_setup(smcconf, ATMEL_SMC_NWE_SHIFT,
+					  ncycles);
+	if (ret)
+		return ret;
+
+	/*
+	 * As for the write setup timing, the write hold timing depends on the
+	 * operation done on the NAND:
+	 *
+	 * NWE_HOLD = max(tCLH, tCH, tALH, tDH, tWH)
+	 */
+	timeps = max3(conf->timings.sdr.tCLH_min, conf->timings.sdr.tCH_min,
+		      conf->timings.sdr.tALH_min);
+	timeps = max3(timeps, conf->timings.sdr.tDH_min,
+		      conf->timings.sdr.tWH_min);
+	ncycles = DIV_ROUND_UP(timeps, mckperiodps);
+	totalcycles += ncycles;
+
+	/*
+	 * The write cycle timing is directly matching tWC, but is also
+	 * dependent on the other timings on the setup and hold timings we
+	 * calculated earlier, which gives:
+	 *
+	 * NWE_CYCLE = max(tWC, NWE_SETUP + NWE_PULSE + NWE_HOLD)
+	 */
+	ncycles = DIV_ROUND_UP(conf->timings.sdr.tWC_min, mckperiodps);
+	ncycles = max(totalcycles, ncycles);
+	ret = atmel_smc_cs_conf_set_cycle(smcconf, ATMEL_SMC_NWE_SHIFT,
+					  ncycles);
+	if (ret)
+		return ret;
+
+	/*
+	 * We don't want the CS line to be toggled between each byte/word
+	 * transfer to the NAND. The only way to guarantee that is to have the
+	 * NCS_{WR,RD}_{SETUP,HOLD} timings set to 0, which in turn means:
+	 *
+	 * NCS_WR_PULSE = NWE_CYCLE
+	 */
+	ret = atmel_smc_cs_conf_set_pulse(smcconf, ATMEL_SMC_NCS_WR_SHIFT,
+					  ncycles);
+	if (ret)
+		return ret;
+
+	/*
+	 * As for the write setup timing, the read hold timing depends on the
+	 * operation done on the NAND:
+	 *
+	 * NRD_HOLD = max(tREH, tRHOH)
+	 */
+	timeps = max(conf->timings.sdr.tREH_min, conf->timings.sdr.tRHOH_min);
+	ncycles = DIV_ROUND_UP(timeps, mckperiodps);
+	totalcycles = ncycles;
+
+	/*
+	 * TDF = tRHZ - NRD_HOLD
+	 */
+	ncycles = DIV_ROUND_UP(conf->timings.sdr.tRHZ_max, mckperiodps);
+	ncycles -= totalcycles;
+
+	/*
+	 * In ONFI 4.0 specs, tRHZ has been increased to support EDO NANDs and
+	 * we might end up with a config that does not fit in the TDF field.
+	 * Just take the max value in this case and hope that the NAND is more
+	 * tolerant than advertised.
+	 */
+	if (ncycles > ATMEL_SMC_MODE_TDF_MAX)
+		ncycles = ATMEL_SMC_MODE_TDF_MAX;
+	else if (ncycles < ATMEL_SMC_MODE_TDF_MIN)
+		ncycles = ATMEL_SMC_MODE_TDF_MIN;
+
+	smcconf->mode |= ATMEL_SMC_MODE_TDF(ncycles) |
+			 ATMEL_SMC_MODE_TDFMODE_OPTIMIZED;
+
+	/*
+	 * Read pulse timing directly matches tRP:
+	 *
+	 * NRD_PULSE = tRP
+	 */
+	ncycles = DIV_ROUND_UP(conf->timings.sdr.tRP_min, mckperiodps);
+	totalcycles += ncycles;
+	ret = atmel_smc_cs_conf_set_pulse(smcconf, ATMEL_SMC_NRD_SHIFT,
+					  ncycles);
+	if (ret)
+		return ret;
+
+	/*
+	 * The write cycle timing is directly matching tWC, but is also
+	 * dependent on the setup and hold timings we calculated earlier,
+	 * which gives:
+	 *
+	 * NRD_CYCLE = max(tRC, NRD_PULSE + NRD_HOLD)
+	 *
+	 * NRD_SETUP is always 0.
+	 */
+	ncycles = DIV_ROUND_UP(conf->timings.sdr.tRC_min, mckperiodps);
+	ncycles = max(totalcycles, ncycles);
+	ret = atmel_smc_cs_conf_set_cycle(smcconf, ATMEL_SMC_NRD_SHIFT,
+					  ncycles);
+	if (ret)
+		return ret;
+
+	/*
+	 * We don't want the CS line to be toggled between each byte/word
+	 * transfer from the NAND. The only way to guarantee that is to have
+	 * the NCS_{WR,RD}_{SETUP,HOLD} timings set to 0, which in turn means:
+	 *
+	 * NCS_RD_PULSE = NRD_CYCLE
+	 */
+	ret = atmel_smc_cs_conf_set_pulse(smcconf, ATMEL_SMC_NCS_RD_SHIFT,
+					  ncycles);
+	if (ret)
+		return ret;
+
+	/* Txxx timings are directly matching tXXX ones. */
+	ncycles = DIV_ROUND_UP(conf->timings.sdr.tCLR_min, mckperiodps);
+	ret = atmel_smc_cs_conf_set_timing(smcconf,
+					   ATMEL_HSMC_TIMINGS_TCLR_SHIFT,
+					   ncycles);
+	if (ret)
+		return ret;
+
+	ncycles = DIV_ROUND_UP(conf->timings.sdr.tADL_min, mckperiodps);
+	ret = atmel_smc_cs_conf_set_timing(smcconf,
+					   ATMEL_HSMC_TIMINGS_TADL_SHIFT,
+					   ncycles);
+	if (ret)
+		return ret;
+
+	ncycles = DIV_ROUND_UP(conf->timings.sdr.tAR_min, mckperiodps);
+	ret = atmel_smc_cs_conf_set_timing(smcconf,
+					   ATMEL_HSMC_TIMINGS_TAR_SHIFT,
+					   ncycles);
+	if (ret)
+		return ret;
+
+	ncycles = DIV_ROUND_UP(conf->timings.sdr.tRR_min, mckperiodps);
+	ret = atmel_smc_cs_conf_set_timing(smcconf,
+					   ATMEL_HSMC_TIMINGS_TRR_SHIFT,
+					   ncycles);
+	if (ret)
+		return ret;
+
+	ncycles = DIV_ROUND_UP(conf->timings.sdr.tWB_max, mckperiodps);
+	ret = atmel_smc_cs_conf_set_timing(smcconf,
+					   ATMEL_HSMC_TIMINGS_TWB_SHIFT,
+					   ncycles);
+	if (ret)
+		return ret;
+
+	/* Attach the CS line to the NFC logic. */
+	smcconf->timings |= ATMEL_HSMC_TIMINGS_NFSEL;
+
+	/* Set the appropriate data bus width. */
+	if (nand->base.options & NAND_BUSWIDTH_16)
+		smcconf->mode |= ATMEL_SMC_MODE_DBW_16;
+
+	/* Operate in NRD/NWE READ/WRITEMODE. */
+	smcconf->mode |= ATMEL_SMC_MODE_READMODE_NRD |
+			 ATMEL_SMC_MODE_WRITEMODE_NWE;
+
+	return 0;
+}
+
+static int atmel_smc_nand_setup_data_interface(struct atmel_nand *nand,
+					int csline,
+					const struct nand_data_interface *conf)
+{
+	struct atmel_nand_controller *nc;
+	struct atmel_smc_cs_conf smcconf;
+	struct atmel_nand_cs *cs;
+	int ret;
+
+	nc = to_nand_controller(nand->base.controller);
+
+	ret = atmel_smc_nand_prepare_smcconf(nand, conf, &smcconf);
+	if (ret)
+		return ret;
+
+	if (csline == NAND_DATA_IFACE_CHECK_ONLY)
+		return 0;
+
+	cs = &nand->cs[csline];
+	cs->smcconf = smcconf;
+	atmel_smc_cs_conf_apply(nc->smc, cs->id, &cs->smcconf);
+
+	return 0;
+}
+
+static int atmel_hsmc_nand_setup_data_interface(struct atmel_nand *nand,
+					int csline,
+					const struct nand_data_interface *conf)
+{
+	struct atmel_nand_controller *nc;
+	struct atmel_smc_cs_conf smcconf;
+	struct atmel_nand_cs *cs;
+	int ret;
+
+	nc = to_nand_controller(nand->base.controller);
+
+	ret = atmel_smc_nand_prepare_smcconf(nand, conf, &smcconf);
+	if (ret)
+		return ret;
+
+	if (csline == NAND_DATA_IFACE_CHECK_ONLY)
+		return 0;
+
+	cs = &nand->cs[csline];
+	cs->smcconf = smcconf;
+
+	if (cs->rb.type == ATMEL_NAND_NATIVE_RB)
+		cs->smcconf.timings |= ATMEL_HSMC_TIMINGS_RBNSEL(cs->rb.id);
+
+	atmel_hsmc_cs_conf_apply(nc->smc, cs->id, &cs->smcconf);
+
+	return 0;
+}
+
+static int atmel_nand_setup_data_interface(struct mtd_info *mtd, int csline,
+					const struct nand_data_interface *conf)
+{
+	struct nand_chip *chip = mtd_to_nand(mtd);
+	struct atmel_nand *nand = to_atmel_nand(chip);
+	struct atmel_nand_controller *nc;
+
+	nc = to_nand_controller(nand->base.controller);
+
+	if (csline >= nand->numcs ||
+	    (csline < 0 && csline != NAND_DATA_IFACE_CHECK_ONLY))
+		return -EINVAL;
+
+	return nc->caps->ops->setup_data_interface(nand, csline, conf);
+}
+
 static void atmel_nand_init(struct atmel_nand_controller *nc,
 			    struct atmel_nand *nand)
 {
@@ -1192,6 +1489,9 @@ static void atmel_nand_init(struct atmel_nand_controller *nc,
 	chip->write_buf = atmel_nand_write_buf;
 	chip->select_chip = atmel_nand_select_chip;
 
+	if (nc->mck && nc->caps->ops->setup_data_interface)
+		chip->setup_data_interface = atmel_nand_setup_data_interface;
+
 	/* Some NANDs require a longer delay than the default one (20us). */
 	chip->chip_delay = 40;
 
@@ -1677,6 +1977,12 @@ static int atmel_nand_controller_init(struct atmel_nand_controller *nc,
 	if (nc->caps->legacy_of_bindings)
 		return 0;
 
+	nc->mck = of_clk_get(dev->parent->of_node, 0);
+	if (IS_ERR(nc->mck)) {
+		dev_err(dev, "Failed to retrieve MCK clk\n");
+		return PTR_ERR(nc->mck);
+	}
+
 	np = of_parse_phandle(dev->parent->of_node, "atmel,smc", 0);
 	if (!np) {
 		dev_err(dev, "Missing or invalid atmel,smc property\n");
@@ -1983,6 +2289,7 @@ static const struct atmel_nand_controller_ops atmel_hsmc_nc_ops = {
 	.remove = atmel_hsmc_nand_controller_remove,
 	.ecc_init = atmel_hsmc_nand_ecc_init,
 	.nand_init = atmel_hsmc_nand_init,
+	.setup_data_interface = atmel_hsmc_nand_setup_data_interface,
 };
 
 static const struct atmel_nand_controller_caps atmel_sama5_nc_caps = {
@@ -2037,7 +2344,14 @@ atmel_smc_nand_controller_remove(struct atmel_nand_controller *nc)
 	return 0;
 }
 
-static const struct atmel_nand_controller_ops atmel_smc_nc_ops = {
+/*
+ * The SMC reg layout of at91rm9200 is completely different which prevents us
+ * from re-using atmel_smc_nand_setup_data_interface() for the
+ * ->setup_data_interface() hook.
+ * At this point, there's no support for the at91rm9200 SMC IP, so we leave
+ * ->setup_data_interface() unassigned.
+ */
+static const struct atmel_nand_controller_ops at91rm9200_nc_ops = {
 	.probe = atmel_smc_nand_controller_probe,
 	.remove = atmel_smc_nand_controller_remove,
 	.ecc_init = atmel_nand_ecc_init,
@@ -2047,6 +2361,20 @@ static const struct atmel_nand_controller_ops atmel_smc_nc_ops = {
 static const struct atmel_nand_controller_caps atmel_rm9200_nc_caps = {
 	.ale_offs = BIT(21),
 	.cle_offs = BIT(22),
+	.ops = &at91rm9200_nc_ops,
+};
+
+static const struct atmel_nand_controller_ops atmel_smc_nc_ops = {
+	.probe = atmel_smc_nand_controller_probe,
+	.remove = atmel_smc_nand_controller_remove,
+	.ecc_init = atmel_nand_ecc_init,
+	.nand_init = atmel_smc_nand_init,
+	.setup_data_interface = atmel_smc_nand_setup_data_interface,
+};
+
+static const struct atmel_nand_controller_caps atmel_sam9260_nc_caps = {
+	.ale_offs = BIT(21),
+	.cle_offs = BIT(22),
 	.ops = &atmel_smc_nc_ops,
 };
 
@@ -2093,7 +2421,7 @@ static const struct of_device_id atmel_nand_controller_of_ids[] = {
 	},
 	{
 		.compatible = "atmel,at91sam9260-nand-controller",
-		.data = &atmel_rm9200_nc_caps,
+		.data = &atmel_sam9260_nc_caps,
 	},
 	{
 		.compatible = "atmel,at91sam9261-nand-controller",
@@ -2181,6 +2509,24 @@ static int atmel_nand_controller_remove(struct platform_device *pdev)
 	return nc->caps->ops->remove(nc);
 }
 
+static __maybe_unused int atmel_nand_controller_resume(struct device *dev)
+{
+	struct atmel_nand_controller *nc = dev_get_drvdata(dev);
+	struct atmel_nand *nand;
+
+	list_for_each_entry(nand, &nc->chips, node) {
+		int i;
+
+		for (i = 0; i < nand->numcs; i++)
+			nand_reset(&nand->base, i);
+	}
+
+	return 0;
+}
+
+static SIMPLE_DEV_PM_OPS(atmel_nand_controller_pm_ops, NULL,
+			 atmel_nand_controller_resume);
+
 static struct platform_driver atmel_nand_controller_driver = {
 	.driver = {
 		.name = "atmel-nand-controller",
diff --git a/drivers/mtd/nand/bcm47xxnflash/ops_bcm4706.c b/drivers/mtd/nand/bcm47xxnflash/ops_bcm4706.c
index f1da4ea88f2c..54bac5b73f0a 100644
--- a/drivers/mtd/nand/bcm47xxnflash/ops_bcm4706.c
+++ b/drivers/mtd/nand/bcm47xxnflash/ops_bcm4706.c
@@ -392,6 +392,8 @@ int bcm47xxnflash_ops_bcm4706_init(struct bcm47xxnflash *b47n)
 	b47n->nand_chip.read_byte = bcm47xxnflash_ops_bcm4706_read_byte;
 	b47n->nand_chip.read_buf = bcm47xxnflash_ops_bcm4706_read_buf;
 	b47n->nand_chip.write_buf = bcm47xxnflash_ops_bcm4706_write_buf;
+	b47n->nand_chip.onfi_set_features = nand_onfi_get_set_features_notsupp;
+	b47n->nand_chip.onfi_get_features = nand_onfi_get_set_features_notsupp;
 
 	nand_chip->chip_delay = 50;
 	b47n->nand_chip.bbt_options = NAND_BBT_USE_FLASH;
diff --git a/drivers/mtd/nand/cafe_nand.c b/drivers/mtd/nand/cafe_nand.c
index d40c32d311d8..2fd733eba0a3 100644
--- a/drivers/mtd/nand/cafe_nand.c
+++ b/drivers/mtd/nand/cafe_nand.c
@@ -654,6 +654,8 @@ static int cafe_nand_probe(struct pci_dev *pdev,
 	cafe->nand.read_buf = cafe_read_buf;
 	cafe->nand.write_buf = cafe_write_buf;
 	cafe->nand.select_chip = cafe_select_chip;
+	cafe->nand.onfi_set_features = nand_onfi_get_set_features_notsupp;
+	cafe->nand.onfi_get_features = nand_onfi_get_set_features_notsupp;
 
 	cafe->nand.chip_delay = 0;
 
diff --git a/drivers/mtd/nand/davinci_nand.c b/drivers/mtd/nand/davinci_nand.c
index 531c51991e57..7b26e53b95b1 100644
--- a/drivers/mtd/nand/davinci_nand.c
+++ b/drivers/mtd/nand/davinci_nand.c
@@ -771,11 +771,14 @@ static int nand_davinci_probe(struct platform_device *pdev)
 			info->chip.ecc.hwctl = nand_davinci_hwctl_4bit;
 			info->chip.ecc.bytes = 10;
 			info->chip.ecc.options = NAND_ECC_GENERIC_ERASED_CHECK;
+			info->chip.ecc.algo = NAND_ECC_BCH;
 		} else {
+			/* 1bit ecc hamming */
 			info->chip.ecc.calculate = nand_davinci_calculate_1bit;
 			info->chip.ecc.correct = nand_davinci_correct_1bit;
 			info->chip.ecc.hwctl = nand_davinci_hwctl_1bit;
 			info->chip.ecc.bytes = 3;
+			info->chip.ecc.algo = NAND_ECC_HAMMING;
 		}
 		info->chip.ecc.size = 512;
 		info->chip.ecc.strength = pdata->ecc_bits;
diff --git a/drivers/mtd/nand/denali.c b/drivers/mtd/nand/denali.c
index 16634df2e39a..d723be352148 100644
--- a/drivers/mtd/nand/denali.c
+++ b/drivers/mtd/nand/denali.c
@@ -23,50 +23,43 @@
 #include <linux/mutex.h>
 #include <linux/mtd/mtd.h>
 #include <linux/module.h>
+#include <linux/slab.h>
 
 #include "denali.h"
 
 MODULE_LICENSE("GPL");
 
-/*
- * We define a module parameter that allows the user to override
- * the hardware and decide what timing mode should be used.
- */
-#define NAND_DEFAULT_TIMINGS	-1
+#define DENALI_NAND_NAME    "denali-nand"
 
-static int onfi_timing_mode = NAND_DEFAULT_TIMINGS;
-module_param(onfi_timing_mode, int, S_IRUGO);
-MODULE_PARM_DESC(onfi_timing_mode,
-	   "Overrides default ONFI setting. -1 indicates use default timings");
+/* Host Data/Command Interface */
+#define DENALI_HOST_ADDR	0x00
+#define DENALI_HOST_DATA	0x10
 
-#define DENALI_NAND_NAME    "denali-nand"
+#define DENALI_MAP00		(0 << 26)	/* direct access to buffer */
+#define DENALI_MAP01		(1 << 26)	/* read/write pages in PIO */
+#define DENALI_MAP10		(2 << 26)	/* high-level control plane */
+#define DENALI_MAP11		(3 << 26)	/* direct controller access */
 
-/*
- * We define a macro here that combines all interrupts this driver uses into
- * a single constant value, for convenience.
- */
-#define DENALI_IRQ_ALL	(INTR__DMA_CMD_COMP | \
-			INTR__ECC_TRANSACTION_DONE | \
-			INTR__ECC_ERR | \
-			INTR__PROGRAM_FAIL | \
-			INTR__LOAD_COMP | \
-			INTR__PROGRAM_COMP | \
-			INTR__TIME_OUT | \
-			INTR__ERASE_FAIL | \
-			INTR__RST_COMP | \
-			INTR__ERASE_COMP)
+/* MAP11 access cycle type */
+#define DENALI_MAP11_CMD	((DENALI_MAP11) | 0)	/* command cycle */
+#define DENALI_MAP11_ADDR	((DENALI_MAP11) | 1)	/* address cycle */
+#define DENALI_MAP11_DATA	((DENALI_MAP11) | 2)	/* data cycle */
 
-/*
- * indicates whether or not the internal value for the flash bank is
- * valid or not
- */
-#define CHIP_SELECT_INVALID	-1
+/* MAP10 commands */
+#define DENALI_ERASE		0x01
+
+#define DENALI_BANK(denali)	((denali)->active_bank << 24)
+
+#define DENALI_INVALID_BANK	-1
+#define DENALI_NR_BANKS		4
 
 /*
- * This macro divides two integers and rounds fractional values up
- * to the nearest integer value.
+ * The bus interface clock, clk_x, is phase aligned with the core clock.  The
+ * clk_x is an integral multiple N of the core clk.  The value N is configured
+ * at IP delivery time, and its available value is 4, 5, or 6.  We need to align
+ * to the largest value to make it work with any possible configuration.
  */
-#define CEIL_DIV(X, Y) (((X)%(Y)) ? ((X)/(Y)+1) : ((X)/(Y)))
+#define DENALI_CLK_X_MULT	6
 
 /*
  * this macro allows us to convert from an MTD structure to our own
@@ -77,339 +70,11 @@ static inline struct denali_nand_info *mtd_to_denali(struct mtd_info *mtd)
 	return container_of(mtd_to_nand(mtd), struct denali_nand_info, nand);
 }
 
-/*
- * These constants are defined by the driver to enable common driver
- * configuration options.
- */
-#define SPARE_ACCESS		0x41
-#define MAIN_ACCESS		0x42
-#define MAIN_SPARE_ACCESS	0x43
-
-#define DENALI_READ	0
-#define DENALI_WRITE	0x100
-
-/*
- * this is a helper macro that allows us to
- * format the bank into the proper bits for the controller
- */
-#define BANK(x) ((x) << 24)
-
-/* forward declarations */
-static void clear_interrupts(struct denali_nand_info *denali);
-static uint32_t wait_for_irq(struct denali_nand_info *denali,
-							uint32_t irq_mask);
-static void denali_irq_enable(struct denali_nand_info *denali,
-							uint32_t int_mask);
-static uint32_t read_interrupt_status(struct denali_nand_info *denali);
-
-/*
- * Certain operations for the denali NAND controller use an indexed mode to
- * read/write data. The operation is performed by writing the address value
- * of the command to the device memory followed by the data. This function
- * abstracts this common operation.
- */
-static void index_addr(struct denali_nand_info *denali,
-				uint32_t address, uint32_t data)
-{
-	iowrite32(address, denali->flash_mem);
-	iowrite32(data, denali->flash_mem + 0x10);
-}
-
-/* Perform an indexed read of the device */
-static void index_addr_read_data(struct denali_nand_info *denali,
-				 uint32_t address, uint32_t *pdata)
-{
-	iowrite32(address, denali->flash_mem);
-	*pdata = ioread32(denali->flash_mem + 0x10);
-}
-
-/*
- * We need to buffer some data for some of the NAND core routines.
- * The operations manage buffering that data.
- */
-static void reset_buf(struct denali_nand_info *denali)
-{
-	denali->buf.head = denali->buf.tail = 0;
-}
-
-static void write_byte_to_buf(struct denali_nand_info *denali, uint8_t byte)
-{
-	denali->buf.buf[denali->buf.tail++] = byte;
-}
-
-/* reads the status of the device */
-static void read_status(struct denali_nand_info *denali)
-{
-	uint32_t cmd;
-
-	/* initialize the data buffer to store status */
-	reset_buf(denali);
-
-	cmd = ioread32(denali->flash_reg + WRITE_PROTECT);
-	if (cmd)
-		write_byte_to_buf(denali, NAND_STATUS_WP);
-	else
-		write_byte_to_buf(denali, 0);
-}
-
-/* resets a specific device connected to the core */
-static void reset_bank(struct denali_nand_info *denali)
-{
-	uint32_t irq_status;
-	uint32_t irq_mask = INTR__RST_COMP | INTR__TIME_OUT;
-
-	clear_interrupts(denali);
-
-	iowrite32(1 << denali->flash_bank, denali->flash_reg + DEVICE_RESET);
-
-	irq_status = wait_for_irq(denali, irq_mask);
-
-	if (irq_status & INTR__TIME_OUT)
-		dev_err(denali->dev, "reset bank failed.\n");
-}
-
-/* Reset the flash controller */
-static uint16_t denali_nand_reset(struct denali_nand_info *denali)
-{
-	int i;
-
-	for (i = 0; i < denali->max_banks; i++)
-		iowrite32(INTR__RST_COMP | INTR__TIME_OUT,
-		denali->flash_reg + INTR_STATUS(i));
-
-	for (i = 0; i < denali->max_banks; i++) {
-		iowrite32(1 << i, denali->flash_reg + DEVICE_RESET);
-		while (!(ioread32(denali->flash_reg + INTR_STATUS(i)) &
-			(INTR__RST_COMP | INTR__TIME_OUT)))
-			cpu_relax();
-		if (ioread32(denali->flash_reg + INTR_STATUS(i)) &
-			INTR__TIME_OUT)
-			dev_dbg(denali->dev,
-			"NAND Reset operation timed out on bank %d\n", i);
-	}
-
-	for (i = 0; i < denali->max_banks; i++)
-		iowrite32(INTR__RST_COMP | INTR__TIME_OUT,
-			  denali->flash_reg + INTR_STATUS(i));
-
-	return PASS;
-}
-
-/*
- * this routine calculates the ONFI timing values for a given mode and
- * programs the clocking register accordingly. The mode is determined by
- * the get_onfi_nand_para routine.
- */
-static void nand_onfi_timing_set(struct denali_nand_info *denali,
-								uint16_t mode)
-{
-	uint16_t Trea[6] = {40, 30, 25, 20, 20, 16};
-	uint16_t Trp[6] = {50, 25, 17, 15, 12, 10};
-	uint16_t Treh[6] = {30, 15, 15, 10, 10, 7};
-	uint16_t Trc[6] = {100, 50, 35, 30, 25, 20};
-	uint16_t Trhoh[6] = {0, 15, 15, 15, 15, 15};
-	uint16_t Trloh[6] = {0, 0, 0, 0, 5, 5};
-	uint16_t Tcea[6] = {100, 45, 30, 25, 25, 25};
-	uint16_t Tadl[6] = {200, 100, 100, 100, 70, 70};
-	uint16_t Trhw[6] = {200, 100, 100, 100, 100, 100};